lock LAND ROVER DEFENDER 1999 Workshop Manual

76CHASSIS AND BODY
18
REPAIR AUXILLIARY SWITCH PANEL
Service repair no - 76.46.38
Remove
1.Remove 2 screws securing axilliary switch panel
to fascia and collect nuts and washers.
2.Disconnect multiplug from headlamp Levelling
switch.
3.Disconnect multiplug and Lucar from cigar
lighter.
4.Noting their fitted position, disconnect 4 Lucars
from rear wash wipe switch.
5.Remove switch panel.Do not carry out further dismantling if
component is removed for access only.6.Release pin securing rear wash wipe knob to
switch and remove knob.
7.Remove locknut securing rear wash wipe switch
to panel.
8.Remove rear wash wipe switch.
9.Remove knob from headlamp levelling switch.
10.Remove locknut securing headlamp switch to
panel.
11.Remove headlamp levelling switch.
12.Remove element from cigar lighter.
13.Release bulb holder from cigar lighter.
14.Release cigar lighter from tags and remove from
panel.
15.Fit cigar lighter to panel and locate tags.
16.Fit bulb holder to cigar lighter.
17.Fit element to cigar lighter.
18.Fit headlamp levelling switch to panel and
secure with locknut.
19.Fit knob to headlamp levelling switch.
20.Fit rear wash wipe switch to panel and secure
with locknut.
21.Fit knob to rear wash wipe switch, ensuring pin
is correctly located.
Refit
22.Position auxilliary switch panel to fascia and
connect 4 Lucars to rear wash wipe switch.
23.Connect multiplug and Lucar to cigar lighter.
24.Connect multiplug to headlamp levelling switch.
25.Fit auxilliary switch panel to fascia and secure
with screws.
ProCarManuals.com

CHASSIS AND BODY
19
REPAIR LOWER FASCIA PANEL - UP TO 02MY
Service repair no - 76.46.05
Remove
1.Disconnect battery negative lead.
2.Remove steering wheel.See STEERING,
Repair.
3.Remove 7 screws securing nacelle to steering
column.
4.Remove 2 halves of nacelle from steering
column.
5.Remove instrument pack.See ELECTRICAL,
Repair.
6.Remove 3 screws securing heater control cable
assembly to end of fascia.
7.Release heater control cable assembly from
fascia and move aside.
8.Release HRW, Rear Fog Guard Lamp, and
Hazard Warning switches from fascia.
9.Disconnect multiplugs and Lucars from switches.
10.Collect switches.
11.Remove locking rings from both front speakers.
12.Remove 4 screws securing each speaker to
fascia.
13.Disconnect multiplugs from speakers and
remove both front speakers.
ProCarManuals.com

CHASSIS AND BODY
23
REPAIR 59.Fit radio housing to fascia and secure with trim
studs.
60.Position radio to fascia and connect multiplugs
and aerial.
61.Fit radio to fascia.
62.Fit crash pad to fascia and secure with screws.
63.Fit both demister vents to crash pad and secure
with screws.
64.Fit grab handle to fascia and secure with screws.
65.Fit Land Rover decal to grab handle.
66.Position both front speakers to fascia and
connect multiplugs.
67.Fit speakers to fascia and secure with screws.
68.Fit locking rings to speakers.
69.Connect multiplugs and Lucars to HRW, Rear
Fog Guard Lamp, and Hazard Warning
Switches.
70.Fit switches to fascia.
71.Position heater controls to fascia and secure
with screws.
72.Fit instrument pack.See ELECTRICAL,
Repair.
73.Fit 2 halves of nacelle to steering column and
secure with screws.
74.Fit steering wheel.See STEERING, Repair.
75.Reconnect battery negative lead.PANEL - MOUNTING - FRONT DOOR - FROM 02MY
Service repair no - 76.11.28
Remove
1.Remove plastic sheet.See this Section.
2.Lower glass and remove 2 bolts securing door
glass to regulator.
3.Release glass from regulator, raise and wedge
in raised position.
ProCarManuals.com

76CHASSIS AND BODY
24
REPAIR
4.Release clip, detach and remove lock solenoid
link.
5.Loosen 2 screws securing solenoid, release
solenoid from mounting panel, disconnect
multiplug and remove solenoid.
6.Release clip and disconnect interior handle link
from latch mechanism.7.Release clips securing harness to panel.
8.Disconnect multiplug from motor.
9.Release harness sleeve and withdraw harness
from door.
10.Remove 6 bolts and 1 nut securing panel.
11.Remove panel assembly.
ProCarManuals.com

CHASSIS AND BODY
25
REPAIR Refit
12.Position panel assembly, fit bolts and nut and
tighten to10 Nm (7lbf.ft).
13.Connect multiplug to motor.
14.Secure harness clips and sleeve.
15.Connect interior handle link to latch and secure
with clip.
16.Connect multiplug to solenoid, locate solenoid to
mounting panel and tighten screws.
17.Fit and secure link.
18.Remove wedges, lower glass and locate to
regulator. Fit bolts and tighten to6 Nm (4 lbf.ft).
19.Raise and lower glass to check operation.
20.Fit plastic sheet.See this Section.
21.Adjust door lock solenoid.See ELECTRICAL,
Adjustment.PANEL - MOUNTING - REAR DOOR - FROM 02MY
Service repair no - 76.11.29
Remove
1.Remove plastic sheet.See this Section.
2.Lower glass and remove 2 bolts securing door
glass to regulator.
3.Release glass from regulator, raise and wedge
in raised position.
ProCarManuals.com

76CHASSIS AND BODY
26
REPAIR
4.Release clip, detach and remove lock solenoid
link.
5.Release clip and disconnect interior handle link
from latch mechanism.
6.Remove clip and disconnect sill button link.
7.Release clips securing harness to panel.
8.Disconnect multiplug from solenoid.
9.Release harness sleeve and withdraw harness
from door.
10.Remove 5 bolts and 1 nut securing panel.
11.Remove panel assembly.
Refit
12.Position door mounting panel assembly, fit bolts
and nut and tighten to10 Nm (7lbf.ft).
13.Connect multiplug to solenoid.
14.Secure harness clips and sleeve.
15.Connect interior handle link to latch and secure
with clip.
16.Connect link to sill button and fit clip.
17.Fit and secure solenoid link.
18.Remove wedges, lower glass and locate to
regulator. Fit bolts and tighten to6 Nm (4 lbf.ft).
19.Raise and lower glass to check operation.
20.Fit plastic sheet.See this Section.
ProCarManuals.com

CHASSIS AND BODY
35
REPAIR LOCK - TAIL DOOR - FROM 02MY
Service repair no - 76.37.16
Remove
1.Remove tail door trim casing.See this Section.
2.Remove 4 nuts securing tail door lock.
3.Partially withdraw lock assembly, carefully
disconnect central door locking rod from fulcrum
arm.
4.Remove lock assembly.
5.Remove door lock gasket.
NOTE: Do not carry out further
dismantling if component is removed for
access only.
6.Insert key in lock, depress lock barrel plunger
and withdraw barrel from lock.Refit
7.Fit new barrel to lock.
8.Fit new door lock gasket.
9.Fit door locking rod to fulcrum, align lock. Fit and
tighten nuts to10 Nm (7 lbf.ft ).
10.Close door and check for correct latching with
striker. Adjust striker if necessary.See
Adjustment.
11.Fit tail door trim casing.See this Section.
ProCarManuals.com

PANEL REPAIRS
21
SEALING AND CORROSION PROTECTION Seam sealer on rear end assembly
CAUTION: Do not block drain holes when applying seam sealer.
ProCarManuals.com

PANEL REPAIRS
3
PROCEDURES
4.Cut away the bulk of the panel as necessary
using an air saw.
NOTE: On certain panel joints MIG welds
and braze should be removed using a
sander where possible, before cutting out
the panel bulk.
5.Separate spot welded joints and remove panel
remnants using hammer, bolster chisel and
pincers.Prepare Old Surfaces
6.Clean all panel joint edges to a bright smooth
finish, using a belt-type sander.
NOTE: Prior to sanding, remove remaining
sealant using a hot air gun to minimise the
risk of toxic fumes caused by generated
heat.
WARNING: Care must be taken to avoid
excessive heat build up which may be
caused by this equipment.
7.Straighten existing joint edges using shaping
block and hammer.
CAUTION: Where significant straightening
is required, heat must be applied to the
area to avoid stretching the Aluminium.
CAUTION: All tools used for working with
Aluminium must be kept separate from
those used on steel.
ProCarManuals.com

84WIPERS AND WASHERS
2
DESCRIPTION AND OPERATION WINDSCREEN WIPERS - FROM 02MY
1.LH wheelbox
2.Cable
3.RH wheelbox
4.Wiper motor
5.Spindle with DIN taper arm attachment
6.Spacer
7.Locknut
8.Seal
9.Locknuts
ProCarManuals.com