service LAND ROVER DEFENDER 1999 User Guide

10 - MAINTENANCE
CONTENTS
Page
ROAD TEST 23......................................................................................................
ENDORSE SERVICE RECORD 24........................................................................
REPORT ANY UNUSUAL FEATURES 24.............................................................
ProCarManuals.com

MAINTENANCE
3
MAINTENANCE WIPERS AND WASHERS
1.Operate screen washer and switch on wipers.
Check washer jets are correctly aimed and
check for smooth smearless operation across
screen of wiper blades at all speeds, including
intermittent.
2.Repeat operation for rear screen
wipers/washers.
3.Check all wiper blades for condition and signs of
splits or damage.
4.Check security of wiper arms.HANDBRAKE
1.With the vehicle stationary, apply handbrake and
check for correct operation.See BRAKES,
Adjustment.
2.Release handbrake and check for correct
operation.
NOTE: Any adjustment required as a result
of the checking process will be subject to
additional labour and/or material cost and
should not be carried out without the
authorisation of the customer.
Adjust handbrake (First 12,000 miles/12 months
only
1.Adjust handbrake cable.See BRAKES,
Adjustment.
NOTE: Additional time is built into the first
12,000/12 months service time to allow for
handbrake cable adjustment.
ProCarManuals.com

10MAINTENANCE
12
MAINTENANCE AUXILIARY DRIVE BELT
Check
1.Check auxiliary drive belt for signs of splits,
fraying, oil contamination and wear.
NOTE: Any requirement to replace the
auxiliary drive belt should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
Renew
1.Renew auxiliary drive belt.See ELECTRICAL,
Repair.
NOTE: Additional time is built into the
96,000/8 year service time to allow for
auxiliary drive belt renewal.PAS FLUID, CLUTCH FLUID AND SCREEN
WASHER LEVELS
PAS Fluid
1.Clean arear around PAS reservoir filler cap, and
remove cap.
2.Check fluid level in PAS reservoir.
3.Top-up if necessary to the correct level using
recommended fluid.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information.
4.Fit filler cap.
ProCarManuals.com

MAINTENANCE
21
MAINTENANCE STEERING BALL JOINTS
1.Check for wear in joints by moving ball joint up
and down vigorously. If free movement is
apparent, fit a new joint assembly.
2.Check condition of steering ball joints paying
particular attention to dust covers.
NOTE: Any requirement to replace the
steering ball joints should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
NOTE: Ball joints are lubricated for life
during manufacture and require no further
lubrication unless the rubber boot has
been dislodged or damaged. All joints should be
checked at specified service intervals, but more
frequently if vehicle is used under arduous
conditions.
ProCarManuals.com

10MAINTENANCE
24
MAINTENANCE ENDORSE SERVICE RECORD
1.Insert date and mileage of next service.
2.Insert current mileage.
3.Tick one of the boxes on the brake fluid
replacement indicator.
4.Endorse service record with dealer stamp.
5.Sign and date the service record.
6.Sign and date the maintenance check sheet.REPORT ANY UNUSUAL FEATURES
1.Produce a written report detailing additional work
necessary, or items which may require attention
prior to the next service.
ProCarManuals.com

ENGINE
23
DESCRIPTION AND OPERATION Oil pump
1.Stiffener plate
2.Ring dowel
3.Outlet port
4.Outer rotor
5.Inner rotor6.Spring dowel
7.Oil pressure relief valve cap
8.Oil pressure relief valve spring
9.Oil pressure relief valve plunger
10.Inlet port
The eccentric rotor oil pump is integrated with the stiffener plate and contains no serviceable parts except for the
pressure relief valve spring. The oil pump drive sprocket is attached to the front of the stiffener plate and is driven
through a chain and sprocket system.
A pressure relief valve is included at the outlet side of the oil pump to restrict oil pressure at high engine speeds by
recirculating oil through the relief valve back around the pump to the inlet. The relief valve and spring is a plunger
type. When oil pressure is great enough to lift the plunger, oil is allowed to escape past the plunger to relieve
pressure and prevent further rise.
Oil is delivered to the pump from the pick-up through a channel in the stiffener plate. The outlet side of the oil
pump delivers pressurised oil flow to the engine block main oil delivery gallery through a port in the stiffener plate.
Piston lubrication jets
Piston lubrication jets are fitted to the cylinder block to provide lubrication to the cylinder walls and to the piston
underskirt for cooling the pistons and lubricating the gudgeon pins. The input port to each lubrication jet mates
with a port provided in each mounting position tapped at the underside of the cylinder block from the main oil
delivery gallery. When oil pressure is sufficient to supply flow through the jets, oil is squirted to the inside of the
cylinder walls to provide piston to wall lubrication and cooling and to the underside of the piston skirt at the bottom
of the piston stroke (gallery cooled piston). The squirt jets also provide splash feed lubrication supply to the small
end bearings of the connecting rods.
Each lubrication jet is fixed to a mounting position on the underside of the engine block by a single Torx screw.
Chain lubrication jet
A chain lubrication jet is located on the front face of the cylinder block, behind the front engine timing chain cover.
The inlet port to the lubrication jet mates with an oil supply port from the cylinder block main oil delivery gallery.
The lubrication jet is fixed to the front of the engine block by a single screw. Additional chain lubrication is provided
by oil supply through a small aperture tapped from the cylinder head oil delivery gallery.
ProCarManuals.com

12ENGINE
26
DESCRIPTION AND OPERATION Fuel connector block
Type A - Non EU3 Models - Engine Serial No. Prefixes 10P to 14P
Type B - EU3 Models - Engine Serial No. Prefixes 15P to 19P
1.Fuel connector block assembly
2.Outlet stub pipe
3.Stub pipe - to fuel cooler4.Fuel temperature sensor
5.Fuel pressure regulator
6.Spill return fuel connection (EU3 models only)
A cast and machined aluminium alloy fuel connector block assembly is located at the rear RH side of the cylinder
head, attached by three flanged bolts. A metal gasket is used to seal the faces between the fuel connector block
and the cylinder head, which must be replaced every time the fuel connector block is removed.
CAUTION: The cylinder head incorporates drillings for the fuel injection system, any
contamination which enters these drillings could cause engine running problems or injector
failure. It is therefore, essential that absolute cleanliness is maintained when carrying out work on
the cylinder head.
CAUTION: The valve heads, tips of the injectors and glow plugs protrude below the face of the
cylinder head and will be damaged if the cylinder head is stored face down.
Camshaft carrier
The cast aluminium alloy camshaft carrier is bolted to the cylinder head by thirteen screws. The camshaft carrier
and cylinder head assembly is attached to the cylinder block by twelve cylinder head retaining bolts which pass
through the camshaft carrier and the cylinder head to secure the assembly to the cylinder block.
The carrier is machined together with the cylinder head to form a matched pair for carrying the camshaft.
Non-return valve
A non-return valve is located at the front, bottom LH side of the cylinder head. The non-return valve prevents oil
from draining from the lash adjusters and is an integral component within the cylinder head and is
non-serviceable.
ProCarManuals.com

12ENGINE
28
DESCRIPTION AND OPERATION Inlet and exhaust valves
The inlet and exhaust valves are mounted directly above the engine block cylinders.
Each valve is a forged and ground solid one-piece head and stem which is hardened by heat treatment. The
stems are chrome-plated then ground for improved heat transfer, wear resistance and smooth operation. It is not
possible to recut the valve’s face angle, but the valves can be lapped to their seats using grinding paste.
The valve springs are made from spring steel and are of the parallel single-coil type. The bottom end of the spring
rests on the flange of a spring seal which has a centre bore that locates on a recess ground into the lower valve
stem. The top end of the spring is held in place by a spring cap which is held in position at the top end of the valve
stem by split taper collets. The taper collets have grooves on the internal bore that locate in grooves ground into
the upper stems of the valves.
The valve seats and valve guides are sintered and are an interference fit into the cylinder head. The valve seats
and guides are non-serviceable.
Finger followers and lash adjusters
1.Valve stem
2.Finger follower
3.Lash adjuster plunger4.Oil supply hole
5.Lash adjuster body
The valves are operated through finger followers and lash adjusters, actuated by the camshaft lobes. When the
camshaft lobe presses down on the top of a finger follower roller mechanism, the respective valve is forced down
opening the inlet or exhaust port.
The lash adjuster body contains a plunger and two chambers for oil feed and pressurised oil. Pressurised oil is
supplied to the lash adjusters via the oil galleries in the cylinder head and through a hole in the side of the lash
adjuster body. The oil passes into a feed chamber in the lash adjuster then through to a separate pressure
chamber via a one way ball valve. Oil flow from the pressure chamber is determined by the amount of clearance
between the lash adjuster outer body and the centre plunger, oil escapes up the side of the plunger every time the
lash adjuster is operated, the downward pressure on the plunger forcing a corresponding amount of oil in the lash
adjuster body to be displaced. When the downward pressure from the camshaft and finger follower is removed
(i.e. after the trailing flank of the camshaft lobe has passed), oil pressure forces the lash adjuster’s plunger up
again. This pressure is not sufficient to effect the valve operation, but eliminates the clearance between the finger
follower and top of the valve stem.
ProCarManuals.com

ENGINE
1
ADJUSTMENT ENGINE OIL PRESSURE CHECK
Service repair no - 12.90.09.01
Check
1.Remove oil pressure switch.See Repair.
2.Connect pressure check kitLRT-12-052C
adaptor and gauge to oil pressure switch
position on oil cooler.
3.Check and if necessary, top-up engine oil.
4.Run engine at idle speed and check that oil
pressure is within limits given.
5.Switch off ignition.
6.Remove oil pressure check kitLRT-12-052C.
7.Clean oil spillage.
8.Fit oil pressure switch.See Repair.
Adjust
1.If engine oil pressure is not within specified
limits, check condition of oil pump and/or main
and connecting rod bearings.
ProCarManuals.com

ENGINE
1
REPAIR CAMSHAFT
Service repair no - 12.13.02
Remove
1.Remove cylinder head gasket.See this
Section.
2.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
3.Disconnect multiplug from injector units and
remove harness from camshaft carrier.
4.Remove and discard multiplug’O’ring.
5.Loosen lock nuts and fully retract rocker
adjusting screws.
6.Progressively loosen then remove and discard 6
bolts securing rocker shaft, remove shaft.
7.Using sequence shown, progressively loosen
then remove 13 bolts securing camshaft carrier
to cylinder head.
8.Gently tap the camshaft carrier upwards to break
the sealant bond and remove carrier noting it is
located by 2 dowels.
9.Remove camshaft.
10.Remove and discard camshaft rear oil seal.
11.Remove and discard lock nuts and rocker
adjusting screws.
12.Check bearing surfaces in cylinder head and
camshaft carrier for signs of scoring and wear.
ProCarManuals.com