clutch LAND ROVER DISCOVERY 1995 User Guide

Tdi
5
REPAIR
37.Remove nuts and plain washers securing front
engine mountings to chassis,and lift both engine
mounting bracket assemblies from vehicle.
38.Remove engine to bell housing fixings. Leave
starter motor attached.
39.Raise engine to separate from transmission.
40.Check all connections to engine have been
disconnected.
41.Remove engine.Refit
42.Apply Hylomar to mating faces of bell housing.
Lubricate splines of gearbox primary pinion with
Rocol MV 3.
If automatic transmission, coat the four drive
plate to torque convertor bolts with Loctite 290.
Tighten to
39 Nm.
43.Lower engine and locate with transmission.
If manual transmission locate primary pinion into
clutch and engage bell housing dowels. Fit
engine to bell housing fixings. Tighten to
40 Nm.
If automatic transmission fixings. Tighten to46
Nm.
44.Raise engine, refit front engine mounting
brackets to cylinder block and bell housing.
45.Remove gearbox support and lower engine.
46.Tighten front engine mountings to chassis
fixings. Tighten to
45 Nm.
47.Reverse removal procedure. 1 to 37.

12ENGINE
14
REPAIR FLYWHEEL
Service repair no - 12.53.07
Remove
1.Disconnect battery negative lead.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
Assembly
4.Fit two long 8mm bolts into the clutch bolt holes,
diametrically opposite, to use as handles when
lifting the flywheel off the crankshaft.
5.Remove fan cowl
6.Fit crankshaft pulley retainer LRT-12-080 and
secure with four bolts, to restrain crankshaft
while removing flywheel retaining bolts.
7.Remove the bolts and lift off flywheel.
NOTE: To prevent excessive flywheel
run-out, ensure that the mating faces of
the flywheel and crankshaft are clean.Refit
8.Locate the flywheel on the crankshaft and
secure with new patched retaining bolts,
progressively tighten to
147 Nm.
9.Check the flywheel for possible run-out by
mounting a dial test indicator with the stylus in a
loaded condition resting on the flywheel face at a
radius of 114mm from the centre.
10.Turn the flywheel and check that run-out does
not exceed 0,05 to 0,07mm. Should run-out be
excessive, remove the flywheel and check again
for irregularities on the crankshaft and flywheel
mating faces and the dowel.
11.Reverse removal procedure. 1 to 6.

Tdi
15
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
NOTE: The crankshaft rear oil seal is
retained in its own housing, if the seal
requires replacing the housing and seal
assembly (1) must be renewed complete with the
housing seal (3). Housing and seal assemblies are
supplied with their own former/seal guide (2)
already fitted. This former must not be removed
before fitting the assembly to the engine. If a seal
and housing assembly is received without a
former/guide fitted it must be returned to the
supplier. Used formers/guides must be discarded
immediately after use, under no circumstances
should they be reused on other assemblies.
1.Disconnect battery negative lead.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
Assembly
4.Remove flywheel.See Flywheel
5.Remove five bolts and withdraw seal housing
and seal assembly complete with gasket.
Refit
6.Insert slave studs to seal housing mounting face.
7.Position new seal housing gasket over slave
studs and crankshaft flange onto cylinder block.

12ENGINE
16
REPAIR 8.Ensure housing seal is correctly seated in its
groove in new housing and seal assembly.
9.Fit new assembly, with former/guide in-situ, over
crankshaft flange, this action will eject
former/guide.
10.Secure assembly to cylinder block with five bolts
tightened to correct torque, removing slave studs
individually and inserting bolts.
11.Refit flywheel.
See Flywheel
12.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
13.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
14.Reconnect battery negative lead.CRANKSHAFT BEARING BUSH
Service repair no - 12.21.45
1.Disconnect battery negative lead.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
Assembly
4.Remove flywheel.See Flywheel
5.Remove bearing bush.
NOTE: The bearing bush can be removed
by using one of the following methods.
Method 1.
Obtain a short length of steel rod of a diameter having
a good slide fit in the bore of the bush. Pack the bore
with grease and insert the steel rod into the end of the
bore, give a sharp blow with a hammer and the
grease should drive out the bush. It is recommended
that the bush and rod be covered by a suitable cloth
or rag to prevent grease from splashing.

Tdi
17
REPAIR Method 2.
Thread the bore of the existing bush and using a
suitable bolt extract the bush. Thoroughly clean bush
location ensuring all swarf is removed.
Fitting
6.Fit new bush using a suitable shouldered drift,
inserting bush flush with end of crankshaft.
7.Refit flywheel.
See Flywheel
8.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
9.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
10.Reconnect battery negative lead.FLYWHEEL HOUSING
Service repair no - 12.53.01
Remove
1.Disconnect battery negative lead.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
Assembly
4.Remove flywheel.See Flywheel
5.Remove starter motor.
6.Remove two bolts from top of flywheel housing.
7.Remove four bolts from bottom of flywheel
housing.
8.Remove six inner bolts and lift off flywheel
housing.
Refit
9.Clean rear face of housing and mating face on
block, ensuring all old sealant is removed.

12ENGINE
18
REPAIR 10.Apply sealant to flywheel housing mating face on
cylinder block (Fig. J5944).
11.Fit housing to cylinder block and secure with
bolts as removed. Tighten to
45 Nm.
12.Remove surplus sealant from block.
13.Refit starter motor.
14.Refit flywheel.
See Flywheel
15.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
16.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
17.Reconnect battery negative lead.OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under filter.
2.Unscrew filter anti-clockwise, using a strap or
spanner.
Refit
3.Smear clean engine oil on seal of new filter.
4.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. Do not over tighten.

Tdi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

12ENGINE
10
REPAIR TIMING CHAIN AND CHAINWHEELS
Service repair no - 12.65.12
Remove
1.Remove front cover.
See Front Cover Gasket
2.Remove retaining bolt and washer, remove
distributor drive gear and spacer.
3.Ensure number one piston is at TDC.
4.Remove chainwheels and chain as an assembly.
See V8i Overhaul Manual.
Refit
5.Clean chainwheels and chain.
6.Fit chainwheels to chain, aligning timing marks.
7.Ensure camshaft key is fitted parallel to shaft
axis to ensure adequate lubrication to distributor
drive gear.
8.Engage chainwheel assembly on camshaft and
crankshaft keys, ensure chain wheels are fully
located.
9.Check alignment of timing marks with straight
edge.
10.Fit spacer with flange to front,
11.Fit distributor drive gear with groove towards
spacer.
12.Fit retaining bolt and washer. Tighten to
58 Nm.
13.Fit front cover.See Front Cover Gasket
FLYWHEEL
Service repair no - 12.53.07
Remove
1.Remove gearbox and clutch.
See CLUTCH,
Repair, Clutch Assembly
2.Loosen starter motor bolts.
3.Lock flywheel, remove flywheel bolts and
flywheel.
Refit
4.Clean components for reassembly.
5.Fit flywheel.
6.Clean threads, apply Loctite 270 to threads.
7.Lock flywheel, fit flywheel bolts. Tighten to
80
Nm.

12ENGINE
14
REPAIR
39.Remove remaining bell housing to cylinder block
bolts.
40.Remove starter motor ground strap from
chassis.
41.Remove stands and lower vehicle.
42.Position hydraulic trolley jack under bell housing
to support gearbox when engine and gearbox
are separated.
43.Fit lifting chains to engine. Carefully raise hoist a
little, ease engine and gearbox apart, steady
engine on hoist.
44.Ensure no components remain that will prevent
engine being removed.
45.Slowly raise engine clear of engine
compartment. Move engine away from vehicle
and place on a suitable engine stand.
Refit
46.Fit lifting chains to engine. Raise engine using
hoist.
47.Lower engine into engine compartment. Ensure
all components are clear of engine assembly.
48.Automatic vehicles: With assistance, manoeuvre
engine until bottom two engine and bellhousing
bolt holes align. Ensure that two cylinder block
dowels locate in bell housing.
Manual vehicles: Lower engine into position.
Locate primary pinion into clutch. Engage bell
housing dowels.
49.Fit two bolts and partially tighten.
50.Remove jack and lower hoist until engine rests
securely on engine mounting brackets.
51.Fit top two bell housing securing bolts. Tighten
to
40 Nm.
52.Fit remaining bell housing to cylinder block bolts.
Tighten to
40 Nm.
53.Automatic vehicles: With assistance, rotate
crankshaft pulley, line up marked holes in drive
plate and torque converter. Fit two bolts.
Tighten to
40 Nm.
54.Rotate crankshaft 180°and fit remaining two
bolts tighten to correct torque,
40 Nm.
55.Fit new gasket and refit bottom cover, tighten
bolts to
9 Nm.
56.Fit new exhaust flange gaskets, fit exhaust to
manifold.
57.Refit all harnesses, ground straps breather pipes
and hoses at rear of engine.
58.Raise engine and refit engine mounting rubbers,
tighten nuts to
20 Nm.
59.Remove temporary lifting eye ETC 5964 and
reverse instructions 1 to 23, ensuring that all
electrical plugs and harnesses are fitted in
correct locations.

Mpi
5
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1.Remove gearbox.
2.Remove clutch assembly.
3.Remove flywheel.
4.Drain engine oil.
5.Fit sump plug, replacing sealing washer if
damaged and tighten to the correct torque.
6.Loosen 15 sump bolts by approximately 3 turns,
allowing sump to drop away from rear oil seal
housing. Do not loosen 3 boltsAaround oil
pump housing.
7.Remove bolts securing oil seal housing, remove
seal and housing assembly.
Refit
1.Clean seal seating area of block and accessible
area of sump gasket. Sump gasket must be
replaced if damaged.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-061 over crankshaft boss and fit
oil seal and housing assembly.
4.Remove tool.
5.Fit and tighten seal housing bolts to correct
torque in sequence shown.
10Nm
6.Tighten sump bolts to correct torque and in the
correct sequence.
See Engine Sump Gasket
7.Fit flywheel.
8.Fit clutch assembly.
9.Fit gearbox.