clock LAND ROVER DISCOVERY 1995 Owner's Guide

76CHASSIS AND BODY
46
REPAIR DASH PANEL CENTRAL LOUVRE PANEL
Service repair no - 76.46.42
Remove
1.Disconnect battery negative lead.
2.Remove radio.
See ELECTRICAL, Repair,
radio.
3.Release tags securing radio cage to louvre
panel and remove cage.
4.Remove clock.
See ELECTRICAL, Repair,
clock.
5.Release 4 coin tray securing tags.
6.Remove coin tray.
7.Remove 3 heater control and blower switch
knob.
8.Remove 2 screws securing heater graphic
display panel and remove panel.
9.Remove 4 screws securing heater control unit to
panel.
10.Working through coin tray aperture, remove
screw securing panel.
11.Working through clock aperture, remove screw
securing panel.
12.Loosen 2 uppermost panel retaining screws.
NOTE: On some models the panel is fitted
with an LED. In this case, manoeuvre LED
from panel and disconnect.
13.Remove panel retaining screw cover.

CHASSIS AND BODY
47
REPAIR
14.Remove 2 screws securing louvre panel.
15.Remove louvre panel from dash panel.
Refit
16.Position louvre panel, feed harness connectors
through their correct apertures,and align to dash
panel.
CAUTION: When refitting avoid trapping of
electrical wiring.
17.Fit and tighten screws securing louvre panel.
18.Fit panel retaining screw cover.
19.Position heater control unit to panel and secure
with screws.
20.Fit heater graphic display panel and secure with
screws.
21.Fit heater control and blower switch knobs.
22.Fit clock.
See ELECTRICAL, Repair, clock.
23.Position coin tray and secure to tags.
24.Position radio cage, feed electrical connectors
and aerial through cage, and position to panel.
25.Bend back radio cage retaining tags.
26.Fit radio.
See ELECTRICAL, Repair, radio.
27.Connect battery negative lead.DASH PANEL ASSEMBLY
Service repair no - 76.46.23
Remove
1.Move front seats to rearmost position.
2.Disconnect battery negative lead.
3.Disconnect air bag multiplugs under dash panel.
CAUTION: When air bags are fitted,
reference must be made to the Airbag
Supplementary Restraint System section.
4.Remove passenger glove box.
5.Remove driver's side access panel.
6.Remove centre console assembly.
See centre
console.
7.Remove airbag from steering wheel.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, driver's airbag module.
8.Remove passenger's airbag from dash panel.
See SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, passenger's airbag module.
9.Release clamp and lower steering column.
10.Remove steering wheel.
See STEERING,
Repair, steering wheel.
11.Remove column switch.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, column switch assembly.
12.Remove instrument binnacle.See
ELECTRICAL, Repair, instrument binnacle.
13.Remove radio.See ELECTRICAL, Repair,
radio.
14.Remove exterior mirrors switch panel.
15.Remove coin tray.
16.Remove switch panel.
17.Remove clock.
18.Undo screw securing mounting bracket and
position passenger's side relay assembly aside.
19.Set heater controls fully clockwise.

HEATING AND VENTILATION
3
REPAIR Air direction
3.Set control fully clockwise
4.Release outer cable from 2 clips on unit.
5.Release cable from stud on flap lever.
6.Remove control cable from control lever.
Temperature
7.Set RH control fully clockwise, LH control fully
anti-clockwise
8.Release outer cable from 2 clips on unit.
9.Release cable from stud on flap lever.
10.Remove control cable from control lever.
Refit
11.Reverse removal procedure. Check the
satisfactory function of the controls before fitting
louvre vent panel.RESISTOR UNIT
Service repair no - 80.20.17
Remove
1.Open glove box, manoeuvre side springs
through cut-outs and lower lid.
2.Remove 2 screws securing resistor unit to
trunking.
3.Disconnect multiplug and remove resistor unit.
Refit
4.Reverse removal procedure.

84WIPERS AND WASHERS
4
REPAIR WIPER BLADES
Service repair no - 84.15.05
Remove
1.Pull wiper blade away from screen.
2.Depress spring clip and withdraw blade from
hooked end of wiper arm.
Refit
3.Reverse removal procedure. 1 and 2.REAR WINDOW WASHER JET
Service repair no - 84.30.09
Remove
1.Turn washer jet in a clockwise direction to
release it from the rear quarter panel.
2.Remove rear quarter/speaker trim panel.
3.Feed washer tubing through rear quarter panel
to allow removal of washer jet.
4.Remove washer jet from tubing.
Refit
5.Reverse removal procedure. 1 to 4.
NOTE: The tubing run from the reservoir to
rear door washer jet differs between left
and right hand drive vehicles. On right
hand vehicles the tubing run is on the left hand
side of the roof. On left hand drive vehicles, the
right side.
See Description and operation,
Windscreen Wiper and Washer Operation

86ELECTRICAL
6
REPAIR Refit
NOTE: If a new distributor is being fitted,
mark body in same relative position as
distributor removed.
8.Leads for distributor cap should be connected as
illustrated.
Figures 1 to 8 inclusive indicate plug lead
numbers.
RH-Right hand side of engine, when viewed
from rear.
LH-Left hand side of engine, when viewed from
rear.
9.If engine has not been turned while distributor
has been removed, carry out instructions 10. to
17. Alternatively proceed to instruction 18.
10.Fit new 'O' ring seal to distributor housing.
11.Turn distributor drive until centre line of rotor arm
is 30Ê anti-clockwise from mark made on top
edge of distributor body.
12.Fit distributor in accordance with alignment
markings.
NOTE: It may be necessary to align oil
pump drive shaft to enable distributor
drive shaft to engage in slot.
13.Fit clamp and bolt. Secure distributor in exact
original position.
14.Connect vacuum hose to distributor and low
tension lead to coil.
15.Fit distributor cap.
16.Reconnect battery.
17.Using suitable electronic equipment, set ignition
timing.
See Adjustment, Ignition timing
18.If engine has been turned with distributor
removed, carry out instructions 19 to 30.
19.Set engine-No. 1 piston to static ignition timing
figure
See ENGINE TUNING DATA,
Information, Engine 3.9 V8i
20.Turn distributor drive until rotor arm is
approximately 30Ê anti-clockwise from number
one sparking plug lead position on cap.
21.Fit distributor to engine.
22.Check that centre line of rotor arm is now in line
with number one sparking plug lead on cap.
Reposition distributor if necessary.
23.If distributor does not seat correctly in front
cover, oil pump drive is not engaged. Engage by
lightly pressing down distributor while turning
engine.
24.Fit clamp and bolt, do not tighten.
25.Set ignition timing statically to 6Ê B.T.D.C.
26.Connect vacuum hose to distributor.
27.Fit low tension lead to coil.
28.Fit distributor cap.
29.Reconnect battery.
30.Using suitable electronic equipment set the
ignition timing.
See Adjustment, Ignition
timing

86ELECTRICAL
16
REPAIR SIDELIGHT BULB
Service repair no - 86.40.33
Remove
1.Remove headlight,
See Headlight
2.Disengage bulb holder by twisting a quarter turn
anti-clockwise.
3.Withdraw bulb from holder.
Refit
4.Reverse removal procedure.FRONT DIRECTION INDICATORS
Service repair no - 86.40.41
Remove
1.Pull spring clips, release from location and lift out
direction indicator unit.
2.Turn bulb holder anti-clockwise to release from
indicator unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure. When replacing
light unit, locate the two lugs at the bottom of the
lens before re-engaging spring clips.

ELECTRICAL
17
REPAIR REAR LIGHT UNIT
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Disconnect wiring harness multi-plug from light
unit.
4.Remove retaining nuts and withdraw light unit
from rear of vehicle.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure. Ensure that the
rubber seal is seated correctly.STOP, REVERSING, FOG GUARD BULBS
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Turn bulb holder anti-clockwise to release.
4.Remove bulb.
NOTE: On vehicles fitted with rear air
conditioning remove access panel
housing rear loadspace light to gain
access.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure.

86ELECTRICAL
18
REPAIR REAR LIGHTS, BUMPER MOUNTED
Service repair no - 86.41.42
Remove
1.From behind bumper disconnect light plugs.
2.Unscrew two retaining nuts and remove light unit
from bumper.
Refit
3.Reverse removal procedure.
NOTE: The black lead plug fits into the
direction indication light, the white lead
plugs into the tail light, the bulb holder
being colour coded red.DIRECTION INDICATOR, TAIL LIGHT BULBS
Service repair no - 86.41.43
Remove
1.Turn bulb holder anti-clockwise to release from
light unit.
2.Push and twist the bulb to remove.
Refit
3.Reverse removal procedure.

86ELECTRICAL
20
REPAIR HIGH MOUNTED STOP LIGHT
Service repair no - 86.41.35
Remove
1.Remove two screws and lift off light reflector
body.
2.Unscrew retaining nut and remove lens unit from
rear door glass.
Refit
3.Reverse removal procedure.STOP LIGHT BULB
Service repair no - 86.40.87
Remove
1.Remove reflector body.
2.Turn bulb holder anti-clockwise to release from
light unit.
3.Push and twist the bulb to remove.
Refit
4.Reverse removal procedure.

86ELECTRICAL
22
REPAIR SIDE REPEATER LIGHT
Service repair no - 86.50.59
Remove
1.Push the lens to the right and then pull outward
to detach lens and bulb holder from the panel.
2.Turn lens anti-clockwise and remove from bulb
holder.
3.Pull bulb from holder.
Refit
4.Reverse removal procedure.BUMPER MOUNTED SIDE LIGHT
Service repair no - 86.50.59
Remove
1.From behind bumper turn holder anti-clockwise
and release from light unit.
2.Pull bulb from holder.
Refit
3.Reverse removal procedure.