oil LAND ROVER FREELANDER 2001 Workshop Manual

AIR CONDITIONING
REPAIRS 82-9
9.Remove 3 bolts securing compressor to
mounting bracket.
10.Release compressor from mounting bracket
and remove from under vehicle.
11.Drain oil from old compressor and record the
amount drained.Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.

+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Ensure mating faces of A/C pipes and
compressor are clean.
4.Lubricate new A/C pipe 'O' rings with clean
refrigerant oil.

+ GENERAL DATA, Air Conditioning.
5.Fit 'O' rings to A/C pipes.
6.Fit A/C compressor to mounting bracket. Fit
and tighten bolts to 25 Nm (18 lbf.ft).
7.Position compressor mounting bracket, fit bolts
and tighten to 25 Nm (18 lbf.ft).
8.Connect A/C compressor multiplug.
9.Fit alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - K1.8.
10.Replace receiver drier.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
11.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
12.Remove stands and lower vehicle.
13.Connect battery earth lead.
14.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
M82 0731

AIR CONDITIONING
REPAIRS 82-11
11.Remove 2 bolts securing A/C pipes to
condenser and release pipes from condenser.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
12.Remove and discard 'O' rings from A/C pipes.
13.Remove condenser.
14.Remove 8 screws, securing 4 mounting
brackets to condenser and move aside.
15.Remove and discard receiver drier, plug
connections.Refit
1.Fit condenser mounting brackets, fully tighten
LH screws. Leave RH screws loose until
receiver drier is fitted.
CAUTION: Ensure that bolts of the correct
length are used on refit.
2.Lubricate new 'O' rings with clean refrigerant
oil, fit one seal to each condenser pipe.
3.Position A/C pipes to condenser, fit bolts and
tighten to 8 Nm (6 lbf.ft).
4.Fit bolts securing condenser to radiator and
tighten to 8 Nm (6 lbf.ft).
5.Fit receiver drier assembly to condenser.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
6.Fit air deflectors and secure with scrivets.
7. Up to 04MY: Position armature, fit and tighten
4 nuts and bolts securing armature to body to
25 Nm (18 lbf.ft).
8. 04MY on: Position armature, fit bolts securing
armature to crash cans and tighten to 25 Nm
(18 lbf.ft).
9. KV6 models:Align PAS fluid cooler and tighten
bolts to 8 Nm (6 lbf.ft).
10.Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11. Td4 models: Fit intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
12.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
13.Connect battery earth lead.
M82 0706

AIR CONDITIONING
REPAIRS 82-13
Refit
1.Lubricate new 'O' rings, dust shield and
condenser thread with refrigerant oil.
2.Fit 'O' rings and dust shield to receiver drier.
CAUTION: Do not remove receiver/dryer
from packaging until immediately before
installation.
3.Fit receiver drier to condenser and tighten to 12
Nm (9 lbf.ft).
4.Tighten clamps securing receiver drier to
condenser.
5.If fitted, fit air deflector and secure with scrivets.
6. Td4 models: Fit intercooler.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Intercooler.
7. Up to 04MY: Position armature, fit and tighten
4 nuts and bolts securing armature to body to
25 Nm (18 lbf.ft).
8. 04MY on: Position armature, fit bolts securing
armature to crash cans and tighten bolts to 25
Nm (18 lbf.ft).
9. KV6 models: Align PAS fluid cooler and
tighten bolts to 8 Nm (6 lbf.ft).
10.Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
11.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
12.Connect battery earth lead.
Switch - control
$% 82.20.07
Remove
1.Remove radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.
2.Remove 3 heater control knobs.
3.Remove 2 screws securing heater control
finisher to heater controls and remove finisher.
4.Disconnect multiplug from A/C control switch.
5.Remove switch from heater controls.
Refit
1.Fit A/C control switch and connect multiplug.
2.Fit heater control finisher and secure with
screws.
3.Fit heater control knobs.
4.Fit radio.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio - up to 04MY.

AIR CONDITIONING
REPAIRS 82-15
Valve - thermostatic expansion (TXV)
$% 82.25.01
Remove
1.Disconnect battery earth lead.
2.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
3.Remove bolt securing A/C pipes to TXV,
disconnect pipes and discard 'O' rings. Plug A/
C connections.
WARNING: Under no circumstances should
refrigerant hoses be disconnected without
first discharging the system.4.Remove 2 Allen screws securing TXV to
bulkhead, withdraw assembly and discard 'O'
rings.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
Refit
1.Clean mating faces and seal recesses on
evaporator, TXV and block and pipe assembly.
2.Lubricate new 'O' rings with clean refrigerant oil
and fit to TXV pipes.
3.Fit block and pipe assembly to TXV and tighten
bolts to 5 Nm (3.5 lbf.ft).
4.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
5.Connect battery earth lead.

AIR CONDITIONING
REPAIRS 82-17
12.Remove evaporator from casing.
13.Remove 2 Allen key bolts securing TXV valve,
remove valve and discard 2 'O' rings.
Refit
1.Lubricate new 'O' rings with clean refrigerant oil
and fit to evaporator pipes
2.Fit evaporator pipes to TXV valve and fit
bracket, fit and tighten bolt to 10 Nm (7 lbf.ft).
3.Carefully fit evaporator to casing.
4.Fit top half of evaporator casing.
5.Fit 7 screws to casing.
6.Fit harness in securing clips.
7.Locate evaporator assembly to drain hose and
air intake, position evaporator to body.
8.Fit and tighten nuts securing evaporator to
body.
9.Connect multiplugs to heater harness and A/C
switches.
10.Position face level vent ducting, fit and tighten
bolt.
11.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
12.Clean evaporator pipes.
13.Lubricate new 'O' rings with refrigerant oil.
14.Fit 'O' rings to evaporator pipes.
15.Clean evaporator pipes.
16.Fit pipes to TXV valve and fit bracket, tighten
bolt to 10 Nm (7 lbf.ft).
17.Charge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
M820825

CHARGING AND STARTING
ADJUSTMENTS 86-1-1
CHARGING AND STARTING ADJUST ME NTS
Ancillary drive belt - K1.8
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Apply a force of 10 kg to drive belt at position 'X'
and measure deflection between crankshaft
pulley and alternator pulley. Deflection must be
6 - 8 mm.Adjust
1.Loosen alternator pivot nut and bolt.
2.Loosen bolt securing alternator adjustment
bracket to engine.
3.Loosen bolt securing alternator to adjustment
bracket.
4.Increase drive belt tension by rotating
alternator adjustment bolt clockwise.
5.Tighten alternator pivot and adjustment bracket
bolts to 25 Nm (18 lbf.ft).
6.Recheck drive belt tension.
7.Fit splash shield and secure with bolts.
8.Straighten steering.
9.Connect battery earth lead.

CHARGING AND STARTING
86-1-2 ADJUSTMENTS
Ancillary drive belt - K1.8 with A/C
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Check belt length, belt must be renewed before
indicator reaches RH end of slot.
6.Fit splash shield and secure with bolts.
7.Straighten steering.
8.Connect battery earth lead.

CHARGING AND STARTING
REPAIRS 86-1-3
REPAIRS
Alternator - Td4
$% 86.10.02
Remove
1.Disconnect battery earth lead.
2.Drain cooling system.

+ COOLING SYSTEM - Td4,
ADJUSTMENTS, Coolant - drain and refill.
3. Models with A/C: Remove compressor drive
belt.

+ AIR CONDITIONING, REPAIRS,
Drive belt - compressor - Td4.
4.Remove 3 bolts securing coolant rail to sump
and cylinder block.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.
5. Models with A/C: Loosen bolt securing
compressor support bracket to sump, do not
remove.
6. Models with A/C: Remove 3 bolts securing
compressor to mounting bracket, release
support bracket and tie compressor aside.7. Models with A/C: Remove 3 bolts and bracket,
securing compressor mounting to casting on
cylinder block.
8.Disconnect alternator multiplug.
9.Remove nut securing battery cable to alternator
and remove cable.
10.Remove 3 bolts and remove alternator.
M86 5309
M86 5311

CHARGING AND STARTING
REPAIRS 86-1-11
Tensioner - ancillary drive belt - Td4
$% 86.10.06
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
4.Remove ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Remove bolt securing dipstick tube to oil filter.
6.Move dipstick tube aside for access.
7.Remove alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - Td4.
8.Manoeuvre engine to suitable working height.9.Remove Allen bolt securing ancillary belt idler
and remove idler from vehicle.
10.Remove nut, securing ancillary drive belt
tensioner arm to rear of spring housing.
11.Rotate belt tensioner arm through 180° to clear
chassis side member and remove from timing
cover.
M86 5302
M86 5303

CHARGING AND STARTING
86-1-12 REPAIRS
12.Remove and discard tensioner arm seal.
13.Remove 2 bolts from timing cover, securing
ancillary drive belt tensioner.
14.Remove tensioner.
Refit
1.Clean tensioner block and mounting.
2.Position tensioner block, temporarily fit
tensioner arm to align spring block with timing
cover. Fit bolts and tighten to 25 Nm (18 lbf.ft).
Remove tensioner arm.
3.Clean seal mounting for tensioner arm on
timing cover, fit new seal.
4.Fit ancillary drive belt tensioner arm to timing
cover, turn through 180° to align with tensioner
spring housing, push fully home. Fit and tighten
nut to 10 Nm (7.5 lbf.ft).
5.Fit alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - Td4.
6.Fit idler pulley to mounting and tighten Allen
bolt to 25 Nm (18 lbf.ft).
7.Position dipstick tube to oil filter, fit bolt and
tighten to 10 Nm (7.5 lbf.ft).
8.Fit ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
9.Fit hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
10.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
11.Connect battery earth lead.
Battery
$% 86.15.01
Remove
1.Disconnect both battery terminals, earth lead
first.
2.Remove bolt and battery clamp.
3.Remove battery.
Refit
1.Clean battery tray.
2.Fit battery and clamp, tighten bolt to 12 Nm (9
lbf.ft).
3.Apply petroleum jelly to both terminals, fit and
tighten terminal bolts negative lead last.