oil LAND ROVER FREELANDER 2001 Workshop Manual

DRIVESHAFTS
REPAIRS 47-7
10.With assistance pull hub assembly outwards
and release drive shaft outer joint from hub
assembly.
11.Taking care not to damage 'Flinger', release
drive shaft inner joint from differential using
LRT-51-014 and remove drive shaft.
12.Remove and discard drive shaft circlip.Refit
1.Inspect differential seal, renew if worn or
damaged.
2.Clean ends of drive shaft and locations in hub
and differential.
3.Lubricate oil seal running surface with
transmission oil.
4.Fit new circlip to drive shaft.
5.Fit drive shaft to differential and push fully
home.
CAUTION: Pull the drive shaft to ensure the
circlip is fully engaged and retains the shaft.
6.With assistance fit drive shaft to hub.
7.Fit new drive shaft nut but do not tighten at this
stage.
8.Fit nut, bolt and dynamic damper to adjustable
transverse link and tighten to 120 Nm (89 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with the weight of the vehicle on the
suspension.
9.Fit nut and bolt to fixed transverse link and
tighten to 120 Nm (89 lbf.ft).
10.Fit spacer, nut and bolt to trailing link and
tighten to 120 Nm (89 lbf.ft).
11.Fit new drive shaft nut and tighten to 400 Nm
(295 lbf.ft). Stake nut to shaft.
12.Check and top up oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
13.Fit road wheel(s) and tighten nuts to 115 Nm 85
lbf.ft).
14.Remove stands and lower vehicle.
15.Connect battery earth lead.

REAR AXLE & FINAL DRIVE
REPAIRS 51-1
REAR AXLE & FINA L D RIVE REPAIRS
Differential assembly
$% 51.15.01
Remove
1.Remove both drive shafts.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - RH.
2.Reference mark rear propeller shaft for
reassembly.
3.Position container to catch oil spillage
4.Remove 4 nuts and bolts securing propeller
shaft to differential. Release propeller shaft and
tie aside.
5.Support weight of differential assembly on a
jack.
6.Remove 2 bolts securing differential to front
mounting.7.Depress red locking collar and disconnect
breather pipe from differential casing.
8.Remove 4 bolts securing differential assembly
to rear mountings.
9.With assistance, rotate differential assembly
through 90° and remove from subframe.

REAR AXLE & FINAL DRIVE
51-2 REPAIRS
Refit
1.With assistance position differential assembly
to subframe and locate in mountings, fit bolts
but do not tighten at this stage.
2.Position centralising jig LRT-51-013 to align
differential assembly.
3.Tighten forward bolts to 65 Nm (48 lbf.ft).
4.Tighten rearward bolts to 65 Nm (48 lbf.ft).
5.Remove LRT-51-013.
6.Connect breather pipe.
7.Position propeller shaft to rear axle and align
reference marks.
8.Fit and tighten nuts and bolt securing propeller
shaft to rear axle to 65 Nm (48 lbf.ft).
9.Fit drive shafts.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - LH.

+ DRIVESHAFTS, REPAIRS, Shaft
with both joints - RH.
10.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
Cover - rear - differential
$% 51.15.04
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Position container to catch oil spillage.
3.Remove oil level plug.
4.Remove 10 bolts securing rear cover to
differential casing.
5.Remove rear cover.
Refit
1.Clean rear cover, mating face on differential
and sealant from bolts and bolt threads.
2.Apply sealant, Part No. STC 3811 to casing
and fit rear cover.
3.Apply sealant, Part No. STC 50552 to threads
of rear cover bolts.
4.Fit rear cover bolts bolts and tighten by
diagonal selection to 25 Nm (18 lbf.ft).
5.Fill differential with oil.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
6.Fit level plug and tighten to 27 Nm (20 lbf.ft).
7.Remove stands and lower vehicle.

REAR AXLE & FINAL DRIVE
REPAIRS 51-5
Oil seal - pinion
$% 51.20.01
Remove
1.Release both drive shafts from differential
assembly.

+ REAR AXLE & FINAL DRIVE,
REPAIRS, Oil seal - differential housing.
2.Reference mark propeller shaft and pinion
flanges to aid reassembly.
3.Remove 4 nuts and bolts securing propeller
shaft to differential. Release propeller shaft and
tie aside.
4.Check and record the torque required to rotate
the pinion and differential.
CAUTION: Drive shafts must be removed to
obtain correct torque to turn figure.
5.Using LRT-51-003 to restrain differential
flange, remove nut and washer securing pinion
flange. Discard nut.6.Remove pinion flange.
7.Carefully remove and discard oil seal, take care
not to damage oil seal recess.
8.Remove oil thrower.
9.Remove pinion bearing inner race.
10.Remove and discard collapsible spacer.

REAR AXLE & FINAL DRIVE
51-6 REPAIRS
Refit
1.Fit new collapsible spacer.
2.Fit pinion bearing and oil thrower.
3.Clean pinion flange and oil seal recess.
4.Fit new oil seal using LRT-51-010.
5.Fit pinion flange and washer.
6.Restrain pinion flange using LRT- 51-003.
7.Fit new pinion nut and tighten to 190 Nm (140
lbf.ft).
8.Check for end float on pinion. If end float exists
continue to tighten pinion nut until end float is
removed.
9.Continue to tighten pinion nut until correct
preload is obtained.
10.Pinion preload is 1.7 - 2.8 Nm (1.2 - 2.1 lbf.ft), if
higher replace collapsible spacer.
CAUTION: Do not tighten pinion nut to more
than 373 Nm (275 lbf.ft), or the collapsible
spacer will compress too far.
11.Clean propeller shaft flange and mating face.
12.Position propeller shaft to rear axle and align
reference marks.
13.Tighten propeller shaft nuts and bolts to 65 Nm
(48 lbf.ft).
14.Fit drive shafts.

+ REAR AXLE & FINAL DRIVE,
REPAIRS, Oil seal - differential housing.
15.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
Oil seal - differential housing
$% 51.20.36
Remove
1.Raise rear of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove road wheel.
3.Remove bolt securing handbrake cable to
subframe.
4.Remove nut and bolt securing trailing link to
rear hub, collect spacer from under bolt head.
5.Remove nut and bolt securing fixed transverse
link to subframe. Collect dynamic damper.
6.Remove nut and bolt securing adjustable
transverse link to subframe.
7.Position drain tin to catch oil spillage.
8.With assistance pull hub assembly outwards.

REAR AXLE & FINAL DRIVE
REPAIRS 51-7
9.Taking care not damage oil seal 'flinger',
release drive shaft from differential using LRT-
51-014 and position shaft aside.
10.Remove and discard circlip from drive shaft.
11.Remove differential oil seal.Refit
1.Clean drive shaft oil seal recess in axle casing.
2.Fit new oil seal using LRT-51-012.
3.Clean end of drive shaft and location in
differential.
4.Check condition of oil seal 'Flinger', renew if
damaged.
5.Fit new circlip to drive shaft.
6.With assistance fit drive shaft to differential,
push drive shaft fully home to engage circlip.
7.Fit nut and bolt to fixed transverse link and
tighten to 120 Nm (89 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
8.Fit nut, bolt and dynamic damper to adjustable
transverse link and tighten to 120 Nm (89 lbf.ft).
9.Fit spacer, nut and bolt to trailing link and
tighten to 120 Nm (89 lbf.ft).
10.Fit bolt securing handbrake cable clip and
tighten to 22 Nm (16 lbf.ft).
11.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
12.Check differential oil level.

+ MAINTENANCE, MAINTENANCE,
Rear Axle.
13.Remove stands and lower vehicle.

STEERING
REPAIRS 57-9
Oil cooler - Td4 & K1.8 models
$% 57.15.11
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover if fitted.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
3. Td4 models: Release and remove air intake
duct.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
4. Td4 models: Loosen 2 clips and remove
intercooler outlet hose.
5. Td4 models: Remove dipstick for access.
CAUTION: Always fit plugs to open
connections to prevent contamination.
6.Remove bolt securing PAS oil cooler pipe lower
mounting bracket to body.
7.Remove bolt securing PAS oil cooler pipe to RH
suspension turret.8.Place a suitable container beneath PAS
reservoir, release clip and disconnect return
hose from mount. Allow fluid to drain.
9.Place container beneath PAS quick release
pipe fitting.
10.Clean area surrounding quick release
connection.
11.Using LRT-57-044, disconnect cooler quick
release hose.
12.Release PAS reservoir from mounting bracket
and move aside.
13.Remove PAS oil cooler from vehicle.
NOTE: Do not carry out further dismantling if
component is removed for access only.

M12 6972

M57 1047

STEERING
57-10 REPAIRS
14.Remove clips from PAS oil cooler.
Refit
1.Clean cooler mounting points.
2.Fit clips to PAS cooler.
3.Fit PAS oil cooler to vehicle.
4.Connect quick release pipe fitting.
5.Align PAS pipe bracket, fit bolt and tighten to 10
Nm (7 lbf.ft).
6.Fit bolt to clip securing PAS pipe to RH turret,
tighten to 10 Nm (7 lbf.ft).
7.Fit PAS reservoir to mounting bracket.
8.Clean PAS fluid reservoir around filler cap and
fluid level indicators.
9.Fit PAS return hose to reservoir and secure
clip.
10. Td4 models: Fit intercooler outlet hose and
tighten clips.
11. Td4 models: Fit intake duct to body and duct
assembly.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Ducting - intake assembly.
12. Td4 models: Fit engine oil dipstick.
13. Fit engine acoustic cover if fitted.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
14.Connect battery earth lead.
15.Bleed PAS system.

+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
Oil cooler - KV6 models
$% 57.15.11
Remove
1.Remove front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
2.Position container below PAS pipes to catch
fluid spillage.
3.Using LRT-57-044 release and disconnect
PAS hoses from oil cooler.
4.Remove 2 bolts and remove PAS fluid cooler.
Refit
1.Fit fluid cooler and tighten bolts to 10 Nm (7
lbf.ft).
2.Clean connections.
3.Connect hoses to fluid cooler.
4.Fit front bumper.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5.Bleed PAS system.

+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
M57 1204
LRT-57-044

STEERING
REPAIRS 57-15
Pump - steering - Td4
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
3.Loosen 3 PAS pump pulley bolts.
4.Remove ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Raise engine on hoist.
6.Remove bolts and remove PAS pump pulley.
7.Cover alternator to prevent PAS oil
contamination.
8.Place container beneath PAS pump, release
clip and remove feed hose to pump. Allow fluid
to drain.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.9.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
10.Remove 4 bolts and remove PAS pump.
11.Remove 5 Torx bolts securing PAS pump to
mounting brackets. Collect mounting brackets.
Refit
1.Position PAS pump to mounting brackets, fit
and tighten Torx bolts to 25 Nm (18 lbf.ft).
2.Position pump to mounting, fit bolts and tighten
M8 bolts to 25 Nm (18 lbf.ft) and M6 bolts to 10
Nm (7.5 lbf.ft).
3.Using new sealing washers, fit PAS outlet hose
to pump and tighten banjo bolt to 25 Nm (18
lbf.ft).
4.Clean PAS pump and mating faces.
5.Fit inlet hose to PAS pump and secure with new
clip.
6.Fit PAS pump pulley to PAS pump and tighten
bolts to finger tight.
7.Fit ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
8.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
9.Fit hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
10.Connect battery earth lead.

STEERING
57-16 REPAIRS
Nacelle - column
$% 57.40.29
Remove
1.Remove key from starter switch.
2.Carefully remove upper half of nacelle. Take
care when releasing clips from lower half of
nacelle.
3.Remove 2 screws securing lower nacelle to
steering column.
4.Lower steering column tilt lever.
5.Carefully remove cover from starter switch
being careful not to damage the passive coil.
6.Carefully pull lower half of nacelle from
retaining clip on column lockRefit
1.Ensure that the steering column tilt lever is
lowered.
2.Position lower half of nacelle and engage with
clip on column lock.
3.Raise column tilt lever.
4.Fit and tighten 2 screws securing lower half of
nacelle to steering column.
5.Fit cover to starter switch.
6.Fit upper half of nacelle and ensure that clips
engage with lower half.