length LAND ROVER FREELANDER 2001 Owner's Manual

EXTERIOR FITTINGS
REPAIRS 76-2-17
Moulding - roof - 5 door
$% 76.43.68
Remove
1.Remove tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
2.Remove roof finisher caps or roof rack side rail.

+ EXTERIOR FITTINGS, REPAIRS,
Side rail - integral roof rack - 5 door.
3.Using a suitable hooked tool in the front foot
hole of the roof finisher, slide the finishers 2
forward clips rearward from the roof channel.
4.Slide the clip rear of the foot hole forward from
the roof channel.
5.Slide the remaining 7 clips from the roof
channel.
6.Remove nut securing rear end of roof finisher
and remove finisher.
7.Remove clips from roof finisher.Refit
1.Fit clips to roof finisher.
2.Fit finisher to roof channel with forward 2 clips.
3.Slide finisher to align with screen. Feed forward
clip below screen seal.
4.Fit remaining clips to roof channel.
5.Fit nut and secure rear end of finisher.
6.Ensure full length of finisher is correctly seated
in roof channel.
7.Fit roof finisher caps or roof rack side rail.

+ EXTERIOR FITTINGS, REPAIRS,
Side rail - integral roof rack - 5 door.
8.Fit tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.

BODY DIMENSIONS
BODY DIMENSIONS 77-1-1
BODY DIMENSIONS BODY DIMENSIONS
Dimensional Information
Measurement Types
The following dimensional information is shown so as to assist the technician in the diagnosis and repair of body
panels. The information is shown in two different ways. There are X,Y,Z dimensions and actual point to point
dimensions.
The X,Y,Z dimensions are the measuring planes used within Land Rover for the measurement of body panels. The
whole bodyshell is within a parallel grid system, see illustrations below.
The X plane is an imaginary vertical plane starting at the front of the vehicle. It is at right angles to the centre line of
the vehicle and measures distances along the length of the vehicle.
The Y plane is an imaginary plane through the centre of the vehicle. All Y dimensions start from this plane. As a rule,
body dimensions are symmetrical about the centre line.
The Z plane is set at a fixed distance parallel to the underside of the vehicle. All Z dimensions start from this plane.
The point to point measurements are actual distances between two points. These points can be holes or intersection
points. Where holes are taken, the point of measurement is always from the hole centre.
Measurements shown are in millimetres and inches. The measurements shown in brackets are in inches.
The tolerance for the basic geometry of the vehicle is ± 1.0 mm (0.040). This includes tooling holes, all fixing holes
and apertures.
The tolerance for matching panel form and break lines is ± 0.5 mm (0.020).

BODY DIMENSIONS
77-1-6 BODY DIMENSIONS
Under body information
Item From To Length
A Front crossmember, jig location hole Front subframe, rear mounting hole 1197.3 (47.137)
B Front crossmember, jig location hole Front subframe, rear mounting hole 985.7 (38.807)
C Front Subframe, front mounting hole `LH` Front subframe, front mounting hole `RH` 772.0 (30.393)
D Front subframe, front mounting hole Front subframe, rear mounting hole 295.3 (11.625)
E Front subframe, front mounting hole Front subframe, rear mounting hole 772.5 (30.413)
F Front subframe, rear mounting hole `RH` Front subframe rear mounting hole `LH` 660.0 (25.984)
G Front subframe, rear mounting hole Rear longitudinal front, jig location hole 1577.3 (62.098)
H Front subframe, rear mounting hole Rear subframe, front mounting hole 2129.9 (83.854)
J Rear longitudinal front, jig location hole Rear subframe, front mounting hole 983.0 (38.700)
K Rear subframe, front mounting hole `LH` Rear subframe front mounting hole `RH` 930.0 (36.614)
L Rear longitudinal front, jig location hole Rear subframe, front mounting hole 403.4 (15.881)
M Rear subframe, front mounting hole Rear crossmember, jig location hole 822.3 (32.374)
N Rear subframe, front mounting hole Rear crossmember, jig location hole 1199.5 (47.224)

BODY DIMENSIONS
BODY DIMENSIONS 77-1-7
Under body information
Item From To Length
A Sidemember, forward jig location hole `LH` Sidemember, forward jig location hole `RH` 962 (37.874
B Sidemember, forward jig location hole Front subframe, rear mounting hole 1216.0 (47.874
C Spring location, inboard fixing hole `LH` Spring location, inboard fixing hole `RH` 1029.8 (40.543)
D Spring location, inboard fixing hole Front subframe, rear mounting hole 396.4 (15.606)
E Spring location, inboard fixing hole Front subframe, rear mounting hole 914.8 (36.015)
F Link arm fix, `LH` Link arm fix, `RH` 926.2 (36.464)
G Rear longitudinal front, jig location hole Rear subframe, front mounting hole 403 (15.866)
H Link arm fix Rear subframe, front mounting hole 1072.2 (42.212)
J Rear subframe, front mounting hole Spring location, rear hole 364.2 (14.338)
K Rear subframe, front mounting hole Spring location, rear fixing hole 1125.7 (44.318)
L Rear subframe, front mounting hole Rear longitudinal rear, jig location hole 1213.0 (47.755
M Spring location, rear fixing hole `LH` Spring location, rear fixing hole `RH` 1220.0 (48.031
N Rear subframe, front mounting hole Rear longitudinal rear, jig location hole 700.7 (27.586)
P Rear longitudinal rear, jig location hole `LH` Rear longitudinal rear, jig location hole `RH` 1054.0 (41.496)

BODY DIMENSIONS
77-1-8 BODY DIMENSIONS
Under body information
Item From To Length
A Link arm fix, `LH` Link arm fix, `RH` 926.2 (36.464)
B Rear crossmember, jig location hole `LH` Rear crossmember, jig location hole `RH` 820 (32.283)
C Rear subframe, front mounting hole `LH` Rear subframe, front mounting hole `RH` 930 (36.614)
D Rear subframe, rear mounting hole `LH` Rear Subframe, rear mounting hole `RH 1030 (40.551)
E Spring location, rear fixing hole `LH` Spring location, rear fixing hole `RH` 1219.9 (48.027)
F Link arm fix Rear subframe, rear mounting hole 906.7 (35.696)
G Rear Subframe, front mounting hole Rear subframe, rear mounting hole 369.7 (14.555)
H Rear subframe, rear mounting hole Rear crossmember, jig location hole 450.8 (17.748)
J Zero `Z` datum Link arm fix 160 (6.299)
K Zero `Z` datum Rear longitudinal rear, jig location hole 272.8(10.740)
L Zero `Z` datum Rear crossmember, jig location hole 299.5 (11.791)
M Zero `Z` datum Rear longitudinal rear, jig location hole 303.5 (11.948)
N Zero `Z` datum Spring location, rear fixing hole 728.5 (28.681)

BODY DIMENSIONS
BODY DIMENSIONS 77-1-9
Under body information
Item From To Length
A Outrigger panel, jig location hole 'LH' Outrigger panel, jig location hole 'RH' 1070 (42.1250)
B Sidemember, forward jig location hole 'LH' Sidemember, forward jig location hole 'RH' 962 (37.874)
C Front crossmember, jig location hole 'LH' Front crossmember, jig location hole 'RH' 700 (27.559)
D Sidemember, jig location hole 'LH' Sidemember jig location hole 'RH' 892 (35.118)
E Front subframe, front mounting hole 'LH' Front subframe, front mounting hole 'RH' 772 (30.393)
F Front subframe, rear outer mounting hole 'LH' Front subframe, rear outer mounting hole 'RH' 859 (33.818)
G Front subframe, rear inner mounting hole 'LH' Front subframe, rear inner mounting hole 'RH' 660 (25.984)
H Front subframe, front mounting hole Front subframe, rear mounting hole 290 (11.417)
J Outrigger panel, jig location hole Front subframe, rear mounting hole 69 (2.716)
K Front subframe, rear mounting hole Tunnel front cross member, jig location hole 748 (29.448)
L Spring location, hole Front subframe, rear mounting hole 350.6 (13.803)
M Sidemember, forward jig location Front subframe, rear mounting hole 906 (35.669)
N Front crossmember, jig location hole Front subframe, rear mounting hole 985.5 (38.799)
P Front subframe, rear mounting hole Tunnel rear cross member, jig location 1051 (41.377)
R Zero 'Z' datum Spring location, inboard fixing hole 693.7 (27.311)
S Zero 'Z' datum Sidemember, jig location hole 388 (15.275)
T Zero 'Z' datum Sidemember, bottom jig location hole 312 (12.283)
U Zero 'Z' datum Front crossmember, jig location hole 154.4 (6.176))
V Zero 'Z' datum Front subframe, front mounting hole 125 (4.921)
W Zero 'Z' datum Front subframe, rear mounting hole 95.8 (3.771))

BODY DIMENSIONS
77-1-10 BODY DIMENSIONS
Front end point to point information
Item From To Length
A Headlamp fixing Wing, forward fixing 150 (5.905)
B Headlamp fixing Wing, rear fixing 1507.7 (59.358)
C Wing, forward fixing `LH` Wing, forward fixing `RH` 1338 (13.307)
D Headlamp fixing Spring location, inboard hole 520.1 (20.476)
E Spring location, inboard hole Headlamp fixing 1239.9 (48.814)
F Spring location, inboard hole Wing, rear fixing 300.8 (11.842)
G Spring location, inboard hole `LH` Spring location, inboard hole `RH` 1029.8 (40.543)
H Wing, rear fixing `LH` Wing, rear fixing `RH` 1380 (54.330)

BODY DIMENSIONS
BODY DIMENSIONS 77-1-11
Front and side information
Item From To Length
A Wing, rear fixing Top corner, on bodyside panel 1532.7 (60.342)
B Top corner, on bodyside panel `LH` Top corner, on bodyside panel `RH` 1045.8 (41.173)
C Top hinge fixing, rear hole Door striker, top fixing 1228.2 (48.354)
D Bottom hinge fixing, rear hole Door striker, top fixing 1268.1 (49.925)

BODY DIMENSIONS
77-1-12 BODY DIMENSIONS
Rear end information
Item From To Length
A Top corner, on bodyside panel `LH` Top corner, on bodyside panel `RH` 980 (38.582)
B Top corner, on bodyside panel Bottom corner, on bodyside panel 1684.5 (66.318)
C Bottom corner, on bodyside panel `LH` Bottom corner, on bodyside panel `RH` 1349 (53.110)

BODY DIMENSIONS
BODY DIMENSIONS 77-1-13
Side information
Item From To Length
A 'A' post, top hinge, rear fixing hole 'B/C' post, top hinge, top fixing hole 1007.7 (39.673)
B 'A' post, top hinge, rear fixing hole 'B/C' post, bottom hinge, front fixing hole 1026.4 (40.409)
C 'A' post, bottom hinge, rear fixing hole 'B/C' post, top hinge, top fixing hole 1088.4 (42.850)
D 'A' post, bottom hinge, rear fixing hole 'B/C' post, bottom hinge, front fixing hole 980.4 (38.598)
E 'B/C' post, top hinge, rear fixing hole 'D' post, door striker, top fixing hole 828.7 (32.625)
F 'B/C' post, bottom hinge, rear fixing hole 'D' post, door striker, top fixing hole 916.5 (36.082)