Lexus CT200h 2011 Owner's Manual (in English)

211
2-1. Driving procedures
2
When driving
CT200h_EE (OM76041E)
CAUTION
When driving on slippery road surfaces
Do not accelerate or shift the shift position suddenly.
Sudden changes in engine braking may cause the vehicle to spin or skid,
resulting in an accident.
For the shift lever
Do not remove the shift lever knob or use anything but a genuine Lexus
shift lever knob. Also, do not hang anything on the shift lever.
Doing so could prevent the shift lever from returning to position, causing
unexpected accidents to occur when the vehicle is in motion.
P position switch
Do not press the P position switch while the vehicle is moving.
If the P position switch is pressed when driving at very low speeds (for
example, directly before stopping the vehicle), the vehicle may stop sud-
denly when the shift position switches to P, which could lead to an accident.

212
2-1. Driving procedures
CT200h_EE (OM76041E)
NOTICE
Hybrid battery (traction battery) charge
If the shift position is in N, the hybrid battery (traction battery) will not be
charged. To help prevent the battery from discharging, avoid leaving the N
position selected for an extended period of time.
Situations where P position control system malfunctions are possible
If any of the following situations occurs, P position control system malfunc-
tions are possible.
Immediately stop the vehicle in a safe place on level ground, apply the park-
ing brake, and then contact any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
When the “P LOCK MALFUNCTION” appears on the multi-information
display. (P. 567)
When the shift position indicator remains off.
Notes regarding shift lever and P position switch operation
Avoid repeatedly operating the shift lever and P position switch in quick
succession.
The system protection function may activate and it will not be temporarily
possible to shift the shift position other than P. If this happens, please wait
for a while before attempting to change the shift position again.

213
2-1. Driving procedures
2
When driving
CT200h_EE (OM76041E)
Turn signal lever
Turn signals can be operated when
The “POWER” switch is in ON mode.
If the indicator flashes faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned
out.
The turn signal lever can be used to show the following intention
of the driver:
Right turn
Left turn
Lane change to the right
(push and hold the lever
partway)
The right hand signals will
flash until you release the
lever.
Lane change to the left
(push and hold the lever
partway)
The left hand signals will
flash until you release the
lever.

214
2-1. Driving procedures
CT200h_EE (OM76041E)
Parking brake
Parking brake engaged warning buzzer
The buzzer sounds to indicate that parking brake is still engaged (with the
vehicle having reached a speed of 5 km/h [3 mph]). (P. 571)
Usage in winter time
See “Winter driving tips” for parking brake usage in winter time. (P. 3 0 4 )
NOTICE
Before driving
Fully release the parking brake.
Driving the vehicle with the parking brake set will lead to brake components
overheating, which may affect braking performance and increase brake
wear.
To set the parking brake,
fully depress the parking
brake pedal with your left
foot while depressing the
brake pedal with your right
foot.
(Depressing the pedal again
releases the parking brake.)

215
2-1. Driving procedures
2
When driving
CT200h_EE (OM76041E)
Horn
After adjusting the steering wheel
Make sure that the steering wheel is securely locked.
The horn may not sound if the steering wheel is not securely locked. (P.
111)
To sound the horn, press on
or close to the mark.

216
CT200h_EE (OM76041E)
2-2. Instrument cluster
Gauges and meters
The following gauges and meters and display illuminate when the
“POWER” switch is in ON mode:
Hybrid System Indicator
Displays hybrid system output or regeneration level
Tachometer (if equipped)
Displays the engine speed in revolutions per minute
Speedometer
Displays the vehicle speed
ECO lamp and SPORT lamp (if equipped)
Changes colors according to driving mode
Fuel gauge
Displays the quantity of fuel remaining in the tank
Multi-information display
P. 226
Outside temperature
The temperature range that can be displayed is from -40 C (-40 F)
to 50 C (122 F)

217
2-2. Instrument cluster
2
When driving
CT200h_EE (OM76041E)
Changing the display
Switches between odometer
and trip meter displays. When
the trip meter is displayed,
pressing and holding the button
will reset the trip meter.
Odometer and trip meter display
Odometer: Displays the total distance that the vehicle has
been driven
Trip meter: Displays the distance the vehicle has been driven
since the meter was last reset. Trip meters “A” and
“B” can be used to record and display different
distances independently.
Odometer/trip meter display change button

218
2-2. Instrument cluster
CT200h_EE (OM76041E)
Instrument panel light control
The brightness of the instrument panel lights can be adjusted by
turning the dial.
Brighter
Darker
When the headlight switch is
turned to ON, the brightness
will be reduced slightly unless
the control dial is turned fully
up.

219
2-2. Instrument cluster
2
When driving
CT200h_EE (OM76041E)
Hybrid System Indicator
Hybrid System Indicator is displayed when the driving mode is other
than the sport mode.
By keeping the indicator needle within Eco area, more Eco-friendly driv-
ing can be achieved.
Charge area indicates regeneration* status. Regenerated energy will be
used to charge the battery.
*:When used in this manual, “regeneration” refers to the conversion of
energy created by the movement of the vehicle into electrical energy.
Power area
Shows that an Eco-friendly driving
range is being exceeded (during full
power driving etc.)
Eco area
Shows that the vehicle is being driven
in an Eco-friendly manner.
Hybrid Eco area
Shows that gasoline engine power is
not being used very often.
The gasoline engine will automatically
stop and restart under various condi-
tions.
Charge area
Shows that energy is being recovered

220
2-2. Instrument cluster
CT200h_EE (OM76041E)
ECO lamp and SPORT lamp
When sport mode is selected, the SPORT lamp (red) will illuminate.
When all of the following conditions are satisfied and the Eco-friendly
driving, the ECO lamp (blue) will illuminate:
• When driving with the shift position in D
• When either normal mode or Eco mode are selected, and EV drive
mode is not in use
• The vehicle speed is 130 km/h (80 mph) or below.
Tachometer
Hybrid System Indicator automatically switches to the tachometer when the
driving mode is set to the sport mode. However, while the cruise control or
dynamic radar cruise control is active, Hybrid System Indicator will not
automatically switch to the tachometer. When the cruise control or dynamic
radar cruise control is activated while the tachometer is displayed, the
tachometer will automatically switch to Hybrid System Indicator.
Engine speed
On hybrid vehicles, engine speed is precisely controlled in order to help
improve fuel efficiency and reduce exhaust emissions etc.
There are times when the engine speed that is displayed may differ even
when vehicle operation and driving conditions are the same.
Outside temperature display
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
When stopped, or driving at low speeds (less than 20 km/h [12 mph])
When the outside temperature has changed suddenly (at the entrance/exit
of a garage, tunnel, etc.)