Lexus ES300 1999 Owner's Manuals (in English)

COMFORT ADJUSTMENT
181
16E114±1
CAUTION
Push and pull the child restraint system in different
directions to be sure it is secure. Follow all the
installation instructions provided by its manufacturer.
16E115b

COMFORT ADJUSTMENT
1824. To remove the convertible seat, press the
buckle±release button and allow the belt to retract
completely. The belt will move freely again and be ready
to work for an adult or older child passenger.
(C) Booster seat installation
16E105±3
A booster seat is used in forward±facing position only.

COMFORT ADJUSTMENT
183
16L152

Move seat fully back

COMFORT ADJUSTMENT
184
CAUTION
A forward±facing child restraint system should be put
on the front seat only when it is unavoidable. Always
move the seat as far back as possible, because the
force of a deploying airbag could cause death or serious
injury to the child. Do not allow the child to lean over the
front door or around the front door even if the child is
seated in a child restraint system. It is dangerous if the
side airbag inflates, and the impact could cause death
or serious injury to the child.
16E116±2

COMFORT ADJUSTMENT
185
1. Sit the child on a booster seat. Run the lap and
shoulder belt through or around the booster seat and
child following the instructions provided by its
manufacturer and insert the tab into the buckle.
Make sure the shoulder belt is correctly across the
child's
shoulder and that the lap belt is positioned as low
as possible on child's hips. See ºSeat beltsº on page 125
for details.
CAUTION
 Always make sure the shoulder belt is positioned
across the center of child's shoulder. The belt should
be kept away from child's neck, but not falling off
child's shoulder. Failure to do so could reduce the
amount of protection in an accident and cause
serious injuries in a collision.
 High±positioned lap belts and loose±fitting
belts both could cause serious injuries due to
sliding under the lap belt during a collision or
other unintended result. Keep the lap belt
positioned as low on hip as possible.
 For child's safety, do not place the shoulder
belt under child's arm.
 After inserting the tab, make sure the tab and
buckle are l ocked and that the lap and shoulder
portions of the belt are not twisted.
 Do not insert coins, clips, etc. in the buckle as
this may prevent you from properly latching the
tab and buckle.
 If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not
use the seat until the seat belt is fixed. It cannot
protect your child from injury.

COMFORT ADJUSTMENT
186
16E117b
2. To remove the child restraint system, press the
buckle±release button and allow the belt to retract.Top strap anchors and locations
16E032
If your child restraint system requires the use of a
top strap, latch the hook onto the anchor bracket
and tighten the top strap.
See the following instructions to install the anchor
bracket.

COMFORT ADJUSTMENT
187
16E033

1Center 2341.6 mm (13.4 in.) 3 92 mm (3.6
in.)
460 mm (2.4 in.)
1. Run your fingers across the trim of the filler panel to
locate the holes underneath it in the positions shown
above.
2. Make a hole in the covering directly above the hole in
the filler panel.

COMFORT ADJUSTMENT
188
16E034±1

1Bolt 2Anchor bracket 3Spacer
3. Insert a 15 mm (0.6 in.) spacer, and tighten down the
anchor bracket for your child restraint system with a bolt.
Torque the bolt to 16.5 ± 24.7 N´m (1.68 ±2.52 kgf´m,
12.2 ± 18.2 ft´lbf.).
To comply with Canadian Motor Vehicle Safety
Standards, this model sold in Canada is provided with a
bracket set in the glovebox, designed for use with any of
the 3 anchor locations shown in the illustration.
DRIVING POSITION MEMORY SYSTEM
The micro computer can memorize the position of the
driver's seat. Two different driving position profiles can
be entered into the computer's memory.
Recording a driving position in the computer's memory
can only be done when the ignition key is in the ºONº
position and the selector lever is in the ºPº position.
Setting a driving position
16E047

COMFORT ADJUSTMENT
189
1. Adjust the driver's seat to the desired position.
2. While
pushing the ºSETº button, push button º1º
or º2º until the signal beeps.
The beep sound means that the positions are recorded
in the computer's memory. By repeating these two steps and pressing the
remaining button, the driving position for another driver
can be recorded.
To set a new memorized position, select the desired
position and perform step 2. The previous memory will
be erased and the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the
memorized position, then make the desired changes
and perform step 2 above.

COMFORT ADJUSTMENT
190
Activating a memorized position
16E048
When you push button º1º or º2º, the driving
position will be automatically adjusted to the
position recorded for that button.