stop start LEXUS ES350 2023 Owners Manual

3
ES350_ES250_QG_OM06255U_(U)
QInstrument panel
Engine switch ...............................................................................................................P.1 7
Starting the engine/changing the mode............................................................... P.17, 18
Emergency stop of the engine ......................................................................................... P.19
When the engine will not start ....................................................................................... P.80
Warning messages
*1
Shift lever .................................................................................................................... P.20
Changing the shift position.............................................................................................. P.20
Precautions against towing
*1
When the shift lever does not move*1
Meters*1
Reading the meters/adjusting the instrument panel lights*1
Warning lights/indicator lights .......................................................................................P.75
When the warning lights come on
*1
Multi-information display ...................................................................................... P.27
Display....................................................................................................................................... P.27
When the warning messages are displayed
*1
Pictorial Index
A
B
C
D

26
ES350_ES250_QG_OM06255U_(U)
Turns the brake hold system on
The brake hold standby indicator (green) comes on. While the system is holding
the brake, the brake hold operated indica-
tor (yellow) comes on.
Brake Hold
The brake hold system keeps the brake applied wh en the shift lever is in D, S or N with the
system on and the brake pedal has been de pressed to stop the vehicle. The system
releases the brake when the accelerator pedal is depressed with the shift lever in D or S to
allow smooth start off.
A
B

59
ES350_ES250_QG_OM06255U_(U)
The following tables list frequently used commands for each function category.
OThe functions available may vary according to the system installed.
O Items with subscription will require Intelligent Assistant functionality.
QCommon
QNavigation
Intelligent Assistant system enables navigation voice search. This allows you with variety of
features such as searching a point of interest (P OI), navigate to an address as well as discov-
ering new POIs.
Function list
ActionExample voice commandSubscription
Shows list of general commands“Help”No
Stops the current con-versation and re-starts
at the beginning“Start over”No
Cancels the voice con- trol system“Cancel”No
FunctionExample voice commandSubscription
Destination search
“Take me to <location category/business name>”
“Take me to <an Italian restaurant>”“Take me to <address>”
“Take me to <6565 Headquarters drive Plano
TX>”
“Take me home”
“Take me to work”
Yes
Map control“Map zoom in”
“Map zoom out”Yes
Route information“Cancel trip”Yes
Telematics“Call destination assist”No

67
ES350_ES250_QG_OM06255U_(U)
QEnabling 2-way communication with a garage door (only available for compat-
ible devices)
When enabled, 2-way communication allows you to check the status of the opening and
closing of a garage door through indicators in your vehicle.
2-way communication is only available if the garage door opener motor used is a compati-
ble device. (To check device compatibility, refer to www.homelink.com.)
1Within 5 seconds after programming the garage door opener has been completed, if
the garage door opener motor is trained to HomeLink
®, both garage door operation
indicators will flash rapidly (green) and the light on the garage door opener motor will
blink twice, indicating that 2- way communication is enabled.
If the indicators do not flash, perform
2 and 3 within the first 10 presses of the HomeLink®
button after programming has been completed.
2Press a programmed HomeLink® button to operate a garage door.
3Within 1 minute of pressing the HomeLink® button, after the garage door operation
has stopped, press the “Learn” or “Smart” button on the garage door opener motor.
Within 5 seconds of the establishment of 2-way communication with the garage door
opener, both garage door operation indicators in the vehicle will flash rapidly (green)
and the light on the garage d oor opener motor will blink tw ice, indicating that 2-way
communication is enabled.
QReprogramming a single HomeLink® button
When the following procedure is performed, buttons which already have devices registered
to them can be overwritten:
1With one hand, press and hold the desired HomeLink® button.
2When the HomeLink® indicator starts flashing (orange), continue to hold the
HomeLink
® button and perform “Programming HomeLink®” 1 (it takes 20 seconds
for the HomeLink
® indicator to start flashing).
Press the appropriate HomeLink
® button. The HomeLink® indicator light should turn on.
Operating HomeLink®