Lexus GS350 2014 Navigation manual

61
2. NETWORK SETTINGS
BASIC FUNCTION
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
2
1Select the device to be connected.
zSupported profile icons will be displayed.
: Telephone
: Audio player
zSupported profile icons for currently con-
nected devices will illuminate.
z Dimmed icons can be selected to connect
to the function directly.
2Select the desired connection.
X When another Bluetooth
® device is con-
nected
z To disconnect the Bluetooth® device,
select “Yes”.
3Check that a confirmation screen is dis-
played when the connection is complete.
z If an error message is displayed, follow the
guidance on the screen to try again.
CONNECTING A Bluetooth®
DEVICE
Up to 5 Bluetooth
® devices (Tele-
phones (HFP) and audio players (AVP))
can be registered.
If more than 1 Bluetooth
® device has
been registered, select which device to
connect to.
z If the desired Bluetooth® device is not on
the list, select “A d d ” to register the
device. ( →P. 5 9 )
INFORMATION
●
It may take time if the device connection
is carried out during Bluetooth® audio
playback.
●Depending on the type of Bluetooth®
device being connected, it may be neces-
sary to perform additional steps on the
device.
GS_Navi+MM_OM30E40E_(EE).book Page 61 Thursday, July 24, 2014 3:57 PM

62
2. NETWORK SETTINGS
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
■AUTO CONNECTION MODE
zWhen the engine <power> switch is in
ACCESSORY or IGNITION ON <ON>
mode, the system searches for a nearby
registered device.
z The system will connect with the registered
device that was last connected, if it is
nearby.
■ CONNECTING MANUALLY
1Press the “MENU” button on the
Remote Touch and select “Setup”.
2Select “Bluetooth*” .
3Follow the steps in “CONNECTING A
Bluetooth
® DEVICE” from “STEP 1”.
( → P.61)
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
■ RECONNECTING THE Bluetooth®
PHONE
zIf a Bluetooth® phone is disconnected on
purpose, such as turning it off, this does not
happen. Reconnect the Bluetooth
® phone
manually.
To turn auto connection mode on, set
“Bluetooth* power” to on. ( →P.66)
Leave the Bluetooth
® device in a loca-
tion where the connection can be estab-
lished.
When the auto connection has failed or
“Bluetooth* power” is turned off, it is
necessary to connect Bluetooth
® man-
ually.
If a Bluetooth® phone is disconnected
due to poor reception from the
Bluetooth
® network when the engine
<power> switch is in ACCESSORY or
IGNITION ON <ON> mode, the sys-
tem automatically reconnects the
Bluetooth
® phone.
GS_Navi+MM_OM30E40E_(EE).book Page 62 Thursday, July 24, 2014 3:57 PM

63
2. NETWORK SETTINGS
BASIC FUNCTION
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
2
1Select the desired device to be edited.
2Select “Device info” .
3Confirm and change the Bluetooth®
device information.
EDITING THE Bluetooth®
DEVICE INFORMATION
The Bluetooth
® device’s information
can be displayed on the screen. The dis-
played information can be edited.
No.Information
The name of the Bluetooth® device
can be changed to a desired name.
( → P.64)
Device address is unique to the de-
vice and cannot be changed.
The telephone number of the
Bluetooth® phone.
Compatibility profile of the
Bluetooth® device.
Select to set the Bluetooth® audio
player connection method. ( →P.64)
Select to reset all setup items.
GS_Navi+MM_OM30E40E_(EE).book Page 63 Thursday, July 24, 2014 3:57 PM

64
2. NETWORK SETTINGS
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
■CHANGING A DEVICE NAME
1Select “Device name” .
2Enter the name and select “OK”.
■SETTING AUDIO PLAYER CON-
NECTION METHOD
1Select “Connect audio player from” .
2Select the desired connection method.
“Vehicle” : Select to connect the audio sys-
tem to the audio player.
“Device” : Select to connect the audio play-
er to the audio system.
z Depending on the audio player, the “Vehi-
cle” or “Device” connection method may
be best. As such, refer to the manual that
comes with the audio player.
z To reset the connection method, select
“Defaults” .
INFORMATION
●
If 2 Bluetooth® devices have been regis-
tered with the same device name, the
devices can be distinguished referring to
the device’s address.
●Depending on the type of telephone,
some information may not be displayed.
INFORMATION
●
Even if the device name is changed, the
name registered in your Bluetooth®
device does not change.
GS_Navi+MM_OM30E40E_(EE).book Page 64 Thursday, July 24, 2014 3:57 PM

65
2. NETWORK SETTINGS
BASIC FUNCTION
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
2
1Display the “Bluetooth*” screen.
(→ P.57)
2Select “Detailed Bluetooth* settings” .
3Select the desired item to be set.
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
“Detailed Bluetooth* settings”
SCREEN
The Bluetooth® settings can be con-
firmed and changed.
No.InformationPage
Select to set Bluetooth®
connection on/off. 66
Displayed system name can
be changed to a desired
name.66
PIN code used when the
Bluetooth® device was reg-
istered. It can be changed to
a desired code.66
Device address is unique to
the device and cannot be
changed.
Select to set the telephone
connection status display
on/off.
Select to set the connection
status display of the audio
player on/off.
Compatibility profile of the
system. 
Select to reset all setup
items.
GS_Navi+MM_OM30E40E_(EE).book Page 65 Thursday, July 24, 2014 3:57 PM

66
2. NETWORK SETTINGS
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
1Select “Bluetooth* power” .
When “Bluetooth* power” is on :
The Bluetooth
® device is automatically
connected when the engine <power> switch
is in ACCESSORY or IGNITION ON
<ON> mode.
When “Bluetooth* power” is off :
The Bluetooth
® device is disconnected,
and the system will not connect to it next
time.
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
1Select “System name” .
2Enter a name and select “OK”.
1Select “PIN code” .
2Enter a PIN code and select “OK”.
CHANGING “Bluetooth*
power”
INFORMATION
●
While driving, the auto connection state
can be changed from off to on, but can-
not be changed from on to off.
EDITING THE SYSTEM NAME
EDITING THE PIN CODE
GS_Navi+MM_OM30E40E_(EE).book Page 66 Thursday, July 24, 2014 3:57 PM

67
2. NETWORK SETTINGS
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
BASIC FUNCTION
2
3. CONNECTING TO INTERNET VIA Bluetooth® DEVICE
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Bluetooth*” .
4Select “Communication settings” .
5Select “Yes”.
zA portal account is an account that is
obtained from the website Lexus prepares
for its customers.
6Select “Country” .
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
SETTING INTERNET
CONNECTION
To use the internet via Bluetooth® de-
vice, it is necessary to register a
Bluetooth
® device with the system.
Once the device has been registered, it
is possible to use the internet via
Bluetooth
® device.
For details about registering a
Bluetooth
® device: →P.59
GS_Navi+MM_OM30E40E_(EE).book Page 67 Thursday, July 24, 2014 3:57 PM

68
2. NETWORK SETTINGS
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
7Select a country.
zThe previous screen will be displayed.
8Select “Provider” on the “Communica-
tion settings” screen.
9Select your mobile network provider.
10Select “OK” on the “Communication
settings” screen.
z If “Other ” is selected for country and/or
mobile network provider, the “Detail set-
tings” screen will be displayed. ( →P. 6 9 )
z The system will automatically set the details
of the mobile network provider’s informa-
tion and perform a communication con-
nection test.
z If the setting cannot be performed auto-
matically, the “Detail settings” screen will be
displayed. ( →P. 6 9 )
11When the cellular phone has been con-
nected successfully, “Data connection
successful.” will be displayed on the
screen. The online search and importing
memory points function will be avail-
able.
zBefore performing a communication
connection test, a confirmation screen
will be displayed in accordance with the
connected service settings. ( →P. 4 1 3 )
z When accessing Lexus portal site using a
cellular phone, your user name and pass-
word will be required. ( →P. 6 9 )
GS_Navi+MM_OM30E40E_(EE).book Page 68 Thursday, July 24, 2014 3:57 PM

69
2. NETWORK SETTINGS
BASIC FUNCTION
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
2
■“Detail settings” SCREEN
zEnter or select “Username” (for APN set-
ting), “Password” (for APN setting), “APN”,
“DNS 1”, “DNS 2”, “Dial number” and
“Script”.
z If there is only one DNS, set it in DNS 1.
z If more than one item needs to be entered
into “Script”, separate the first and second
items with a semi-colon (;).
If the navigation system does not have
mobile network provider setting infor-
mation for the country or mobile net-
work provider that has been selected, or
if you select “Other ” for either country
or mobile network provider, the “Detail
settings” screen will be displayed. Con-
tact your mobile network provider to
obtain the contract information to be in-
put in the “Detail settings” screen.
GS_Navi+MM_OM30E40E_(EE).book Page 69 Thursday, July 24, 2014 3:57 PM

70
2. NETWORK SETTINGS
GS_Navi+MM_OM30E40E_(EE)
14.07.24 15:56
4. CONNECTING TO INTERNET VIA Wi-Fi®*1
1Press the “MENU” button on the
Remote Touch.
2Select “Setup” .
3Select “Wi-Fi*2”.
4Select the items to be set.
*
2: Wi-Fi is a registered mark of the Wi-Fi Alliance®.
Using the Wi-Fi® function, this system
can connect to the internet, which allows
the use of the connected services, traffic
information, etc.
*1: This function is not available in some countries/areas.
GS_Navi+MM_OM30E40E_(EE).book Page 70 Thursday, July 24, 2014 3:57 PM