clock LEXUS GS400 2000 Service User Guide

Ye s
Ye sNo
No
Is there battery positive voltage between terminal +B and
body ground?
Is there battery positive voltage between terminal ACC and
body ground?
Replace clock.+B wire harness faulty.
Ye sNo
Is there continuity between terminal GND and
body ground?Ground wire harnss faulty. ACC wire harness faulty.
2 CLOCK LOSES OR GAINS TIME
I04264
Wire Harness Side5
4
3
6
1RAD NO.2 Fuse
DOME Fuse
Combination
Meter
Body ECU
No.2
Ground ACC
+B
PBEW
ILL
E Clock Assembly
Ye s
Is there battery positive voltage between terminal +B and
body ground?
Adjust or replace clock.Bellow 10 V
Locate cause and repair, or recharge battery.
Ye s
Is there battery positive voltage between terminal ACC and
body ground?Bellow 10 V
Locate cause and repair, or recharge battery.
BE±228
± BODY ELECTRICALCLOCK
2529 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING NO.2
(a) Check that the battery positive voltage is 10 ± 16 V.
If voltage is not as specified, replace the battery.
(b) Inspect the error of the clock.
Allowable error (per day): ± 1.5 seconds
If the error exceeds the allowable error, replace the clock.
(c) Check that the clock adjusting button is sticking in posi-
tion and has failed to return.
If the error exceeds the allowable error, replace the clock.
(d) Troubleshoot the clock as follows.
HINT:
Inspect the connector on the wire harness side.

BE0G1±08
I01374
Ignitioin SwitchClock Assembly
Driver Side Junction Block

SRS ACC Fuse
Passenger Side
Junction Block

DOME Fuse
± BODY ELECTRICALCLOCK
BE±229
2530 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
LOCATION

± BODY ELECTRICALTROUBLESHOOTING
BE±9
2310 Author: Date:
2000 LEXUS GS300/GS400 (RM718U) Washer fluid does not operate.
Washer Hose and Nozzle±

When wiper switch is in HI position, the wiper blade is in contact
with the body.

When the wiper switch is OFF, the wiper blade does not retract
or the retract position is wrong.
1. Wiper Motor *1
2. Wire harness *1BE±77
±
*1: Inspect wiper arm and blade set positions.
COMBINATION METER
This system uses the multiplex communication system, so check diagnosis system of the multiplex
communication system before you proceed with troubleshooting.
Refer to DI section for warning light or indicator light not described in the table below.
SymptomSuspect AreaSee page
Driver seat belt warning light does not light up.
1. Bulb
2. Driver Buckle Switch CIrcuit
3. Meter Circuit Plate
4. Wire Harness
5. Body No.2 ECU±
BE±92
BE±92
±
DI±820
Passenger seat belt warning light does not light up.
1. Clock System
2. Passenger Buckle Switch CIrcuit
3. Occupant Detection Sensor
4. Meter Circuit Plate
5. Wire Harness
6. Body No.1 ECUBE±227
BE±92
BE±92
BE±92
±
DI±776
SRS warning light does not light up.
1. MPX±B Fuse
2. SRS±B Fuse
3. Bulb
4. Meter Circuit Plate
5. Wire Harness
6. Airbag Sensor AssemblyBE±21
BE±21
±
BE±92
±
DI±550
Hi±beam indicator light does not light up.
1. Bulb
2. Meter Circuit Plate
3. Wire Harness
4. Headlight System±
BE±92
±
BE±3
Turn indicator light does not light up.
1. Bulb
2. Meter Circuit Plate
3. Wire Harness
4. Turn Signal and Hazard Warning System±
BE±92
±
BE±3
ABS warning light does not light up.
1. GAUGE Fuse
2. Bulb
3. Meter Circuit Plate
4. Wire Harness
5. ABS, TRAC and VSC ECUBE±21
±
BE±92
±
DI±387
TRAC warning light does not light up.
1. GAUGE Fuse
2. Bulb
3. Meter Circuit Plate
4. Wire Harness
5. ABS, TRAC and VSC ECUBE±21
±
BE±92
±
DI±473

BE±14
± BODY ELECTRICALTROUBLESHOOTING
2315 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
w/o Driving Position Memory System:
SymptomSuspect AreaSee page
Mirror does not operate.
1. Mirror Switch
2. Wire Harness
3. Body No.2 ECU
4. Driver and Passenger Door ECUBE±176
±
DI±820
DI±856
DI±889
Mirror operates abnormally.
1. Mirror Switch
2. Mirror Motor
3. Wire Harness
4. Body No.2 ECU
5. Driver and Passenger Door ECUBE±176
BE±176
±
DI±820
DI±856
DI±889
ELECTRO CHROMIC MIRROR SYSTEM
SymptomSuspect AreaSee page
Electro Chromic Inner Mirror does not operate.
1. ECU±IG Fuse
2. Electro Chromic Inner Mirror
3. Wire HarnessBE±21
BE±182
±
Electro Chromic Outer Mirror does not operate.
1. ECU±IG Fuse
2. Electro Chromic Outer Mirror
3. Electro Chromic Inner Mirror
4. Wire HarnessBE±21
BE±182
BE±182
±
SEAT HEATER SYSTEM
SymptomSuspect AreaSee page
Seat heaters do not operate.
(Driver's and Passenger's)
1. SEAT HTR Fuse
2. Seat Heater Switch (D, P)
3. Wire Harness
4. Seat HeaterBE±21
BE±185
±
BE±185
Driver's seat heater does not operate.1. Seat Heater Switch (D, P)
2. Wire HarnessBE±185
±
Passenger's seat heater does not operate.1. Seat Heater Switch (D, P)
2. Wire HarnessBE±185
±
Seat heater temperature is too hot.Seat HeaterBE±185
FUEL LID OPENER SYSTEM
SymptomSuspect AreaSee page
Fuel lid opener system does not operate.
1. FUEL OPN Fuse
2. Fuel Lid Opener Switch
3. Fuel Lid Opener Motor
4. Wire HarnessBE±21
BE±188
BE±188
±
AUDIO SYSTEM
SymptomSuspect AreaSee page
Audio system abnormal operation.TROUBLESHOOTINGSBE±196
CLOCK SYSTEM
SymptomSuspect AreaSee page
Passenger seat belt warning system does not light up.TROUBLESHOOTING NO.1BE±227
Clock will not operate.TROUBLESHOOTING NO.1BE±227
Clock loses or gains time.TROUBLESHOOTING NO.2BE±227

BE0HH±07
I01359
Brake Master Cylinder

Brake Fluid Level
Warning Switch
Combination Meter
and Telltale Light
Assembly
Airbag Sensor Assembly Parking Brake Switch
Driver Side
Junction Block

GAUGE Fuse

SRS±B FuseIgnition Switch
ECM
Washer Tank

Washer Level
Warning Switch Engine Room No.1
Junction Block

MPX±B Fuse
Seat Belt Buckle Switch
Rheostat Light Control
ABS, TRAC and VSC ECU
Clock Assembly

Passenger Seat Belt
Waning Light
BE±80
± BODY ELECTRICALCOMBINATION METER
2381 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
COMBINATION METER
LOCATION
The vehicle shown in this illustration is ºGS400º.
All components of ºGS300º other than the ones used for engine are same as ºGS400º.

I04250

Combination Meter Wiring Circuit ± 1
:Speedometer
:Tachometer
:Fuel Receiver Gauge
:Engine Coolant
Temperature
Receiver Gauge
Speed Control Unit
CLOCK
to GAUGE Fuse
to MPX±B Fuse
to SRS Fuse
Tilt and Telescopic ECU
Body ECU NO.2ECM (GS400)
Ignitor (GS300)
Fuel Main Sender GaugeGround
Fuel Sub Sender Gauge
Light Control Rheostat
Illuminations
ABS, TRAC and VSC ECU
ABS, TRAC and VSC ECU Speed Signal Passenger seat
belt warning
Rr LIGHTS
SEAT BELT
OIL PRESS
OIL LEVEL
DOOR IG+
SRS +BA/T P
A/T R
A/T N
A/T D
A/T 4
A/T 3
A/T 2
A/T L
CRUISE MPX+BIG+IG+
5V
+B
to ECUto
PANEL
Fuse B4
B5
B6
B9
A5
A17A3A8 B16
LCDECU S
T
F
E
Power Source
Brake
Buzzer A11A2 A1 A6
B1
B13
B14A4
B22 ECU
ECU
ECU
S
T
F
E
CHARGE
FUEL LVL
ECT PWR
ECT SNOW TAIL or HEAD
Ground IG+IG+ IG+ IG+
+B
± BODY ELECTRICALCOMBINATION METER
BE±83
2384 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

Clock (Passenger seat belt warning light)
Tilt and telescopic ECU
Fuel main sender gauge
Fuel sub sender gauge
ABS, TRAC and VSC ECU (Speed signal)
Speed control unit
Headlight dimmer switch
Ground
Window washer level warning switch
Body control No.2 ECU
ECM
ABS, TRAC and VSC ECU (VSC warning light)
ABS, TRAC and VSC ECU (SLIP warning light)
ABS, TRAC and VSC ECU (TRAC OFF warning light)
ABS, TRAC and VSC ECU (ABS warning light)
ABS, TRAC and VSC ECU (Brake warning light)
GAUGE fuse
Turn signal flasher (Left turn side)
Turn signal flasher (Right turn side)
Light control rheostat (+B)
Light control rheostat (Signal)
Light control rheostat (Ground)
PANEL fuse
Airbag sensor assembly
MPX+B fuse
DOME+B fuse
HEAD±RH fuse
Igniter
Headlight beam leveling control ECU
Ground
Telltale light assembly (IG+)
Telltale light assembly (ODO/TRIP switch)
Telltale light assembly (Right turn signal)
Telltale light assembly (RESET switch)
Telltale light assembly (Left turn signal)
GroundWiring connector side No.1
1
1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
1 1
1
2
3
4
5
6
9
12
13
14
15
16
18
22
1 1
1
3
4
8
9
10 U B A
± BODY ELECTRICALCOMBINATION METER
BE±85
2386 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

I04105
Dark
(10k W)Bright
(0W)
4
5
I01322
Battery Ignition
SwitchWarning Light
2 1 Wire Harness Side
I01323
1 2 OFF
ON
I01328
Battery Ignition
SwitchWarning Light
2 1 Wire Harness Side
I04107
12
4
OFF
ON BE±102
± BODY ELECTRICALCOMBINATION METER
2403 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
30. INSPECT LIGHT CONTROL RHEOSTAT OPERATION
Gradually, turn the rheostat knob from the bright side to dark
side and check that the resistance decreases from 10 kW to 0
W between terminal 4 and 5. (Rheostat knob turned to clock-
wise)
If operation is not as specified, replace the rheostat light control.
31. INSPECT WINDOW WASHER LEVEL WARNING
LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Engine running and check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
32. INSPECT WINDOW WASHER LEVEL WARNING
SWITCH CONTINUITY
(a) Check that no continuity exists between the terminals with
the switch OFF (float up).
(b) Check that continuity exists between the terminals with
the switch ON (float down).
If operation is not as specified, replace the switch or inspect
ground point.
33. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the retractor switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, inspect the bulb or wire har-
ness.
34. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
(a) Check that continuity exists between the terminals 1 and
4 on the switch side connector with the switch ON (belt
fastened).
(b) Check that continuity exists between the terminals 2 and
4 on the switch side connector with the switch OFF (belt
unfastened).
If operation is not as specified, replace the switch.

Z05962
B02027
Turn
B02028
Move
B01995
Type A
A
Type BB
AB
Z05963
CORRECT WRONG WRONG CH±2
± CHARGING (2JZ±GE)CHARGING SYSTEM
1604 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. INSPECT DRIVE BELT
HINT:
A belt tensioner is used, so checking the belt tension is not nec-
essary.
(a) Visually check the drive belt for excessive wear, frayed
cords, etc.
If necessary, replace the drive belt.
HINT:

Cracks on the rib side of a drive belt are considered ac-
ceptable. If the drive belt has chunks missing from the
ribs, it should be replaced.

The drive belt tension can be released by turning the belt
tensioner clockwise.
(b) Check the belt tensioner operation.

Check that the belt tensioner moves downward
when the drive belt is pressed down at the points in-
dicated in the illustration with approx. 98 N (10 kgf,
22.0 lbf) of force.

Check the alignment of the belt tensioner pulley to
make sure the drive belt will not slip off the pulley.
If necessary, replace the belt tensioner.

Check that the arrow mark on the belt tensioner falls
within area A of the scale.
If it is outside area A, replace the drive belt.
HINT:

When a new belt is installed, it should lie within area B. If
not, the drive belt is not correct.

After installing a drive belt, check that it fits properly in the
ribbed grooves.

Check by hand to confirm that the belt has not slipped out
of the groove on the bottom of the pulley.
6. VISUALLY CHECK GENERATOR WIRING AND
LISTEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) Check that there is no abnormal noise from the generator
while the engine is running.

CH049±01
P10639
Pulley
P10637
B02022
29 mm
Socket
Wrench
B01648
Wire
Clip
P10835
Turn
SST (B)SST (A)
± CHARGING (2JZ±GE)GENERATOR
CH±13
1615 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REASSEMBLY
1. PLACE DRIVE END FRAME ON PULLEY
2. INSTALL ROTOR TO DRIVE END FRAME
3. INSTALL RECTIFIER END FRAME
(a) Place the generator washer on the rotor.
(b) Using a 29 mm socket wrench and press, slowly press in
the rectifier end frame.
(c) Install the 3 nuts.
Torque: 4.5 N´m (46 kgf´cm, 40 in.´lbf)
(d) Install the wire clip with the nut.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. INSTALL PULLEY
(a) Install the pulley to the rotor shaft by tightening the pulley
nut by hand.
(b) Hold SST (A) with a torque wrench, and tighten SST (B)
clockwise to the specified torque.
SST 09820±63010
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(c) Check that SST (A) is secured to the pulley shaft.