navigation Lexus IS250 2015 Navigation Manual

109
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
31Display the “Destination” screen.
(→ P. 107)
2Select “Go Home” .
zThe navigation system performs a search
for the route and the entire route map is
displayed. ( →P. 121)
1Display the “Destination” screen.
(→ P. 107)
2Select any of the preset destination but-
tons (1-5 ).
zThe navigation system performs a search
for the route and the entire route map is
displayed. ( →P. 1 2 1 )
SETTING HOME AS
DESTINATION
To use this function, it is necessary to
register a home address. ( →P. 140)
SETTING PRESET
DESTINATIONS AS
DESTINATION
To use this function, it is necessary to
register preset destinations to the preset
screen buttons (1-5). ( →P. 142)

111
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
3
1Select “Street Address” .
2Enter a house number and select “OK”.
3Enter a street name and select “OK”.
4Select the desired street name.
5Enter a city name and select “OK”.
6Select the desired city name.
zIf the same address exists, the address list
screen will be displayed. Select the desired
address.
1Display the “Destination” screen.
(→ P. 107)
2Select “Point of Interest” .
3Select the desired search method.
SEARCHING BY STREET
ADDRESS
INFORMATION
●A street name can be searched using
only the body part of its name.
Fo r example: S WESTERN AVE
• A search can be performed by entering “S WESTERN AVE”, “WESTERN AVE”
or “WESTERN”.
SEARCHING BY POINT OF
INTEREST
There are 4 methods to search for a des-
tination by Points of Interest.
No.FunctionPage
Select to search by name.112
Select to search by catego-
ry.114
Select to search by phone
number.115
Select to search by eDesti-
nation.377

113
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
3
■SEARCHING FOR POI USING
WEB SEARCH
1Select “ T” next to “Web Search” to se-
lect a search engine.
2Select the desired search engine icon.
z The selected search engine icon will be dis-
played on the top center of the POI list
screen.
3Select the search engine icon.
zAccessing to a search engine
For the procedure on how to conduct a
search via a search engine, go to “SET-
TING A DESTINATION USING
LEXUS App Suite” ( →P. 370), and fol-
low the steps from 3 onward.

115
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
3
XWhen “Near a City Center in XX*” is se-
lected
1Select “Near a City Center in XX” .
2Enter a city name and select “OK”.
“Last 5 Cities” : Select the city name from
the list of the last 5 cities.
3Select the desired city name.
4Select “OK” when the city center map
screen is displayed.
5Follow the steps from 3 onward in
“SEARCHING BY CATEGORY”.
( → P. 114)
*: XX represents the selected search area
name.
1Select “Phone #” .
2Enter a phone number and select “OK”.
zIf there is more than 1 site with the same
number, the list screen will be displayed.
INFORMATION
● If the navigation system has never been
used, selecting the city name from “Last 5
Cities” will not be available.
SEARCHING BY PHONE
NUMBER
INFORMATION
●If there is no match for the entered phone
number, a list of identical numbers with
different area codes will be displayed.

117
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
31Display the “Destination” screen.
(→ P. 107)
2Select “A d d r e s s B o o k ” .
3Select the desired address book entry.
“Options” : Select to register or edit address
book entries. ( →P. 145)
1Display the “Destination” screen.
(→ P. 107)
2Select “Emergency”.
3Select the desired emergency category.
4Select the desired destination.
SEARCHING BY ADDRESS
BOOK
To use this function, it is necessary to
register an address book entry.
(→ P. 144)
SEARCHING BY
EMERGENCY
INFORMATION
●The navigation system does not guide in
areas where route guidance is unavail-
able. ( →P. 1 6 1 )

119
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
3
1Select “Freeway Entrance / Exit” .
2Enter a freeway name and select “OK”.
3Select the desired freeway.
4Select “Entrance” or “Exit”.
5Enter a freeway entrance or exit name
and select “OK”.
6Select the desired entrance or exit
name.
1Display the “Destination” screen.
(→ P. 107)
2Select “Map”.
3Scroll the map to the desired point and
select “Go to ” .
“A d j u s t L o c a t i o n ” : Select to adjust the posi-
tion in smaller increments. ( →P. 92)
zIf a destination has already been set, “Go to
” and “Add to Route” will be displayed.
“Go to ”: Select to delete the existing des-
tination(s) and set a new one.
“Add to Route” : Select to add a destination.
zThe navigation system performs a search
for the route and the entire route map is
displayed. ( →P. 1 2 1 )
SEARCHING BY FREEWAY
ENTRANCE/EXIT
INFORMATION
●Be sure to use the complete name of the
freeway or highway, including the hyphen,
when entering the destination. Freeways
and interstates use an “I” (I-405). US
highways use the state designation before
the number (CA-118).
SEARCHING BY MAP
By selecting “Map” the last displayed lo-
cation is displayed again on the map
screen. You can search for a destination
from this map.

121
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
3
3. STARTING ROUTE GUIDANCE
1Select “OK” to start guidance.
When the destination is set, the entire
route map from the current position to
the destination is displayed.
STARTING ROUTE
GUIDANCE
No.Information/Function
Select the desired route from 3 pos-
sible routes. ( →P. 122)
Select to change the route.
(→ P. 123)
Select to display a list of the turns re-
quired to reach the destination.
(→ P. 123)
Current position
Destination point
Type of route and its distance
Distance of the entire route
Select to start guidance.
If “OK” is selected and held until a
beep sounds, demo mode will start.
Press the “HOME” or “MENU”
button on the Remote Touch to end
demo mode.
CAUTION
● Be sure to obey traffic regulations and
keep road conditions in mind while driv-
ing. If a traffic sign on the road has been
changed, the route guidance may not
indicate such changed information.
INFORMATION
● The route for returning may not be the
same as that for going.
● The route guidance to the destination
may not be the shortest route or a route
without traffic congestion.
● Route guidance may not be available if
there is no road data for the specified
location.
● When setting the destination on a map
with a scale more than 0.5 mile (800 m),
the map scale changes to 0.5 mile (800
m) automatically. If this occurs, set the
destination again.
● If a destination that is not located on a
road is set, the vehicle will be guided to
the point on a road nearest to the destina-
tion. The road nearest to the selected
point is set as the destination.

123
2. DESTINATION SEARCH
IS250/350_Navi_U
NAVIGATION SYSTEM
31Select “Turn List” .
2Check that the turn list is displayed.
1Select “Edit Route”.
2Select the desired item.
DISPLAYING TURN LIST
A list of turn information from the cur-
rent position to the destination can be
displayed.
No.Information
Current position
Distance to the next turn
Turn direction at the intersection
Select to display the map of the se-
lected point.
INFORMATION
● However, not all road names on the route
may appear on the list. If a road changes
its name without requiring a turn (such as
on a street that runs through 2 or more
cities), the name change will not appear
on the list. The street names will be dis-
played in order from the starting point,
along with the distance to the next turn.
EDITING ROUTE
Destinations can be added, reordered
or deleted, and conditions for the route
to the destination can be changed.
No.FunctionPage
Select to add destinations.134
Select to delete destina-
tions. 135
Select to reorder destina-
tions. 135
Select to set route prefer-
ences. 136
Select to change route
type.136

125
IS250/350_Navi_U
NAVIGATION SYSTEM
3
3. ROUTE GUIDANCE
1. ROUTE GUIDANCE SCREEN
During the route guidance, various
types of guidance screens can be dis-
played depending on conditions.
SCREEN FOR ROUTE
GUIDANCE
No.Information
Distance to the next turn and an ar-
row indicating the turning direction
Guidance route
Current position
Current street name or route infor-
mation
INFORMATION
●If the vehicle goes off the guidance route,
the route is searched again.
● For some areas, the roads have not been
completely digitized in our database. For
this reason, the route guidance may
select a road that should not be traveled
on.
● When arriving at the set destination the
destination name will be displayed on the
upper part of the screen.

127
3. ROUTE GUIDANCE
IS250/350_Navi_U
NAVIGATION SYSTEM
3
1Select the route information bar.
2Check that the list of the distance and
time is displayed.
zBy selecting one of the number buttons, the
desired route information is displayed.
1Select “Options” on the map screen.
2Select “Route Overview” .
3Check that the entire route map is dis-
played.
zFor details about this screen: →P. 1 2 1
DISTANCE AND TIME TO
DESTINATION
When driving on the guidance route
with more than 1 destination set, a list of
the distance with estimated travel/arriv-
al time from the current position to each
destination is displayed.ROUTE OVERVIEW
The entire route from the current posi-
tion to the destination can be displayed
during the route guidance.