display Lexus IS300h 2014 Navigation manual

183
5. SETUP
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
1Display the “Parking info settings”
screen. (→P.175)
2Select “Live update (Internet) (Roam-
ing with Bluetooth*)”.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
3Select the desired item.ENABLING PARKING LOT
INFORMATION ROAMING
The roaming function of parking lot in-
formation received via a Bluetooth
® de-
vice can be enabled for roaming
situations (when outside the geographi-
cal coverage area of your mobile net-
work provider). This information can be
set to update automatically or manually.
No.Function
Select to update automatically.
Select to update manually.
(→P.180)
Select to cancel parking lot informa-
tion reception via a Bluetooth® de-
vice.
IS_Navi_EE_53C71E.book 183 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

185
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
zAccurate current position may not be
shown in the following cases:
• When driving on a small angled Y-shaped
road.
• When driving on a winding road.
• When driving on a slippery road such as
in sand, gravel, snow, etc.
• When driving on a long straight road.
• When motorway and surface streets run
in parallel.
• After moving by ferry or vehicle carrier.
• When a long route is searched during
high speed driving.
• When driving without setting the current
position calibration correctly.
• After repeating a change of direction by
going forward and backward, or turning
on a turntable in a parking lot.
• When leaving a covered parking lot or
parking garage.
• When a roof carrier is installed.
• When driving with tyre chains installed.
• When the tyres are worn.
• After replacing a tyre or tyres.
• When using tyres that are smaller or
larger than the factory specifications.
• When the tyre pressure in any of the 4
tyres is not correct.zInappropriate route guidance may occur in
the following cases:
• When turning at an intersection off the
designated route guidance.
• If you set more than 1 destination but skip
any of them, auto reroute will display a
route returning to the destination on the
previous route.
• When turning at an intersection for which
there is no route guidance.
• When passing through an intersection for
which there is no route guidance.
• During auto reroute, the route guidance
may not be available for the next turn to
the right or left.
• During high speed driving, it may take a
long time for auto reroute to operate. In
auto reroute, a detour route may be
shown.
• After auto reroute, the route may not be
changed.
• If an unnecessary U-turn is shown or
announced.
• If a location has multiple names and the
system announces 1 or more of them.
• When a route cannot be searched.
• If the route to your destination includes
gravel, unpaved roads or alleys, the route
guidance may not be shown.
zIf the vehicle cannot receive GPS signals,
the current position can be adjusted
manually. (→P.1 7 3 )
IS_Navi_EE_53C71E.book 185 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

186
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
• Your destination point might be shown on
the opposite side of the street.
• When a portion of the route has regula-
tions prohibiting the entry of the vehicle
that vary by time, season or other reasons.
• The road and map data stored in the navi-
gation system may not be complete or
may not be the latest version.
zAfter replacing a tyre: →P.1 74
INFORMATION
●
This navigation system uses tyre turning
data and is designed to work with factory-
specified tyres for the vehicle. Installing
tyres that are larger or smaller than the
originally equipped diameter may cause
inaccurate display of the current position.
The tyre pressure also affects the diame-
ter of the tyres, so make sure that the tyre
pressure of all 4 tyres is correct.
IS_Navi_EE_53C71E.book 186 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

187
6. TIPS FOR THE NAVIGATION SYSTEM
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
2. MAP DATABASE VERSION AND COVERED AREA
1Press the “MENU” button on the
Remote Touch.
2Select “Setup”.
3Select “Navigation”.
4Select “Map data”.
5Check that the map data screen is dis-
played.
MAP DATA
Coverage areas and legal information
can be displayed.
No.Function
Map version
Select to display legal information.
Select to display map data coverage
areas.
INFORMATION
●
Map data updates are available for a fee.
Contact your Lexus dealer for further
information.
IS_Navi_EE_53C71E.book 187 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

192
IS300h/250_Navi_EE
1. BASIC OPERATION
1. QUICK REFERENCE
■CONTROL SCREEN Operations such as selecting a preset station and adjusting the sound balance are car-
ried out on the screen.
XUsing the instrument panel
Press the “RADIO” or “MEDIA” button to display the audio/visual screen.
XUsing the Remote Touch
Press the “MENU” button on the Remote Touch, then select “Audio” to display the au-
dio/visual screen.
IS_Navi_EE_53C71E.book 192 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

193
1. BASIC OPERATION
AUDIO/VISUAL SYSTEM
IS300h/250_Navi_EE
4
■CONTROL PANEL
FunctionPage
Using the radio202
Playing an audio CD or MP3/WMA/AAC disc209
Playing a DVD215
Playing a USB memory222
Playing an iPod229
Playing a Bluetooth® device236
Using the AUX port242
Playing the VTR245
Using the steering wheel audio switches248
Audio system settings250
INFORMATION
●The illustration is for left-hand drive vehicles.
●The button positions and shapes will differ for right-hand drive vehicles.
●Also, the display and button positions will differ depending on the type of the system.
IS_Navi_EE_53C71E.book 193 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

195
1. BASIC OPERATION
AUDIO/VISUAL SYSTEM
IS300h/250_Navi_EE
4
XUsing the instrument panel
1Each time the “RADIO” or “MEDIA”
button is pressed, the audio control
mode changes.
“RADIO” button: To display the radio oper-
ation screen.
“MEDIA” button: To display the external
media operation screen.
XUsing the Remote Touch
1Press the “MENU” button on the
Remote Touch.
2Select “A u d i o ”.
3Select “Source”.
4Select the desired source.
SELECTING AN AUDIO
SOURCE
INFORMATION
●Dimmed screen buttons cannot be oper-
ated.
IS_Navi_EE_53C71E.book 195 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

200
1. BASIC OPERATION
IS300h/250_Navi_EE
XDVD video/iPod video/VTR
1Select “Options” on the control screen.
2Select “Wide” on the options screen.
XUSB video
1Select “Options” on the control screen.
2Select “Screen format” on the options
screen.
3Select the desired item to be adjusted.XDVD video/USB video/iPod video/VTR
1Select “Options” on the control screen.
2Select “Display” on the option screen.
AUDIO SCREEN
ADJUSTMENT
SCREEN SIZE SETTINGS
The screen size can be selected for each
type of media.
No.Function
Select to display a 4 : 3 screen, with
either side in black.
Select to enlarge the image horizon-
tally and vertically to full screen.
Select to enlarge the image by the
same ratio horizontally and vertically.
CONTRAST, BRIGHTNESS,
COLOUR AND TONE
ADJUSTMENT
The brightness, contrast, colour and
tone of the screen can be adjusted.
IS_Navi_EE_53C71E.book 200 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

202
IS300h/250_Navi_EE
2. RADIO OPERATION
1. AM/FM/DAB RADIO
■CONTROL SCREEN
OVERVIEW
The radio operation screen can be reached by the following methods:
XUsing the instrument panel
Press the “RADIO” button to display the audio control screen.
XUsing the Remote Touch
Press the “MENU” button on the Remote Touch, then select “Audio” to display the au-
dio control screen.
IS_Navi_EE_53C71E.book 202 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

204
2. RADIO OPERATION
IS300h/250_Navi_EE
No.Function
Select to display the manual tuning screen.
Select to display the station list screen.
Select to display the preset station screen.
Select to display the audio source selection screen.
Select to display the audio setting screen.
Select to tune to preset stations/ensembles.
Select to display the time shift operation screen.
Tune/Scroll knob:
•“Presets” screen: Turn to select preset stations/ensembles.
•“Stations” screen: Turn to move up/down the list.
•Manual tuning screen: Turn to step up/down frequencies or change services.
•“DAB time shift” screen: Turn to jump forward/backwards.
Press to turn mute on/off.
•Press to move up/down the preset stations/ensembles.
•Press to move up/down the station list.
•Press and hold 0.8 sec. or more to seek up/down available stations/ensembles continu-
ously while the button is being pressed.
•Press to select a radio mode.
•While in a radio mode, pressing the “RADIO” button changes radio modes.
Power/Volume knob:
•Turn to adjust volume.
•Press to turn the audio system on/off.
•Press and hold to restart the audio system.
INFORMATION
●The radio automatically changes to stereo reception when a stereo broadcast is received.
●If the signal becomes weak, the radio reduces the amount of channel separation to prevent
the weak signal from creating noise. If the signal becomes extremely weak, the radio
switches from stereo to mono reception.
IS_Navi_EE_53C71E.book 204 ページ ２０１４年５月２９日　木曜日　午前１１時２２分