navigation system Lexus IS300h 2014 Navigation manual

129
2. DESTINATION SEARCH
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
1Display the “Destination” screen.
(→P.118)
2Select “POI near cursor”.
3Set the search point by one of the fol-
lowing methods.
4Scroll the map to the desired point
(→P.103) and select “OK”.
5Select the desired POI categories and
select “List”.
“List all categories”: Select to display all
POI categories. To add more POI catego-
ries, select “More”.
6Select the desired POI.
zThe direction arrows of POIs are displayed
only when the current position is set as the
search point.
“On this route”: Select to search for POIs
along the route. When set to on, the indica-
tor will illuminate.
SEARCHING BY POI NEAR
CURSOR
The destination can be set by selecting
the search point and the POI category. It
is possible to display the names of POIs
located within approximately 20 miles
(30 km) from the selected search point.
No.Function
Select to enter the town name.
(→P.130)
Select to set a point by using the cur-
rent position.
Select to set a point by using the last
displayed map.
Select to set a point by using a cur-
rent destination.
Select to change pages.
IS_Navi_EE_53C71E.book 129 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

131
2. DESTINATION SEARCH
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
3. STARTING ROUTE GUIDANCE
1Select “Enter” on the destination map
screen.
zFor details about this screen: →P.1 3 2
2Select “Start” on the starting route
guidance screen.
zFor details about this screen: →P.1 3 3
After entering the destination, the
screen changes and displays the map lo-
cation of the selected destination.
STARTING ROUTE
GUIDANCE
CAUTION
●Be sure to obey traffic regulations and
keep road conditions in mind while driv-
ing. If a traffic sign on the road has been
changed, the route guidance may not
indicate such changed information.
INFORMATION
●
The route for returning may not be the
same as that for going.
●The route guidance to the destination
may not be the shortest route or a route
without traffic congestion.
●Route guidance may not be available if
there is no road data for the specified
location.
●When setting the destination on a map
with a scale more than 0.5 mile (500 m),
the map scale changes to 0.5 mile (500
m) automatically. If this occurs, set the
destination again.
●If a destination that is not located on a
road is set, the vehicle will be guided to
the point on a road nearest to the destina-
tion. The road nearest to the selected
point is set as the destination.
IS_Navi_EE_53C71E.book 131 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

133
2. DESTINATION SEARCH
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
*: Can only be used when receiving TPEG
(Transport Protocol Experts Group) infor-
mation. Depending on the country or area,
receiving TPEG information may not be
possible.
STARTING ROUTE
GUIDANCE SCREEN
No.Information/FunctionPage
Current position
Destination point
Type of route and its dis-
tance
Distance of the entire route
Select the desired route
from 3 possible routes.134
Select to change the route.144
Select to start guidance. If
“Start” is selected until a
beep sounds, demo mode
will start. Press the or
“MENU” button on the
Remote Touch to end
demo mode.

*Select to display traffic pre-
diction information.112
Select to display the Street
View.385
*
Select to update the traffic
or parking lot information
manually.
179
No.Information/FunctionPage
IS_Navi_EE_53C71E.book 133 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

135
2. DESTINATION SEARCH
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
1Select “Menu” on the map screen.
2Select “Suspend guidance”.
1Select “Resume guidance”.
SUSPENDING GUIDANCE
RESUMING GUIDANCE
IS_Navi_EE_53C71E.book 135 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

137
3. ROUTE GUIDANCE
IS300h/250_Navi_EE
NAVIGATION SYSTEM
31Select .
2Select the desired item.
■ARRIVAL AND TRAVEL TIME
1Select “Arrival time” or “Travel time”.
2Select the route information bar.
CHANGING ROUTE
INFORMATION
The current street name, travel/arrival
time to destination, or traffic information
bar can be displayed on the map screen.
No.FunctionPage
Select to display the cur-
rent street name.
Select to display the esti-
mated arrival time.
137Select to display the esti-
mated travel time.
Select to display the traffic
information bar.139
When the vehicle is on the guidance
route, the distance with the estimated
travel/arrival time to the destination is
displayed.
When driving on the guidance route
with more than 1 destination set, a list of
the distance with estimated travel/arriv-
al time from the current position to each
destination is displayed.
IS_Navi_EE_53C71E.book 137 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

139
3. ROUTE GUIDANCE
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
■TRAFFIC INFORMATION
1Select “Traffic bar”.
2Check that the traffic information is dis-
played.
zWhen multiple destinations are set, traffic
information icons are displayed up to the
nearest destination area.
zWhen the distance to the destination is 65
miles (100 km) or more, traffic information
icons are displayed up to 65 miles (100
km) away from the current position.
When traffic information is received, the
traffic information bar is displayed.
The colour of the arrow indicates specif-
ic road conditions. Red indicates a
closed road, accident, etc. Orange indi-
cates a traffic jam. Blue indicates normal
traffic flow. (Note that roads that are not
covered by traffic information are also
shown in blue.)
No.Information
Icon that shows road hazard points.
Arrow that shows traffic congestion.
Displays estimated travel time delay
caused by road repairs, an accident,
etc.
IS_Navi_EE_53C71E.book 139 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

141
3. ROUTE GUIDANCE
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
XWithout signpost motorway data
No.Information/Function
Next exit or junction name
Select to hide the motorway guid-
ance screen. To return to the motor-
way guidance screen, select .
Distance from the current position to
the exit or junction
Remaining distance bar to the guid-
ance point
INFORMATION
●
If “Automatic zoom” is set to on, these
screens are not displayed. (→P.1 7 0 )
WHEN APPROACHING
INTERSECTION
When the vehicle approaches an inter-
section, the intersection guidance
screen will be displayed.
No.Information/Function
Next street name
Lane guidance
Select to hide the intersection guid-
ance screen. To return to the inter-
section guidance screen, select
.
Distance to the intersection
Remaining distance bar to the guid-
ance point
INFORMATION
●
If “Automatic zoom” is set to on, this
screen is not displayed. (→P.1 7 0 )
IS_Navi_EE_53C71E.book 141 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

143
3. ROUTE GUIDANCE
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
2. TYPICAL VOICE GUIDANCE PROMPTS
As the vehicle approaches an intersec-
tion, or point, where maneuvering the
vehicle is necessary, the system’s voice
guidance will provide various messages.
CAUTION
●Be sure to obey the traffic regulations and
keep the road condition in mind espe-
cially when you are driving on IPD roads
(roads that are not completely digitized in
our database). The route guidance may
not have the updated information such as
the direction of a one way street.
INFORMATION
●
If a voice guidance command cannot be
heard, select on the map screen to
hear it again.
●To adjust the voice guidance volume:
→P. 8 3
●Voice guidance may be made early or
late.
●If the system cannot determine the cur-
rent position correctly, you may not hear
voice guidance or may not see the mag-
nified intersection on the screen.
IS_Navi_EE_53C71E.book 143 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

145
3. ROUTE GUIDANCE
IS300h/250_Navi_EE
NAVIGATION SYSTEM
3
5Select the items to be set.
6Check that the entire route map is dis-
played. (→P.133)
1Display the “Route” screen. (→P.144)
2Select “A d d ”.
3Search for an additional destination in
the same way as a destination search.
(→P.116)
4Select “Add destination here” to insert
the new destination into the route.No.FunctionPage
Select to set search condi-
tions.147
Select to set detours.147
Select to set road prefer-
ences.148
Select to add destinations.145
Select to delete destina-
tions.146
Select to reorder destina-
tions.146
Select to display route
overview.149
ADDING DESTINATIONS
IS_Navi_EE_53C71E.book 145 ページ ２０１４年５月２９日　木曜日　午前１１時２２分

147
3. ROUTE GUIDANCE
IS300h/250_Navi_EE
NAVIGATION SYSTEM
31Display the “Route” screen. (→P.144)
2Select “Search condition”.
3Select the desired type and select “OK”.
1Display the “Route” screen. (→P.144)
2Select “Detour”.
3Select the desired detour distance.
SETTING SEARCH
CONDITION
Road conditions of the route to the des-
tination can be set.
DETOUR SETTING
During the route guidance, the route
can be changed to detour around a sec-
tion of the route where a delay is caused
by road repairs, an accident, etc.
No.Function
Select to detour within 1 mile of the
current position.
Select to detour within 3 miles of the
current position.
Select to detour within 5 miles of the
current position.
Select to detour on the entire route.
Select to make the system search for
the route based on the traffic con-
gestion information received from
traffic information. (→P.109)
IS_Navi_EE_53C71E.book 147 ページ ２０１４年５月２９日　木曜日　午前１１時２２分