display lexus LC500 2018 Navigation Manual

89
3
-$@-$I@/BWJ@0.&@ &&

3-2. Destination search
Navigation system
7Select “Calculate”.
●If a destination that is not located on a
road is set, the vehicle will be guided to the point on a road nearest to the destina-tion.
●If a destination is set that cannot be reached, a pop-up will be displayed to
indicate this.

90
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
3-3.Route guidance
When the destination is set, the entire
route map from the current position to
the destination is displayed.
Depending on the navigation settings,
either a single route or route alterna-
tives will be displayed on the screen.
( P.113)
Recommended route screen
Route alternatives screen
●The starting route guidance screen is dis- played in 2D north-up.
The recommended route will be dis-
played on the map.
1 Select “Destination” to start route
guidance.
 Displays information about the des-
tination, such as estimated arrival
time and distance.
Select to display the three route
calculation methods. Select the
desired item to adjust the route
preferences. ( P.91)
Select to display the avoidance cri-
teria. Select the desired item to
adjust the avoidance criteria.
( P.91)
Select to display parking lot infor-
mation. The location and available
spaces of parking lots around the
destination can be checked.
( P.226)
Select to display the Street View.
The Street View images of the des-
tination can be viewed. ( P.224)
Select to display weather informa-
tion. The weather information
around the destination can be
checked. ( P.225)
Starting route guidance
Starting route guidance
WARNING
●Be sure to obey traffic regulations and
keep road conditions in mind while driving. If a traffic sign on the road has been changed, the route guidance
may not indicate such changed infor- mation.
Recommended route screen
A
B
C
D
E

91
3
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
Navigation system
●The default route preferences and avoid- ance criteria can be selected. ( P.113)
●If “Destination” is selected and held, demo mode will start. Select “Quit” on the screen to end demo mode.
1 Select .
2 Select the desired item to adjust the
route preferences.
Select to display the fastest route.
Select to display the route that is
the shortest distance to the set des-
tination.
Select to display the fuel-efficient
route.
 The route will be recalculated and
then the starting route guidance
screen will be displayed.
1 Select .
2 Select the desired items to avoid.
Select to avoid the toll roads.
Select to avoid the motorway.
Select to avoid the ferry/train.
Select to avoid the tunnel.
 The route will be recalculated and
then the starting route guidance
screen will be displayed.
If the possible route is unreasonably
long, the system will propose a route
including items selected to avoid.
 The default avoidance criteria can
be selected. ( P.113)
Three types of route alternatives will be
displayed on the map.
1 Select one of the three types of
route alternatives.
 Displays information about the des-
tination, such as estimated arrival
Adjusting the route type
Adjusting avoidance criteria
A
B
CRoute alternatives screen
A
B
C
D

92
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
time and distance.
Select to display the avoidance cri-
teria. Select the desired item to
adjust the avoidance criteria.
( P.92)
Select to display parking lot infor-
mation. The location and available
spaces of parking lots around the
destination can be checked.
( P.226)
Select to display the Street View.
The Street View images of the des-
tination can be viewed. ( P.224)
Select to display weather informa-
tion. The weather information
around the destination can be
checked. ( P.225)
 The estimated arrival time and dis-
tance of the entire route will be dis-
played in the list.
1 Select .
2 Select the desired items to avoid.
Select to avoid the toll roads.
Select to avoid the motorway.
Select to avoid the ferry/train.
Select to avoid the tunnel.
 The route will be recalculated and
then the starting route guidance
screen will be displayed.
If the possible route is unreasonably
long, the system will propose a route
including items selected to avoid.
 The default avoidance criteria can
be selected. (  P.113)
Adjusting avoidance criteria
A
B
C
D
A
B
C
D

93
3
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
Navigation system
Displays the distance to the next
turn with the arrow indicating the
turn direction.
When the arrow icon is selected,
the last navigation announcement
will be repeated.
Current position
Guidance route
Displays information about the des-
tination, such as estimated arrival
time, remaining travel time, dis-
tance, and traffic prediction infor-
mation.
Select to change the display esti-
mated arrival time/remaining travel
time.
Displays traffic events on the route.
The remaining length and the
remaining delay time are displayed.
The name of the current street or
the next street (when approaching
a turning point)
During freeway driving, the highway
information screen will be displayed.
Name of the road traffic facilities.
Distance and time from the current
position to the road traffic facilities.
POI’s that are on the highway or
close to a highway exit.
●Select desired POIs to display the selected map of the exit vicinity.
●Select a button at the bottom of the list allows to go back to displaying nearest
road traffic facilities.
●To view highway information, open the
navigation section of the side display and select “Highway”.
When approaching the turn, a signpost
will automatically be displayed on the
main map screen.
Route guidance
Route guidance screen
A
B
C
D
E
F
During highway driving
Signposts*
A
B
C

94
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
Displays information about the
signposts.
*: If the data is available
When approaching a motorway junc-
tion, junction view images will automat-
ically be displayed on the side screen.
When approaching a turning point, the
lane recommendation will automati-
cally be displayed under the map.
Displays the lane recommendation
●If the vehicle goes off the guided route,
the route will be recalculated.
●For some areas, the roads have not been
completely digitized in our database. Take care when following a guided route.
●The displaying of the above items can be switched off. ( P.106)
The voice guidance provides various
messages as you approach an inter-
section, or other points where maneu-
vering the vehicle is necessary.
 The voice guidance can be muted
by selecting the .
 The last navigation announcement
can be repeated by selecting the
arrow icon.
●The voice guidance may not pronounce certain street names correctly or clearly due to the limitations of the text-to-
speech function.
●On motorways, interstates or other high-
ways with higher speed limits, the voice guidance will be made at earlier points than on city streets in order to allow time
to maneuver the vehicle.
●If the system cannot determine the cur-
rent vehicle position correctly (in cases of poor GPS signal reception), the voice guidance may be early or delayed.
●The default voice guidance volume can also be changed. ( P.60)
Motorway junction screen
Lane recommendation
A
A
Voice guidance

95
3
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
Navigation system
1A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select on the map.
3 Select “Pause guidance”.
 The route guidance can be
restarted by selecting “Resume
guidance”.
During route guidance, the route to the
destination can be checked and edited.
1 A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select the on the map.
3 Select “Route”.
4 Select the items to be set.
When a destination is set
Select to display the three route
calculation methods. Select the
desired item to adjust the route
preferences. ( P.91)
Select to display the avoidance cri-
teria.
Select the desired item to adjust the
WARNING
●Be sure to obey the traffic regulations and keep the road condition in mind especially when you are driving on IPD
roads (roads that are not completely digitized in our database). The route guidance may not have the updated
information such as the direction of a one way street.
Pausing route guidance
Editing route
Displaying the edit route screen
A
B

96
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
avoidance criteria. (P.91, 92)
Select to block a fixed distance on
the road ahead. A blocked route
will be marked in the map. ( P.98)
Select to display the turn list to the
destination. ( P.98)
Select to display the destination
information. The destination can be
checked and registered. ( P.96)
Select to delete a destination.
( P.97)
When a destination and stopovers
are set
Select to display the three route
calculation methods. Select the
desired item to adjust the route
preferences. ( P.91)
Select to display the avoidance cri-
teria. Select the desired item to
adjust the avoidance criteria.
( P.91, 92)
Select to block a fixed distance on
the road ahead. A blocked route
will be marked in the map. ( P.98)
Select to display the turn list to the
destination. ( P.98)
Select to display the destination
information. The destination and
stopovers can be checked and reg-
istered. ( P.96)
Select to display the destination
and stopovers information. The
destination and stopovers can be
checked and edited. ( P.96)
1 A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select the on the map.
 If route is set, select “Route”.
3 Select / “Info”.
4 Check that the destination informa-
tion is displayed.
Address of destination*
Arrival time, remaining time and
distance to destination*
Current location information
Select to register the current posi-
tion in the favourites list.
*: This is only displayed if there is an active
C
D
E
F
A
B
C
D
E
Displaying destination informa-
tion
F
A
B
C
D

97
3
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
Navigation system
route guidance.
When more than 1 destination has
been set, the arrival order of the desti-
nations can be changed.
1 A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select on the map.
3 Select “Route”
4 Select “Stopover list”.
5 Press the button on the Remote
Touch.
6 Select the desired destination and
select or to change the
arrival order.
7 Press the button on the Remote
Touch.
1 A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select the on the map.
3 Select “Route”
When a destination is set
4 Select “Delete”.
5 Select “Yes”.
When a destination and stopovers
are set
4 Select “Stopover list”.
Reordering stopovers
Deleting stopovers and destina-
tion

98
-$@-$I@/BWJ@0.&@ &&

3-3. Route guidance
5Select .
When desired stopover is selected, the stopover information can be displayed.
( P.80)
6Select “Yes”.
7 Press the button on the Remote
Touch.
During the route guidance, the route
can be changed to detour around a
section of the route.
1 A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select the on the map.
3 Select “Route”.
4 Select “Block road”.
5 Select the desired block distance to
detour.
Select to block a designated dis-
tance of the road from the current
position.
 Select “Deactivate” to cancel the
blocked setting.
 The blocked route will be marked in
the map.
 After the blocked route has been
detoured, the blocked route feature
will automatically be deactivated.
1 A short while later after the “MAP”
button is pressed, the display auto-
matically switches to map screen.
( P.69)
2 Select the on the map.
3 Select “Route”.
4 Select .
Blocking road segments
Displaying the turn list
A