display lexus LC500 2018 Navigation Manual

113
3
-$@-$I@/BWJ@0.&@ &&

3-5. Setup
Navigation system
1Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Navigation” on the sub
menu.
4 Select “Route preference”.
5 Select the item to be set.
Select to change the recom-
mended route type to fastest route,
shortest route or ecological route.
Select to use historical traffic infor-
mation in the route calculation.
Select to display the 3 routes (fast-
est, shortest and ecological) on the
map after route calculation.
( P.91)
Select to set the avoidance criteria
for the route calculation. ( P.113)
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Navigation” on the sub
menu.
4 Select “Route preference”.
5 Select “Avoidance criteria”.
6 Select the desired items to avoid.
Route preferences settings
Displaying route preferences
screen
A
B
C
Setting the avoidance criteria for
the route calculation
D

114
-$@-$I@/BWJ@0.&@ &&

3-5. Setup
1Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Navigation” on the sub
menu.
4 Select “Manage stored destina-
tions”.
5 Select the desired item.
Select to delete all favourites.
Select to delete all recent destina-
tions.
The backup of the favourites on the
USB device will be loaded into the
list of favourites on the navigation
system.
The navigation favourites will be
sent to the connected USB device.
Displaying Manage stored desti-
nations screen
A
B
C
D

115
3
-$@-$I@/BWJ@0.&@ &&

3-6. Tips for the navigation system
Navigation system
3-6.Tips for the navigation s ystem
The Global Positioning System (GPS)
developed and operated by the U.S.
Department of Defense provides an
accurate current vehicle position, nor-
mally using 4 or more satellites, and in
some case 3 satellites. The GPS sys-
tem has a certain level of inaccuracy.
While the navigation system will com-
pensate for this most of the time, occa-
sional positioning errors of up to 100 m
(100 yards) can and should be
expected. Generally, position errors
will be corrected within a few seconds.
The GPS signal may be physically
obstructed, leading to inaccurate vehi-
cle position on the map display. Tun-
nels, tall buildings, trucks, or even the
placement of objects on the instrument
panel may obstruct the GPS signals.
The GPS satellites may not send sig-
nals due to repairs or improvements
being made to them.
Even when the navigation system is
receiving clear GPS signals, the vehi-
cle position may not be shown accu-
rately or inappropriate route guidance
may occur in some cases.
 Accurate current vehicle position
may not be shown in the following
cases:
• When driving on a small angled Y-
shaped road.
• When driving on a winding road.
• When driving on a slippery road such as
in sand, gravel, snow, etc.
• When driving on a long straight road.
• When motorway and surface streets run
in parallel.
• After moving by ferry or vehicle carrier.
• When a long route is searched during
high speed driving.
• After repeating a change of direction by
going forward and backward, or turning
on a turntable in the parking lot.
• When leaving a covered parking lot or
parking garage.
• When a roof carrier is installed.
• When driving with tire chains installed.
• When the tires are worn.
• After replacing a tire or tires.
GPS (Global Positioning
System)
This navigation system calculates
the current vehicle position using
satellite signals, various vehicle sig-
nals, map data, etc. However, an
accurate position may not be shown
depending on satellite condition,
road configuration, vehicle condi-
tion or other circumstances.
Limitations of the navigation sys-
tem
NOTICE
●The installation of window tinting may
obstruct the GPS signals. Most win- dow tinting contains some metallic content that will interfere with GPS
signal reception of the antenna. We advise against the use of window tint-ing on vehicles equipped with naviga-
tion systems.

116
-$@-$I@/BWJ@0.&@ &&

3-6. Tips for the navigation system
• When using tires that are smaller or
larger than the fact ory specifications.
• When the tire pressure in any of the four
tires is not correct.
 Inappropriate route guidance may
occur in the following cases:
• When turning at an intersection off the
designated route guidance.
• If you set more than one destination but
skip one of them, auto reroute will dis-
play a route returning to the destination
that was skipped.
• When turning at an intersection for
which there is no route guidance.
• When passing through an intersection
for which there is no route guidance.
• During auto reroute, the route guidance
may not be available for the next turn to
the right or left.
• It may take a long time to operate auto
reroute during high speed driving. In
auto reroute, a detour route may be
shown.
• After auto reroute, the route may not be
changed.
• An unnecessary U-turn may be shown
or announced.
• A location may have multiple names and
the system will announce one or more.
• Some routes may not be searched.
• If the route to your destination includes
gravel, unpaved roads or alleys, the
route guidance may not be shown.
• Your destination point might be shown
on the opposite side of the street.
• When a portion of the route has regula-
tions prohibiting the entry of the vehicle
that vary by time or season or other rea-
sons.
• The road and map data stored in the
navigation system may not be complete
or may not be the latest version.
●This navigation system uses tire turning data and is designed to work with fac-
tory-specified tires for the vehicle. Install- ing tires that are larger or smaller than the originally equipped diameter may cause
inaccurate display of the current vehicle position. The tire pressure also affects the diameter of the tires so make sure the
tires pressure of all four tires is correct.

120
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
4-1.Basic operation
The audio control screen can be
reached by the following methods:
Using the audio control switch
1 Press the “RADIO” or “MEDIA”
button.
Using the Remote Touch
1 Press the “MENU” button on the
Remote Touch, then select “Radio”
or “Media”.
The audio functions can also be displayed and operated on the side display. ( P.33)
■Control screen
■Audio control switch
•Using the radio ( P.126)
• Playing an audio CD or
MP3/WMA/AAC disc ( P.130)
• Playing a DVD ( P.132)
• Playing a USB memory ( P.135)
• Playing an iPod ( P.137)
• Playing a Bluetooth® device
( P.139)
• Using the Miracast™ ( P.142)
•Using the AUX port ( P.144)
• Using the steering wheel audio
switches ( P.146)
• Audio system settings ( P.148)
●The position and shapes of the buttons may differ slightly between right-hand
drive vehicles and left-hand drive vehi- cles.
Quick reference
Functional overview

121
4
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
Audio/visual system
■Certification
• CAUTION:
THIS PRODUCT IS A CLASS I LASER PRODUCT. USE OF CONTROLS OR
ADJUSTMENTS OR PERFOR- MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADI- ATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY
YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
“PWR·VOL” knob: Press to turn the
audio/visual system on and off. The sys-
tem turns on in the last mode used.
Turn this knob to adjust the volume.
 A function that enables automatic
return to the previous screen from
the audio/visual screen can be
selected. ( P.56)
Using the audio control switch
1 Display the audio control screen.
2 Each time the “RADIO” or
“MEDIA” button is pressed, the
audio source changes.
“RADIO” button: To change radio
modes.
“MEDIA” button: To change media
modes.
From the audio source selection
screen
1 Display the audio control screen.
2 Select “Source” on the sub menu.
3 Select the desired source.
●Dimmed screen buttons cannot be oper- ated.
Some basics
This section describes some of the
basic features of the audio/visual
system. Some information may not
pertain to your system.
Your audio/visual system works
when the engine switch switch> is in ACCESSORY or
IGNITION ON mode .
NOTICE
●To prevent the 12-volt battery from
being discharged, do not leave the audio/visual system on longer than necessary when the engine is not run-
ning .
Turning the system on and off
Selecting an audio source

122
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
1Display the audio control screen.
2 Select “Source” on the sub menu.
3 Select “Reorder”.
4 Select the desired audio source
then or to reorder.
■Inserting a disc
 After insertion, the disc is automati-
cally loaded.
■Ejecting a disc
1 Press the button and remove
the disc.
●The player is intended for use with 4.7 in. (12 cm) discs only.
●When inserting a disc , gently insert the disc with the label facing up.
There are 2 USB ports and an AUX
port in the console box.
1 Slide the armrest as far back while
pressing the button.
2 Lift the armrest while pulling the
knob.
Reordering the audio source
Disc slot
NOTICE
●Never try to disassemble or oil any part of the DVD player. Do not insert anything other than a disc into the slot.
USB/AUX port

123
4
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
Audio/visual system
3Open the cover and connect a
device.
 Turn on the power of the device if it
is not turned on.
●Up to two portable players can be con-
nected to the USB port at the same time.
●Even if a USB hub is used to connect
more than two USB devices, only the first two connected devices will be recog-nized.
1 Display the audio control screen.
2 Select “Sound” on the sub menu.
3 Select the desired switch to be set.
Select to set the treble/mid/bass.
( P.123)
Select to set the fader/balance.
( P.124)
The system adjusts to the optimum
volume and tone quality according
to vehicle speed to compensate for
increased vehicle noise. ( P.124)
This function can create a feeling of
presence. ( P.124)
■Treble/Mid/Bass
How good an audio program sounds is
largely determined by the mix of the
treble, mid and bass levels. In fact, dif-
ferent kinds of music and vocal pro-
grams usually sound better with
different mixes of treble, mid and bass.
1 Select the “Treble/Mid/Bass” and
select the desired item to be set.
Select “+” or “-” to adjust high-
NOTICE
●Depending on the size and shape of the device that is connected to the sys-tem, the console box/auxiliary box may
not close fully. In this case, do not forci- bly close the console box/auxiliary box as this may damage the device or the
terminal, etc.
Sound settings
A
B
C
D
A

124
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
pitched tones.
Select “+” or “-” to adjust mid-
pitched tones.
Select “+” or “-” to adjust low-
pitched tones.
■Fader/Balance
A good balance of the left and right
stereo channels and of the front and
rear sound levels is also important.
Keep in mind that when listening to a
stereo recording or broadcast, chang-
ing the right/left balance will increase
the volume of 1 group of sounds while
decreasing the volume of another.
1 Select the “Fader/Balance” and
select the desired item to be set.
Select to adjust the sound balance
between the front and rear speak-
ers.
Select to adjust the sound balance
between the left and right speakers.
■Automatic sound levelizer
The system adjusts to the optimum vol-
ume and tone quality according to
vehicle speed to compensate for
increased vehicle noise.
1 Select to set the Automatic sound
levelizer on/off.
■Surround
This function can create a feeling of
presence.
1 Select to set the surround on/off.
■Screen size settings
The screen size can be selected for
each type of media.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Audio” on the sub menu.
4 Select “Common”.
5 Select “Screen format”.
DVD video/USB video
Miracast™
Select to display a 4 : 3 screen, with
either side in black.
B
C
A
B
Audio screen adjustment
A

125
4
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
Audio/visual system
Select to enlarge the image hori-
zontally and vertically to full screen.
Select to enlarge the image by the
same ratio horizontally and verti-
cally.
■Contrast, Brightness, Color and
Tone adjustment
The brightness, contrast, color and
tone of the screen can be adjusted.
DVD video/USB video/Miracast™
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Audio”.
4 Select “Common”.
5 Select “Display”.
 “Colour”
“R”: Select to strengthen the red color of
the screen.
“G”: Select to strengthen the green color
of the screen.
 “Tone”
“+”: Select to strengthen the tone of the
screen.
“-”: Select to weaken the tone of the
screen.
 “Contrast”
“+”: Select to strengthen the contrast of the
screen.
“-”: Select to weaken the contrast of the
screen.
 “Brightness”
“+”: Select to brighten the screen.
“-”: Select to darken the screen.
●Depending on the audio source, some functions may not be available.
1 Press this switch to operate the
speech command system.
 The speech command system and
its list of commands can be oper-
ated. ( P.168)
B
C
Speech command system