lock LEXUS LS430 2005 Owners Manual

OCCUPANT RESTRAINT SYSTEMS
224When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered
in another button, that memory will also be erased.
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the wireless remote control key in which you want
to cancel the registrati on in possession and push the
“SET” button.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with the “SET”
button held down.
When the previous key ID memory is erased, two beeps
sound.
REAR SEAT POSITION MEMORY SYSTEM
A microcomputer will memorize the position of the rear seats
and the height of the rear head restraints.
Recording the rear seat position in the computer’s memory can
only be done when the ignition switch is in the “ON” position.
Setting the rear seat position
16L301a
1. Adjust the rear seat position and the height of the head
restraint of the rear seat to the desired position.
2. Keep pushing the “SET” button until a beep sounds.
The beep sound means that the position has been memorized.
The memory will be erased when the battery is removed for
inspection or service.

STEERING WHEEL AND MIRRORS
229
Automatic tiltaway*
In case of the smart key system:
16L644
When the smart key system is used, turning the ignition
switch
1 to the “LOCK” position moves the steering
column forward away from the driver and also tilts it up for
easy exit and entry.
When you push in the ignition switch, the steering column
returns to the previously set position.
NOTE:
* This feature can be deactivated.
Ask your Lexus dealer for details. When the key is inserted into the ignition:
16L715
When you remove the smart key 2
or ignition key 3,
the steering column moves forward away from the driver
and also tilts up for easy exit and entry.
When you insert the key in the ignition switch, the steering
column returns to the previously set position.
NOTE:
* This feature can be deactivated.
Ask your Lexus dealer for details.

STEERING WHEEL AND MIRRORS
232
Folding and extending automatic rear view
mirrors
16L642
With the rear view mirror folding switch in the “AUTO”
position:
When you turn the ignition switch to “ACC” or “ON” position,
the folded rear view mirrors are automatically extended.
 When you turn the ignition switch to “LOCK” position, the
rear view mirrors are automatically folded.
The rear view mirrors can be folded or extended manually.
CAUTION
 To avoid personal injury and mirror malfunction, do
not touch the mirror while it is moving.
 Do not drive with the mirrors folded backward. Both
the driver and passenger side rear view mirrors must
be extended and properly adjusted before driving.
Folding rear view mirrors154.
16L643
To fold the mirrors, push the switch on the right side. To
extend the rear view mirrors, push the switch on the left
side.
The rear view mirrors can be folded backward for parking in
compact areas.
CAUTION
To avoid personal injury and any mirror malfunction,
do not touch the mirror while it is moving.
 Do not drive with the mirrors folded backward. Both
the driver and passenger side rear view mirrors must
be extended and properly adjusted before driving.

STEERING WHEEL AND MIRRORS
233
155.Outer foot lights
16L659
The outer foot lights illuminate the ground near the doors
for about 15 seconds to ensure safe footing for the driver
and passengers who are about to get in the vehicle.*
The outer foot lights come on when:
you are getting closer to the vehicle carrying a smart key
and you enter the effective range of the smart key system
(about 1 m (3 ft) from each outside door handle),
 the doors are unlocked with the wireless remote control
function key, or
 the doors are unlocked with the power door lock switch on
the driver’s side. The outer foot lights go off 15 seconds after the lights come on
or when:

the lock switch on the outside door handle is pushed,
 the doors are locked with th e wireless remote control
function key,
 the doors are locked by inserting a key into the door
keyhole,
 the doors are locked with the power door lock switch on the
driver’s side, or
 the selector lever is moved out of “P” position with the
ignition on.
NOTE:
* The outer foot lights illuminating time can be changed.
Ask your Lexus dealer for details.

AIR CONDITIONING
248
(b) Windshield defogging and defrosting
21L068a
To remove interior fog on the windshield
Push the “FRONT WINDSHIELD” button.
To remove frost or exterior fog on the windshield
1. Place the temperature control button at the maximum
temperature.
2. Push the “FRONT WINDSHIELD” button.
3. Push the fan speed control button on the right side to obtain
a maximum air flow.
4. Leave the “A/C” button off.
When the “FRONT WINDSHIELD” button is pushed while
operating in automatic mode, the air conditioning is set to
operate and the OUTSIDE AIR mode is set. If you push the “FRONT WINDSHIELD” button once again
while in the FRONT WINDSHIELD mode, the mode then
returns to the last mode used.
CAUTION
Do not use the “FRONT WINDSHIELD” button during
cooled air operation in extremely humid weather. The
difference between the temperature of the outside air
and that of
the windshield could cause the outer surface
of the windshield to fog up blocking your vision.
When you turn the ignition switch on after the removal and
installation of the battery terminal, the indicator light may flash
and the operating sound of the motor may be heard. This does
not indicate a malfunction.
You may hear the operating sound of the motor about 70
seconds after the ignition switch is turned off. This does not
indicate a malfunction.

AIR CONDITIONING
252
(d) Operating tips
Make sure the air inlet grilles in front of the windshield are
not blocked by leaves or other obstructions.
 If air flow control is not satisfactory, check the dashboard
vents. (See “Center vents”, “Side vents” and “Rear vents”.)\
 To help cool down the interior after parking in the hot sun,
drive for the first few minutes with the windows open. After
the excess heat has blown away, close the windows.
 When driving on dusty roads, close all windows. If dust
thrown up by the vehicle is still drawn into the vehicle after
closing the windows, it is recommended that the air intake
control button be left to the OUTSIDE AIR mode and the fan
speed control button be pressed to anywhere except the
“OFF” button.
 If following another vehicle on a dusty road, or driving in
windy and dusty conditions, it is recommended that the air
intake control button be temporarily pressed in to the
RECIRCULATED AIR mode, which will close off the outside
passage and prevent outside air and dust from entering the
vehicle interior.
Center vents
21L064a
The center vents may be opened or closed as shown.
21L057b
Push the swing button to swing the vanes.
The vanes directly aimed at the driver and front passenger will
swing wider as the room temperature nears the desired
temperature. The swinging angle will also change from narrow
to wide depending on the room temperature.

AIR CONDITIONING
256
(d) Replacing the photocatalyst filter for therear seats
This rear air conditioning is equipped with dustproof and
deodorant filter with photocatalyst.
Replace the air filter when the use of rear air conditioning or air
purification function reduces air flow or deodorant
performance.
This filter is an interchangeable type. Do not clean the filter by
washing or air blowing. The use of filter after washing or
cleaning may cause a malfunction of the system. Be sure to
replace it with a new one.
The filter is located in the trunk.
Replace the filter using the following procedures.
1. Be sure to turn the ignition switch to “LOCK”.
21L210
 1 Air purifier 2Filter cover
2. Open the trunk and remove the filter cover in the trunk.
21L211
 1 Filter case 2Filter
3. Pull out the filter case toward you.
4. Replace the filter.
When you install the filter, face the filter surface (gray)
downward and fit the filter folds properly in the case as shown.
5. Install the filter in the reverse order of removal.
The gray surface in the filter may turn to yellow (yellow spots)
because of ultraviolet rays included in the light, however it is
no problem for use.

AUDIO
287
Rear controller (some models)
The rear controller is installed in the armrest of the rear
center seat so that you can operate the audio system in
the rear seat.
20L132c
“POWER” button: Use this button to turn the system on and
off.
“MODE” button: Use this button to change the mode. If a
tape or CD is not inserted, the “T APE” or “CD” mode is skipped.
You can lock the button operation. To activate the lock, push
and hold the “MODE” button until you hear a beep. “LOCK”
appears on the display. All the buttons in the rear controller are
inoperative. To cancel it, push and hold the “MODE” button
until you hear a beep again. You can use all the buttons.
“VOL” button: Use this button to adjust the volume. (a) When the radio mode is selected
“CH”
button: Push the “CH” button to select a station preset
on the preset button of the front audio system. Each push of
the button changes to the station with higher numbered preset
button.
”
“ button:
Push this button for manual tuning or seek
tuning.
 Push this button briefly. Each time you push the button, the
radio will step up or down to another frequency.
 Push this button and hold it until you hear a beep. The radio
will begin seeking up or down for a station, and will stop on
reception. Each time you push the button, the stations will
be searched out one after another.
(b) When the “TAPE” mode is selected
The applicable functions are shown in the lowest part of
the display. Push the switch just below to turn on each
function. In the “CD” mode, “DISC” and “TRACK” are
displayed.
“CH” button: Push this button to select the other side of a
cassette tape.
”
“ button:
Push the left or right side to skip forward or
backward to locate the song you want to hear. For details, see
“Automatic program selection” on page 280.

AUDIO
290Radio reception
Usually, a problem with radio reception does not mean there
is a problem with your radio
− it is just the normal result of
conditions outside the vehicle.
For example, nearby buildings and terrain can interfere with
FM reception. Power lines or telephone wires can interfere
with AM signals. And of course, radio signals have a limited
range. The farther you are from a station, the weaker its signal
will be. In addition, reception conditions change constantly as
your vehicle moves.
Here are some common reception problems that probably do
not indicate a problem with your radio:
FM
Fading and drifting stations − Generally, the ef fective range
of FM is about 40 km (25 miles). Once outside this range, you
may notice fading and drifting, which increase with the
distance from the radio transmitter. They are often
accompanied by distortion.
Multipath − FM signals are reflective, making it possible for
two signals to reach your antenna at the same time. If this
happens, the signals will cancel each other out, causing a
momentary flutter or loss of reception.
Static and fluttering − These occur when signals are blocked
by buildings, trees, or other large objects. Increasing the bass
level may reduce static and fluttering. Station swapping −
If the FM signal you are listening to is
interrupted or weakened, and there is another strong station
nearby on the FM band, your radio may tune in the second
station until the original signal can be picked up again.
AM
Fading − AM broadcasts are reflected by the upper
atmosphere − especially at night. These reflected signals can
interfere with those received directly from the radio station,
causing the radio station to sound alternately strong and weak.
Station interference − When a reflected signal and a signal
received directly from a radio station are very ne arly the same
frequency, they can interfere with each other, making it dif ficult
to hear the broadcast.
Static − AM is easily affected by external sources of electrical
noise, such as high tension power lines, lightening, or electrical
motors. This results in static.
Caring for your cassette player and tapes
For the best performance for your cassette player and tapes:
Clean the tape head and other parts regularly.
 A dirty tape head or tape path can decrease sound quality
and tangle your cassette tapes. The easiest way to clean
them is by using a cleaning tape. (A wet type is
recommended.)

SECTION 3 – 1
295
STARTING AND DRIVING
Starting and driving
Three−way catalytic converters296
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust caution 297
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before starting the engine 298
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smart ignition system with steering lock 298
. . . . . . . . . . . . . . . . . . . . .
Ignition switch with steering lock 301
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake 304
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
How to start the engine 304
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 305
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic throttle control system 315
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Lexus park assist system 316
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear view monitor system 323
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control 326
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Dynamic radar/laser cruise control 329
. . . . . . . . . . . . . . . . . . . . . . . . .
Electronically modulated air suspension 360
. . . . . . . . . . . . . . . . . . . . .
Traction control system 362
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle stability control system 364
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system 366
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Tire pressure warning system 370
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake pad wear limit indicators 373
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre−collision safety system 374
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .