ECO mode LEXUS LX470 2006 User Guide

AIR CONDITIONING
206SETTING OPERATION manual control
When one of the manual control buttons is depressed
while operating in automatic mode, the mode relevant to
the depressed button is set. Other conditions continue to
be adjusted automatically.
If manual air flow selection is desired
20X021a
The outlets from which air is delivered can be selected
manually by pressing the button. The function of each mode
is as follows:
1
Panel − Air flows mainly from the instrument panel vents.
2
Bilevel − Air flows from both the floor vents and the
instrument panel vents.
3 Floor − Air flows mainly from the floor vents.
It is recommended that you close the lower vent. For details
about this, see page 212.
4 Floor/Windshield − Air flows mainly from the floor vents
and windshield vents.
It is recommended that you close the lower vent. For details
about this, see page 212.
If quick heating or cooling is desired
Turn the “TEMP” knob until “MAX. HOT” or “MAX. COLD”
appears on the display.
If manual fan speed control is desired
21x600
 1 Fan speed at low 2Fan speed at high
The fan speed can be set to your desired speed by pushing the
appropriate side of fan speed control button. The higher the
fan speed is, the more air is delivered. Pushing the “OFF”
button turns off the fan.
To remove exterior windshield frost, use the high speed
setting.

AIR CONDITIONING
207
If manual switching of air intake is desired
20X023a
Each time you push the air intake control button, the mode
changes in order from the RECIRCULATED AIR mode to
AUTOMATIC mode to OUTSIDE AIR mode, then back to the
RECIRCULATED
AIR mode. Each indicator light shows which
mode is now selected.
1 RECIRCULATED mode If quick circulation of cooled air
is desired, select this mode.
2 EXHAUST GAS AUTOMATIC mode If the outside air
contains harmful substances like exhaust gas (i.e., when
the vehicle running just in front of your vehicle accelerates
rapidly), the system changes automatically from the
OUTSIDE AIR mode (with indicators
2
and 3 on) to
the RECIRCULATED mode (with indicators 1
and 2
on).
3 OUTSIDE AIR mode The system will take fresh outside
air into the vehicle. Turning off the air conditioning manually will cancel the
EXHAUST
GAS AUTOMATIC mode. If you select the “AUTO”
mode during fan operating, the air conditioning turns on and
the EXHAUST GAS AUTOMATIC mode will operate.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
In the following cases, the RECIRCULATED mode may
change to the OUTSIDE AIR mode automatically to prevent
interior fog.
 When the outside temperature becomes lower than 4 C
(39 F).
 When the air conditioning compressor malfunctions.
 When the air conditioning cooler refrigerant decreases.
To change the sensitivity of the sensor switching between
the RECIRCULA TED and OUTSIDE AIR in the AUTOMATIC
mode, push the air intake control button until the “AUTO”
indicator light flashes. The display changes as illustrated
below.
The sensitivity of the sensor can be adjusted only while the
vehicle has stopped.

AIR CONDITIONING
208
20X062d
When you turn the “TEMP” knob, the sensitivity changes from
“+3” down to “−3”. If you do not operate any button for a few
seconds or if you push a button other than the air intake control
button and temperature control knob, the previous display
returns.
If manual onoff of the air conditioning is desired
Push the “A/C” button to turn the air conditioning on and push
it again to turn the air conditioning off. If you turn off the air
conditioning manually, the EXHAUST GAS AUTOMATIC
mode will be cancelled.
If the outside temperature is lowered down to around 0 C
(32 F), the air conditioning will turn off automatically. At this
time, the indicator on the A/C button is off and the EXHAUST
GAS AUTOMATIC indicator light remains on. However, the
EXHAUST GAS AUTOMA TIC mode does not operate. When
the air conditioning turns on as with the raised temperature, the
EXHAUST GAS AUTOMATIC mode resumes. If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off
once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year −round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the “A/C” button will blink. If the indicator of the
“A/C” button blinks even when the “A/C” button is pushed
again, have the compressor checked by your nearest Lexus
dealer.

AIR CONDITIONING
211
20X073c
Your vehicle is equipped with an air conditioning filter.
The air conditioning filter may clog after long use and
reduce the air flow quantity.
To maintain the air conditioning efficiency, inspect and replace
the air conditioning filter according to the maintenance
schedule. In dusty areas or areas with heavy traffic flow, such
as inner city or desert areas, early replacement may be
required. (For scheduled maintenance information, please
refer to the “Owner’s Manual Supplement / Scheduled
Maintenance”.)
(e) Operating tips
 Make sure the air inlet grilles in front of the windshield are
not blocked by leaves or other obstructions.
 If air flow control is not satisfactory, check the dashboard
vents. (See “Center vents”, “Side vents” and “Lower vent”.)\
 To help cool down the interior after parking in the hot sun,
drive for the first few minutes with the windows open. After
the excess heat has blown away, close the windows.
 When driving on dusty roads, close all windows. If dust
thrown up by the vehicle is still drawn into the vehicle after
closing the windows, it is recommended that the air intake
control button be left to the OUTSIDE AIR mode and the fan
speed control button be pressed to anywhere except the
“OFF” button.
 If following another vehicle on a dusty road, or driving in
windy and dusty conditions, it is recommended that the air
intake control button be temporarily pressed in to the
RECIRCULATED AIR mode, which will close off the outside
passage and prevent outside air and dust from entering the
vehicle interior.

AIR CONDITIONING
212
Center vents
20X039d
The center vents may be opened or closed as shown.
Side vents
20X025c
The side vents may be opened or closed as shown.
Lower vent
20X026a
The lower vent may be opened or closed as shown.
For removing frost or fog, it is recommended that you close the
lower vent when you push the windshield air flow button or use
the “Floor” or the “Floor/Windshield” mode.

AUDIO
221
21X553
In the “TAPE” or “CD” mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.
(b) Tone and balance
How good an audio program sounds to you is largely
determined by the mix of the treble, mid −range, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, mid− range,
and bass.
A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.
22X612
Each time you push the “AUDIOTUNE” knob, the display
changes as in the following. To adjust the tone and
balance or turn on or off the automatic sound levelizer,
turn the knob.
BAS: Adjusts low− pitched tones.
MID: Adjusts mid− pitched tones.
TRE: Adjusts high− pitched tones.
FAD: Adjusts the sound balance between the front and rear
speakers.
BAL: Adjusts the sound balance between the right and left
speakers.
ASL: Turns on or off the automatic sound levelizer.
Automatic Sound Levelizer (ASL): When the audio sound
becomes difficult to be heard due to road noise, wind noise,
etc. during driving, the system adjusts to the optimum volume
and tone quality according to the noise level. While the
Automatic Sound Levelizer (ASL) is on, “ASL” appears on the
display.

AUDIO
227
Each time you push the
“
” or “” button, the program type
changes as in the following:
 ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION
 MISC
 ALERT (Emergency message)
Push the “SEEK TRACK” or “SCAN” button with the program
type shown on the display and the radio seeks or scans the
station in the relevant program type.
TRAF (Traffic) function: A station that regularly
broadcasts traffic information is automatically located.
When you push the “TRAF” button, “TRAF SEEK” appears on
the display and the radio will start seeking any traffic program
station.
If no traf fic program station is found, “NO TRAF INFO” appears
on the display for a few seconds and the display returns to the
previous mode. Radio text message:
21x557
If the radio receives a radio text from RDS station, “MSG”
appears on the display. Push the “TEXT” button, and a text
message is displayed.
If the entire the message is not displayed, “
” will appear on
the display. To display the rest of the message, push and hold
the “TEXT” button until you hear a beep.
After the entire message has been displayed, the message will
disappear.
In case a text message is not accepted on the display, you can
push the “TEXT” button and hold it to display the rest of the
message.
When the system can show the station name, “RDS” appears
on the display. Each time you push the “TEXT” button,
indication on the display changes from the band to the station
name, a radio text in this order. After 6 seconds passes,
indication returns to the band.

AUDIO
235
Cassette tape player operation
(a) Playing a cassette tape
21X558b
When you insert a cassette tape, the exposed tape should
face to the right.
The player will automatically start when you insert a cassette
tape. At this time, “TAPE” appears on the display.
To stop or eject the cassette tape, push the “EJECT” button.
Autoreverse feature: After the cassette player reaches the
end of a tape, it automatically reverses and begins to play the
other side, regardless of whether the cassette was playing or
fast forwarding.
20X559
If a cassette is already in the slot, push the “TAPE” button.
Dolby\b Noise Reduction* feature: If you are listening to a
tape that was recorded with Dolby* Noise Reduction, push the
button. The display will indicate that the Dolby noise
reduction system is on.
The Dolby NR mode reduces tape noise by about 10 dB. For
best sound reproduction, play your tapes with the Dolby NR on
or off according to the mode used for recording the tape.
To play a tape recorded without Dolby NR, push the button until
the symbol disappears from the display.
* Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporati on. “DOLBY” and the double−D
symbol
are trademarks of Dolby Laboratories Licensing
Corporation.

STARTING AND DRIVING
260
The shift position is displayed on the instrument
cluster.
P: Parking, engine starting and key removal position
R: Reverse position
N: Neutral position
D: Normal driving position (Shifting into overdrive
possible)
4: Position for engine braking (Shifting into overdrive not
possible)
When the cruise control is being used, even if you
downshift from “D” to “4”, engine braking will not be
enabled because the cruise control is not cancelled. For
the operation to decrease the vehicle speed, see page
278.
3, 2: Position for more powerful engine braking
L: Position for maximum engine braking Correct use of the automatic transmission is explained in
the following parts.
(a) Normal driving
(b) Using engine braking
(c) Using the “3”, “2” and “L” positions
(d) Backing up
(e) Parking
(f) Good driving practice
(g) Driving in “2nd STRT” (second start) mode
(h) If you cannot shift the selector lever

STARTING AND DRIVING
266
(g) Driving in “2nd STRT” (second start)mode
31X012c
In the “2nd STRT” (second start) mode, the transmission
system shifts up from second gear. Use this mode when
starting your vehicle in sand, mud, ice or snow.
To set the “2nd STRT” mode, push the “2nd” switch. In the “2nd
STRT” mode, the “2nd STRT” indicator light comes on. To
cancel the “2nd STRT” mode, push the “2nd” switch again.
The “PWR” mode is automatically cancelled when you push
the “2nd” switch.
(h) If you cannot shift the selector lever
If you cannot shift the selector lever from “P” position even
though the brake pedal is depressed, use the shift lock
override button. For instruct ions, see “If you cannot shift
automatic transmission selector lever” on page 357.
FOURWHEEL DRIVE SYSTEM
(a) Fourwheel drive control
31X013e
Use the fourwheel drive control lever and center
differential lock button to select the fo llowing transfer and
center differential modes.
The “H” and “L” position of the four−wheel drive control lever
provides either lock or unlock mode of the center differential
depending on the center differential lock button position.
Use the center dif ferential lock system if your wheels get stuck
in a ditch, or when you are driving on a slippery or bumpy
surface. When the center differential is locked, the vehicle
stability control system is automatically turned off and the
center dif ferential lock and “VSC OFF” indicator lights come on
because the function that controls engine performance
interferes with the process of freeing your wheels.