fuse LEXUS LX470 2006 Owners Manual

SWITCHES
32
HEADLIGHT DIMMER AND TURNSIGNAL SWITCH
12X002a
For high beam, push the lever forward. Pull it back for low
beam. For the headlight flasher, pull it further back.
A blue light in the instrument cluster indicates high beam or
headlight flasher is on.
The headlight flasher works even when the headlight switch is
off.
12X003a
For signaling turns, move the lever up or down in the
conventional manner.
The ignition key must be in the “ON” position.
The turn signal is self −cancelling after a turn, but after a lane
change, you may have to cancel it by hand. You can also signal
a lane change by moving the turn signal lever partway and
holding it there.
If the green light in the instrument cluster flashes faster than
normal, it indicates that the front or rear turn signal bulb has
burned out. If this indicator light does not come on, the fuse
or the indicator light itself has probably failed.

INTERIOR EQUIPMENT
75
Rear
14X603
The power outlets are designed for power supply for car
accessories.
The ignition key must be in the “ACC” or “ON” position for t\
he
power outlets to be used.
NOTICE
To prevent the fuse from being blown, do not use the
electricity over the total vehicle capacity of 12V/120W
(front and rear outlets together).
 To prevent the battery from being discharged, do not
use the power outlets longer than necessary when
the engine is not running.
Close the power outlet lids when the power outlets
are not in use. Inserting anything other than an
appropriate plug that fits the outlet, or allowing any
liquid to get into the outlet may cause electrical
failure or short circuits.
REAR CONSOLE BOX
14X074
 1
For upper box 2For lower box
To use the rear console box, open as shown in the
illustration.

AIR CONDITIONING
205
(a) Climate control
SETTING OPERATION automatic control
20X019d
1. Push the “AUTO” button.
Air flow quantity, switching of the diffusers, on−off of the air
conditioning, and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are automatically
adjusted. The operation status is shown by each indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the mode relevant to the
depressed button is set. Other conditions continue to be
adjusted automatically.
It is recommended that you close the lower vent. For details
about this, see page 212.
Push the “OFF” button to turn the air conditioning off.
20X020d
2. Turn the “TEMP” knob until the desired temperature is
displayed.
The “TEMP” knob is used to set the desired passenger
compartment temperature. The temperature of air delivered
to the passenger compartment will be controlled automatically
according to the setting. The figures on the panel indicate
degrees Fahrenheit or Centigrade.

AIR CONDITIONING
214
21x611
Warm air
Cool airSETTING OPERATION automatic control
20X055a
1. Push the “AUTO” button.
Air flow quantity and switching of the diffusers are
automatically
adjusted. The operation status is shown by each
indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the operation corresponding to
the button depressed is set. Other conditions continue to be
adjusted automatically.
Push the “OFF” button to turn the rear air conditioning off.

AUDIO
225
(b) Presetting a station
21X555
1. Tune in the desired station.
2. Push
one of the station selector buttons ( 16 ) and hold
it until a beep is heard. This sets the station to the button
and the button number ( 16 ) appears on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse. (c) Selecting a station
Tune in the desired station using one of the following methods.
21X556b
Preset
tuning: Push the button ( 1− 6 ) for the station you want.
The button number ( 1− 6 ) and station frequency appear on the
display.
Manual tuning: Turn the “AUDIO− TUNE” knob. The radio will
step up or down to another frequency.
Seek tuning: Push the “SEEK” button. The radio will begin
seeking up or down for a station of the nearest frequency and
will stop on reception. Each time you push the button, the
stations will be searched automatically one after another.

AUDIO
230(d) Presetting a channel
22x652
1. Tune in the desired channel.
2. Push one of the channel selector buttons ( 16 ) and
hold it until a beep is heard. This sets the channel to the
button and the button number ( 16 ) appears on the
display.
Each button can store three SAT channels. To change the
preset channel to a different one, follow the same procedure.
The preset channel memory is
cancelled when the power
source is interrupted by battery disconnection or a blown fuse. (e) Selecting a channel
Tune in the desired channel using one of the following
methods.
22x653a
Preset tuning: Push the button ( 1−6 ) for the channel you
want. The button number ( 1−
6 ) and channel number appear
on the display.
Manual tuning within the channel category: Turn the
“AUDIO−TUNE” knob. The radio will step up or down the
channel.
Manual tuning within the current channel category: Push
the “SEEK” button. The radio will step up or down the channel
within the current channel category.

IN CASE OF AN EMERGENCY
374STORING/DELETING NUMBERS IN MEMORY
(NAMETAGS)
Your Lexus Link System can store up to 20 phone
numbers. These numbers can be dialed by simply saying
“Call”, then saying the nametag.
Tips for creating nametags:

Short nametags that are similar may be easily confused by
the system. You may get better recognition of your
nametags if you make them longer, for example “George
Washington” (no pause), instead of “George” only.
 The best way to store a nametag is when it is quiet inside
the vehicle. The vehicle should be stationary and the air
conditioning fan turned off.
 When you have finished speaking your phone number, you
do not need to say “Store number” or “Dial” to indicate that
you are done. If you pause and say nothing, the system will
ask you if you want to store or dial. Say “Yes”. To store a nametag:
1. Press the phone button.
You will hear “Lexus Link ready”.
2. Say “Store”.
You will hear “Phone number to store, please”.
3. Say the number you wish to store with no pauses.
Lexus Link will repeat the number, then you will hear “Yes or
No”.
4. Say “Yes” (or “No” to try again).
You will hear “Nametag, please” (or Number not stored).
5. Say “(new nametag)”.
You will hear “About to store (new nametag)” and “Does that
sound OK?”
6. Say “Yes” (or “No” to try again).
You will hear “Storing (new nametag)”.

IN CASE OF AN EMERGENCY
378Voice command error messages:
“Pardon”
The system has not been able to match your command with a
word that it knows. Repeating the command distinctly should
fix the problem. After 3 pardon responses, the system will try
to guess the command you are requesting. If correct, say
“Yes”, if not, say “No” and the system will prompt you with its
next−best guess.
“Slower, please”
Repeat the command after a short pause. This response
normally happens if you say a command before the system is
ready for it or if there is substantial background noise.
General tips for better speech recognition:

Noise may confuse the speech recognition system. You
usually get better performance from the system in quieter
conditions:

The air conditioning/heater fan creates noise. Turn it down
or off for better speech system performance.
 Driving at high speeds creates louder engine noise and
wind noise. You may get better results at lower speeds.
 An open window or an open moon roof results in more noise
in the vehicle. Close all windows for better results.
 Noisy rainstorms can also reduce performance.
 If passengers are talking while you use the speech system,
it may be confused by their speech. You will get better
results if all occupants of the vehicle are quiet while the
system is listening for commands.

Personal calling—the system is only listening for about 5
seconds aft er it prompts you to speak. If the system does not
hear a response, it will prompt you again, or cancel the
transaction. If you begin to speak too soon, it will tell you
“Slower, please”. Try pausing for a half second before
speaking.

61X004m
INTRODUCTION
396
ENGINE COMPARTMENT OVERVIEW
1 Engine oil filler cap
2 Engine oil level
dipstick
3 Brake fluid reservoir
4 Fuse box
5 Battery
6 Washer fluid tank
7 Condenser
8 Radiator
9 Engine coolant
reservoir
10 Power steering fluid
reservoir
11 Suspension fluid
reservoir

INTRODUCTION
399
Checking brake fluid
Parts (if level is low):
FMVSS No. 116 DOT 3 or SAE J1703 brake fluid
Tools:
 Rag or paper towel
 Funnel (only for adding fluid)
Checking power steering fluid
Parts (if level is low):
Automatic transmission fluid DEXRON
II or III
Tools:
 Rag or paper towel
 Funnel (only for adding fluid)
Checking suspension fluid AHC
Parts (if level is low):
Suspension fluid AHC
Tools:
 Rag or paper towel
 Funnel (only for adding fluid)
Checking battery condition
Tools:
Warm water
 Baking soda
 Grease
 Conventional wrench (for terminal clamp bolts)
Checking and replacing the blade type fuses
Parts (if replacement is necessary):
Fuse with same amperage rating as original
Checking the cartridge type fuses
Parts (if replacement is necessary):
Genuine Lexus fuse or equivalent with same amperage
rating as original
Adding washer fluid
Parts:
Water
 Washer fluid containing antifreeze (for winter use)
Tools:
 Funnel