LEXUS NX300h 2022 Owners Manual

The range of each detection area is:A
Approximately 1.6 ft. (0.5 m) to 11.5 ft. (3.5 m) from either side of the vehicle*2
B
Approximately 3.3 ft. (1 m) forward of the rear bumper
C
Approximately 9.8 ft. (3 m) from the rear bumper
D
Approximately 9.8 ft. (3 m) to 197 ft. (60 m) from the rear bumper
*3
TurningtheBlindSpotMonitorsystemON/OFF
The Blind Spot Monitor system can be changed between ON and OFF on the
center display
1 Select
.
2 Select [Driving assist@.
3 Select [Blind spot monitor@.
When the BSM function is disabled, the driving assist infomation indicator illumi- nates.
Each time the power switch is turned off then changed to ON, the Blind Spot
Monitor will be enabled automatically.
INFORMATION

RWhen the sensor is misaligned due to a strong impact to the sensor or its surround-
ing area
R When mud, snow, ice, a sticker, etc., is covering the sensor or surrounding area on
the rear bumper
R When driving on a road surface that is wet with standing water during bad weather,
such as heavy rain, snow, or fog
R When multiple vehicles are approaching with only a small gap between each
vehicle
R When the distance between your vehicle and a following vehicle is short
R When there is a significant difference in speed between your vehicle and the
vehicle that enters the detection area
R When the difference in speed between your vehicle and another vehicle is chang-
ing
R When a vehicle enters a detection area traveling at about the same speed as your
vehicle
R As your vehicle starts from a stop, a vehicle remains in the detection area
R When driving up and down consecutive steep inclines, such as hills, dips in the road,
etc.
R When driving on roads with sharp bends, consecutive curves, or uneven surfaces
R When vehicle lanes are wide, or when driving on the edge of a lane, and the vehicle
in an adjacent lane is far away from your vehicle
R When an accessory (such as a bicycle carrier) is installed to the rear of the vehicle
R When there is a significant difference in height between your vehicle and the
vehicle that enters the detection area
R Immediately after the Blind Spot Monitor is turned on

RWhen the distance between your vehicle and a following vehicle is short
R When an accessory (such as a bicycle carrier) is installed to the rear of the vehicle6-2.Usingthesafedrivingsupportfunctions3916
Driving support system

Supportingsafeexitbydetectingdetectableobjectsattherearofthevehiclebyoutputtingsounds,displayingscreensasawarningorcancellingopeningofthedoors
The Safe exit assist (with door opening control) is a system that uses radar sensors installed on the inner side of the rear bumper to help occupants judge if an
approaching vehicle or bicycle may collide with a door when opening it or cancel
opening of a door, to reduce the possibility of a collision.WARNING

RWhen 3 minutes or more have elapsed since the hybrid system was stopped (the
time which operation is possible may be extended if a door is opened and closed)
R When your vehicle is not completely stopped
Systemcomponents
A
Center display
Turning the safe exit assist on/off. When opening of a door is canceled, the driver is
informed through voice guidance that the system has operated.
B
Multi-information display/Head-up display *
/Buzzer
If collision with a door is likely and opening of the door is canceled, the door will be displayed on the multi-information display and head-up display. Also, if a door is
opened when an outside rear view mirror indicator is illuminated, a buzzer will sound as a warning.
C
Outside rear view mirror indicators
When a vehicle or bicycle which may collide with a door (other than the back door)
when opened is detected, the outside rear view mirror indicator on the detected side will illuminate. If the door on the detected side is open, or opening of the door is
canceled, the outside rear view mirror indicator will blink.
D
Door opener switch (manual release handle)
If a door opener switch is operated to open a door while the outside rear view mirrorindicator on that side is illuminated, opening of the door will be canceled.
INFORMATION

WARNINGRIf the surrounding area of a sensor is scratched or dented, or part of them has
become disconnected.

TurningtheSafeexitassistsystemON/OFF
The Safe exit assist system can be changed between ON and OFF on the center
display
1 Select
.
2 Select [Driving assist@ .
3 Select [Safe exit assist@ .
When the Safe exit assist function is disabled, the driving assist infomation indicator
illuminates.
Each time the power switch is turned off then changed to ON, the Safe exit assist will be enabled automatically.
INFORMATION

RWhen an approaching vehicle or bicycle is traveling along a stationary object, such
a wall or sign
R When the back door is open
R When a bicycle carrier, ramp, or other accessory is installed to the back of the
vehicle
R When a vehicle or bicycle is approaching at high speed
R When towing with the vehicle
R When stopped on a steep slope
R When stopped on a curve or at the exit of a curve6-2.Usingthesafedrivingsupportfunctions398