stop start LEXUS RX330 2006 Owner's Guide

STARTING AND DRIVING
445
1Higher2Lower
3Height control indicator lights
 Changing the mode
You can change the easy access mode to the “LO”, “N” or “HI”\
mode when the engine is running.
To change easy access mode to “LO” mode: Push the
height select switch on the “ ” (higher) side once.
To change easy access mode to “N”mode: Push the height
select switch on the “ ” (higher) side twice.
In the following cases, the vehicle’s height is automatically
changed to “N” (normal) mode.
 The vehicle speed exceeds approximately 12 km/h (8 mph).
 The engine is restarted and the easy access mode is
canceled. To change easy access
mode to “HI” mode: Push the height
select switch on the “ ” (higher) side for three times.
The “LO”, “N” or “HI” indicator light blinks while the\
vehicle’s
height changes. When the vehicle’s height reaches the “LO”,
“N” or “HI” mode, the indicator light remains on.
If the vehicle’s height is changed frequently, the raising or
lowering will take longer than usual. There is no problem in the
electronically modulated air suspension.
CAUTION
If you select easy access mode, check under the vehicle
to make sure nothing that could damage the vehicle or
no one who could be injured is there and that the
underbody of the vehicle does not touch the ground
before the engine is stopped.

STARTING AND DRIVING
446
(e) Turning off the electronically modulated airsuspension
1Height control switch
2Height control “OFF” indicator light
To turn off the electronically modulated air suspension
with the vehicle stopped, push the height control switch.
The height control “OFF” indicator light comes on and the
vehicle height is fixed in the same mode as was last
selected.
This status is maintained in the system even after the engine
is stopped.
If you push the switch again, the height control “OFF” indicator
light goes out and the electronically modulated air suspension
is turned on. When the vehicle’s speed exceeds 30 km/h (19 mph), the
height control “OFF” indicator light goes out and the
electronically modulated air suspension turns on
automatically.
CAUTION

If you drive through water, such as when crossing
shallow streams, first check the depth of the water
and the firmness of the bottom of the river bed then
put the vehicle height into “HI” mode with the height
select switch and turn off the electronically
modulated air suspension by pushing the height
control switch. Drive your vehicle at 30 km/h (19
mph) or slower and avoid deep water.
 When jacking up, installing tire chains or tying your
vehicle with chains or wires for transportation by a
flat bed, be sure to turn off the electronically
modulated air suspension with the height control
switch and stop the engine. Otherwise, the automatic
leveling function may cause the vehicle’s height to
change, resulting in an unexpected accident.
 If your vehicle must be towed, put the vehicle height
in the “N” mode and turn off the electronically
modulated air suspension. Otherwise, the automatic
leveling function may cause the vehicle’s height to
change, resulting in an unexpected accident.

STARTING AND DRIVING
448In the following cases, there is a problem somewhere in the
electronically
modulated air suspension, in which case the “N”
mode is automatically selected. Although there is no problem
to continue driving normally, have the electronically modulated
air suspension checked by your Lexus dealer as soon as
possible.
 The height control “OFF” indicator light does not come on
when the ignition switch is turned on.
 The height control “OFF” indicator light blinks.
(g) Operating noise of the electronically
modulated air suspension
You may hear an operating noise in the following cases. There
is no problem in the electronically modulated air suspension.
Selecting vehicle height with the height select switch
 Adjusting vehicle height according to the number of
occupants or the luggage load
 Changing vehicle height by selecting the easy access mode
when the engine is stopped
 Changing vehicle height by selecting the easy access mode
when the vehicle speed exceeds 12 km/h (8 mph)
 Changing the vehicle height by selecting the “HI” mode
when the vehicle speed exceeds 50 km/h (31 mph) or
driving at a speed of 30 km/h (19 mph) for 10 seconds or
more
 Lowering the vehicle’s height automatically when the
vehicle is moving at high speed
 Returning the vehicle height after high speed driving

STARTING AND DRIVING
449
(h) Parking and stopping tips
If you immediately stop the engine to park the vehicle after
off−road driving, the vehicle height is lowered slightly as the
vehicle becomes cool. When parking, make sure there is
nothing that will be in contact with the underbody of the vehicle.
If the “HI” (high) mode is selected when you start the engine,
the vehicle returns to the “HI” (high) height. If the “LO” (\
low) or
“N” (normal) mode is selected when you start the engine, the
vehicle height is change to “N” (normal) mode.
If you park the vehicle for a long time, the vehicle height may
be gradually lowered. When parking for a long time, make sure
there is nothing that will be in contact with the underbody of the
vehicle. If the “HI” (high) mode is selected when you start the
engine, the vehicle returns to the “HI” (high) height. If the “LO”\
(low) or “N” (normal) mode is selected when you start the
engine, the vehicle height is change to “N” (normal) mode.
If you stop the engine, the vehicle height may change in
accordance with the change in the temperature. When you
start the engine, the vehicle returns to the “HI” (high) height.\
If the “LO” (low) or “N” (normal) mode is selected when \
you
start the engine, the vehicle height is change to “N” (normal)
mode.
TRACTION CONTROL SYSTEM
(twowheel drive models)
The traction control system automatically helps prevent
the spinning of front wheels when the vehicle is started or
accelerated on slippery road surfaces.
When the ignition key is turned to “ON”, the system
automatically turns on.
CAUTION
Under certain slippery road conditions, full traction of
the vehicle and power against front wheels cannot be
maintained, even though the traction control system is
in operation. Do not drive the vehicle under any speed
or maneuvering conditions which may cause the
vehicle to lose traction control. In situations where the
road surface is covered with ice or snow, your vehicle
should be fitted with snow tires or tire chains. Always
drive at an appropriate and cautious speed for the
present road conditions.

STARTING AND DRIVING
458
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub− systems. If either sub− system
should fail, the other will still work. However, the pedal will be
harder to press, and your stopping distance will increase. Also,
the brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a single brake
system. Have your brakes fixed immediately.
Brake booster
The brake booster uses engine vacuum to power −assist the
brakes. If the engine should quit while you are driving, you can
bring the vehicle to a stop with normal pedal pressure. There
is enough reserved vacuum for one or two stops but no more!
CAUTION
 Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up your reserved
vacuum.
 Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard, much harder than normal. And your braking
distance will increase.

STARTING AND DRIVING
459
Antilock brake system
The antilock brake system is designed to help prevent
lockup of the wheels during a sudden braking or braking
on slippery road surfaces. This assists in providing
directional stability and steering performance of the
vehicle under these circumstances.
Effective way to press the ABS brake pedal: When the
anti−lock brake system function is in action, you may feel the
brake pedal pulsating and hear a noise. In this situation, to
let the anti−lock brake system work for you, just hold the
brake pedal down more firmly. Do not pump the brake in a
panic stop. This will result in reduced braking performance.
The anti−lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km/h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces such as
on a manhole cover, a steel plate at a construction site, joints
in a bridge, etc. on a rainy day tends to activate the anti −lock
brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds just after the vehicle begins to
move. This means that the anti −lock brake system is in the
self−check mode, and does not indicate a malfunction. When the antilock brake system is activated, the
following conditions may occur. They do not indicate a
malfunction of the system:

You may hear the anti −lock brake system operating and feel
the brake pedal pulsating and the vibrations of the vehicle
body and steering wheel. You may also hear the motor
sound in the engine compartment even after the vehicle is
stopped.
 At the end of the anti−lock brake system activation, the
brake pedal may move a little forward.
CAUTION
Do not overestimate the antilock brake system:
Although the antilock brake system assists in
providing vehicle control, it is still important to drive
with all due care and maintain a moderate speed and
safe distance from the vehicle in front of you, because
there are limits to the vehicle stability and effectiveness
of steering wheel operation even with the antilock
brake system on.
If tire grip performance exceeds its capability, or if
hydroplaning occurs during high speed driving in the
rain, the antilock brake system does not provide
vehicle control.

STARTING AND DRIVING
460
Antilock brake system is not designed to shorten the
stopping distance: Always drive at a moderate speed
and maintain a safe distance from the vehicle in front of
you. Compared with vehicles without an antilock
brake system, your vehicle may require a longer
stopping distance in the following cases:
Driving on rough, gravel or snowcovered roads.
 Driving with tire chains installed.
 Driving over the steps such as the joints on the road.
 Driving on roads where the road surface is pitted or
has other differences in surface height.
Install all 4 tires of specified size at appropriate
pressure: The antilock brake system detects vehicle
speeds u sing the speed sensors for respective wheels’
turning speeds. The use of tires other than specified
may fail to detect the accurate turning speed resulting
in a longer stopping distance.“ABS” warning light
1U.S.A.2Canada
The light comes on when the ignition key is turned to the “ON”
position. If the anti−lock brake system and the brake assist
system work properly, the light turns off after a few seconds.
Thereafter, if either of the systems malfunctions, the light
comes on again.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti −lock brake system, the brake
assist system, the traction control system and the vehicle
stability control system do not operate, but the brake system
still operates conventionally.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti−lock brake system does not
operate so that the wheels could lock up during a sudden
braking or braking on slippery road surfaces.

STARTING AND DRIVING
461
If either of the following conditions occurs, this indicates
a malfunction somewhere in the components monitored
by the warning light system. Contact your Lexus dealer as
soon as possible to service the vehicle.

The light does not come on when the ignition key is turned
to the “ON” position, or remains on.
 The light comes on while you are driving.
A warning light turning on briefly during operation does not
indicate a problem.
CAUTION
If the “ABS” warning light remains on together with the
brake system warning light, immediately stop your
vehicle at a safe place and contact your Lexus dealer.
In this case, not only the antilock brake system will fail
but also the vehicle will become extremely unstable
during braking.
Drumindisc type parking brake system
Your vehicle has a drum−in−disc type parking brake system.
This type of brake system needs bedding −down of the brake
shoes periodically or whenever the parking brake shoes and/or
drums are replaced.
Have your Lexus dealer perform the bedding −down.

STARTING AND DRIVING
462
Brake assist system
If you slam the brakes on such as in an emergency or
apply the brakes more firmly than usual such as when
descending the hill with the designated number of
occupants in the vehicle, the brake assist system
provides more powerful braking.
If you slam the brakes on or apply the brakes more firmly, more
powerful braking will be applied. At this time, you may hear a
sound in the engine compartment and feel the vibrations of the
brake pedal. This does not indicate a malfunction.
The brake assist system becomes operative after the vehicle
has accelerated to a speed in excess of approximately 10 km/h
(6 mph). It stops operating when the vehicle decelerates to a
speed below approximately 5 km/h (3 mph).
For an explanation of this system’s warning light, see “ABS
warning light” on page 81 or 460.
TIRE PRESSURE WARNING SYSTEM
The tire pressure warning system is designed to provide
warning when tire inflation pressure is critically low while
the vehicle is moving. The low tire pressure warning light
comes on to inform you that such low tire pressure may
hamper driving.
This system is not designed to operate when the vehicle is
stopped. Therefore, check the tire inflation pressure regularly.
The recommended cold tire inflation pressure, tire size and the
vehicle capacity weight are on the tire and loading information
label. (For instructions, see “Checking tire inflation pressure”
on page 570.)
Installed tires should be of the specified size. They should be
of the same size and construction. If tires other than the
specified size are used, or if tires of different sizes or
constructions are mixed, the tire pressure warning system will
not function properly.

STARTING AND DRIVING
464
The tread wear is very different among the installed tires.
 Rapid acceleration/deceleration or sharp turns is continue.
 Towing a trailer.
 The loading is over the limit or imbalanced.
 Initialization was not performed correctly after replacing or
rotating tires or wheels.
 The outside temperature is below 0 C (32F) or above
40 C (104 F).
CAUTION
When the tire pressure warning light comes on, observe
the following instructions:
 Adjust the tire inflation pressure to the specified level
as soon as possible.
 Avoid abrupt steering wheel maneuvering and
braking when the tire pressure warning light comes
on. If the vehicle tires deteriorate, you could lose
control of the steering wheel or the brakes, causing
death or serious injury.
Tire pressure warning system reset switch
The tire pressure warning system need to be initialized in
the following conditions:
When the low tire pressure warning light blinks twice
every second
 After replacing or rotating tires or wheels
When initializing the system, the present tire condition is
stored as a standard.
To initialize the system, perform the following:
1. Park the vehicle at a safe place and apply the parking brake.
Stop the engine.
2. Adjust the pressure of all the installed tires to the specified
level. (See “Tires and wheels” on page 566.)
3. Turn the ignition key to “ON”.