LEXUS RX350 2011 Owners Manual

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log62
132 Months or 110,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis 138 Months or 115,000 Miles
Date: ________ Mileage: ________Date: ________ Mileage: ________

Inspect and adjust all fluid levels
Inspect engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀2

SCHEDULED MAINTENANCE LOG

MAINTENANCE
Scheduled Maintenance Log63
144 Months or 120,000 Miles
R eplace engine oil with 0W-20 oil; replace oil filter
Re-torque nuts and bolts of drive shaft (AWD)
Replace air conditioner filter
Replace brake fluid
Replace engine air filter
Replace Smart Key batter y
R eplace spark plugs (use Denso FK20HR11 plugs
or equivalent) 1
Inspect the following:
___ Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Brake rotor thickness and runout
___Drive belt
___Exhaust pipes and mountings
___Fuel lines and connections, fuel tank band
and fuel tank vapor vent s y stem hoses
If you drive primarily under either of these special operating conditions, perform these
additional items:
Driving off-road, on dirt roads or on dusty roads:
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier or heavy vehicle loading:
R eplace rear differential oil (AWD)
Replace transfer case oil (AWD)
Replace transmission fluid
Tighten nuts and bolts on chassis ___F uel tank cap gasket
___Rack and pinion assembly
___Rear differential oil (AWD)
___Steering linkage and boots
___Transfer case oil (AWD)
___Transmission for signs of leakage R eset maintenance reminder light
Rotate tires
Visually inspect brake pads, caliper s
and rotors
Check installation of driver’s floor mat
Road-test vehicle
1
Requir ed under the terms of the Emission Control Warranty.
Date: ___________________________ Mileage: __________________________
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀3

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log6 4
150 Months or 125,000 Miles 156 Months or 130,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Inspect engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
Date: ________ Mileage: ________Date: ________ Mileage: ________
Inspect and adjust all fluid levels
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀4

SCHEDULED MAINTENANCE LOG

MAINTENANCE
Scheduled Maintenance Log6 5
16 2 Months or 135,000 Miles
Clean air conditioner filter
Inspect and adjust all fluid levels
Re-torque nuts and bolts of drive shaft (AWD)
Replace Smart Key battery
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Inspect the following:
___ Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Drive belt
___Exhaust pipes and mountings
Note: If 0W-20 oil was not used at last oil change, or if you drive primarily under certain special operating
conditions, you should also replace the engine oil with 0W-20 oil and replace the oil filter. See page 44 for
conditions that apply. Some conditions require additional maintenance. See below.
If you drive primarily under either of these special operating conditions, perform these
additional items:
Driving off-road, on dirt roads or on dusty roads:
Inspect engine air filter
Tighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier or heavy vehicle loading:
R eplace rear differential oil (AWD)
Replace transfer case oil (AWD)
Tighten nuts and bolts on chassis ___R ack and pinion assembly
___Rear differential oil (AWD)
___Steering linkage and boots
___Transfer case oil (AWD)
Date: ___________________________ Mileage: __________________________
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀5

SCHEDULED MAINTENANCE LOG
MAINTENANCE
Scheduled Maintenance Log66
168 Months or 140,000 Miles
R eplace engine oil with 0W-20 oil; r eplace
oil filter
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis 17 4 Months or 145,000 Miles
Date: ________ Mileage: ________Date: ________ Mileage: ________

Inspect and adjust all fluid levels
Inspect engine coolant (see page 70)
Reset maintenance reminder light
Rotate tires
Visually inspect brake pads, calipers and rotors
Check installation of driver’s floor mat
Road-test vehicle
Note: If 0W-20 oil was not used at last oil
change, or if you drive primarily under cer tain
special operating conditions, you should also
replace the engine oil with 0W-20 oil and
replace the oil filter. See page 44 for conditions
that apply. Some conditions require additional
maintenance. See below.
If you drive primarily under either
of these special operating conditions,
perform these additional items:
Driving off-road, on dirt roads or on
dusty roads:
Inspect axle shaft boots
Inspect ball joints and dust covers
Inspect engine air filter
Inspect steering linkage and boots
Re-torque nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier
or heavy vehicle loading:
Re-tor que nuts and bolts of drive shaf t
(AWD)
T ighten nuts and bolts on chassis
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀6

SCHEDULED MAINTENANCE LOG

MAINTENANCE
Scheduled Maintenance Log67
180 Months or 150,000 Miles
R eplace engine oil with 0W-20 oil; replace oil filter
Re-torque nuts and bolts of drive shaft (AWD)
Replace air conditioner filter
Replace brake fluid
Replace engine air filter
Replace engine coolant (see page 70)
Replace Smart Key batter y
Inspect the following:
___ Axle shaft boots
___Ball joints and dust covers
___Body
___Brake lines and hoses
___Brake rotor thickness and runout
___Drive belt
___Exhaust pipes and mountings
___Fuel lines and connections, fuel tank band
and fuel tank vapor vent s y stem hoses
If you drive primarily under either of these special operating conditions, perform these
additional items:
Driving off-road, on dirt roads or on dusty roads:
T ighten nuts and bolts on chassis
To wing a trailer, using a car-top carrier or heavy vehicle loading:
R eplace rear differential oil (AWD)
Replace transfer case oil (AWD)
Tighten nuts and bolts on chassis ___F uel tank cap gasket
___Rack and pinion assembly
___Rear differential oil (AWD)
___Steering linkage and boots
___Transfer case oil (AWD)
___Transmission for signs of leakage R eset maintenance reminder light
Rotate tires
Visually inspect brake pads, caliper s
and rotors
Check installation of driver’s floor mat
Road-test vehicle
Date: ___________________________ Mileage: __________________________
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀7

EXPLANATION OF MAINTENANCE ITEMS
MAINTENANCE
Scheduled Maintenance Log68
The following descriptions are provid-
ed to give you a better understanding
of the maintenance services that
should be performed on your vehicle.
The scheduled maintenance log indi-
cates at which time/mileage intervals
each service should be performed.
Please note that many maintenance
services should be performed only
by a qualified technician.
Air Conditioner Filter
Clean or replace at specified inter-
vals. More frequent cleaning or
replacement may be required when
driving in dusty conditions, heavy
traffic areas, urban areas, desert
areas or dirt roads. Refer to your
Owner’s Manualfor service details.
Axle Shaft Boots
Check the axle shaft boots and
clamps for cracks, deterioration and
damage. Replace any damaged parts
and, if necessary, repack the grease.
A qualified technician should perform
these operations.
Ball Joints and Dust Covers
Check the suspension and steering
linkage ball joints for looseness and
damage. Check all dust covers for
deterioration and damage. A qualified
technician should perform these
inspections.
Body Inspection
Visually check for corrosion, scratch-
es and other damage. Check outer
body panels, inner panels of the hood
and doors, and underneath the vehi-
cle. Apply touch-up paint to any chips
and scratches or have them repaired
by a qualified technician.
Brake Fluid
Replace using fluid type specified
in your Owner’s Manual. A qualified
technician should perform this
operation.
Brake Lines and Hoses
Visually inspect for proper installation.
Check for chafing, cracks, deteriora-
tion and signs of leakage. Replace
any deteriorated or damaged parts.
A qualified technician should perform
these operations.
For further information on
maintenance services that you
can perform yourself, see the
maintenance sections of your
Owner’s Manual.
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀8

EXPLANATION OF MAINTENANCE ITEMS

MAINTENANCE
Scheduled Maintenance Log69
Brake Pads, Calipers and Rotors
Check brake pads and rotors for
excessive wear; check brake rotors
for runout. Check brake calipers for
fluid leakage. A qualified technician
should perform these inspections.
Differential Oil
Check for correct oil level and
inspect each differential component
for signs of leakage. If you discover
any leakage, have it repaired immedi-
ately by a qualified technician. Refer
to your Owner’s Manualfor fluid
specifications.
Drive Belt
Inspect for cracks, excessive wear
and oiliness. Check the belt tension
and adjust if necessary. Replace the
belts if they are damaged.
Drive Shaft
Re-torque the flange nuts and bolts.
A qualified technician should perform
this operation.
Driver’s Floor Mat
•Only use the driver’s floor mat
designed specifically for the
model and model year of your
vehicle, such as Lexus Genuine
floor mats.
•Always properly secure the dri-
ver’s floor mat using the retaining
hooks.
•Never install another floor mat
on top of the existing driver’s
floor mat.
•Never install the driver’s floor
mat upside down.
Engine Air Filter
Check for excessive dirt, damage and
oiliness. Replace if necessary.
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀6฀9

EXPLANATION OF MAINTENANCE ITEMS
MAINTENANCE
Scheduled Maintenance Log70
Engine Coolant
When inspecting, visually check
the level of the engine coolant on the
see-through reservoir. Add coolant
as necessary. When replacing, drain
and flush the cooling system and refill
with coolant. Always use Genuine
Toyota Super Long-Life Coolant or
similar high-quality non-silicate,
nonamine, non-nitrate, non-borate
ethylene-glycol coolant with long-life
hybrid organic acid technology (i.e.,
a combination of low phosphates and
organic acids). A qualified technician
should perform these operations.
Check the radiator and condenser
for blockage by leaves, dirt or insects
and clean if necessary. Also check
the hose connections for corrosion
and condition of installation.
Note:Initial replacement of engine
coolant is at 120 months/100,000
miles. Replace every 60 months/
50,000 miles thereafter.
Engine Oil and Oil Filter
Replace the oil filter and drain and
refill the engine oil at specified inter-
vals. SAE 0W-20 oil is the best
choice for good fuel economy and
good starting in cold weather. If SAE
0W-20 is not available, SAE 5W-20
may be used; however, it must be
replaced with SAE 0W-20 at the next
oil change. See your Lexus dealer for
oil specifically formulated for your
vehicle’s engine. For instructions on
how to reset the reminder light, refer
to your Owner’s Manual.
Note:If you do the majority of your
driving under any of the special oper-
ating conditions indicated on page
44, you should replace the engine oil
and oil filter every six months or
5,000 miles, regardless of the oil
used or the certification of the vehicle.
Exhaust Pipes and Mountings
Visually inspect the exhaust pipes,
muffler and hangers for cracks,
deterioration and damage. Start
the engine and listen carefully for
any exhaust leakage. Tighten connec-
tions and replace parts as necessary.
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀7฀0

EXPLANATION OF MAINTENANCE ITEMS

MAINTENANCE
Scheduled Maintenance Log71
Fuel Lines and Connections, Fuel
Tank Band and Fuel Tank Vapor
Vent System Hoses
Visually inspect for corrosion, dam-
age, cracks, and loose or leaking
connections. Tighten connections
and replace parts as necessary.
Fuel Tank Cap Gasket
Visually inspect for cracks, deterio-
ration and damage and replace if
necessary.
Nuts and Bolts on Chassis
Check that tightness of the seat-
mounting bolts and front/rear suspen-
sion-member retaining bolts matches
torque measurements specified in the
Repair Manual.
Rack and Pinion Assembly
Inspect the rack and pinion assembly
for signs of leakage, damage and
loose electrical connections. Tighten
connections and if you discover any
leakage or damage, have it repaired
immediately by a qualified technician.
Road Test
While driving the vehicle, check for
proper operation of engine, transmis-
sion, brakes and steering. Also check
the parking brake, and check for
abnormal noise or vibration from
any part of the vehicle.
Spark Plugs
Replace at specified interval. Install
new plugs of the same type as origi-
nally equipped (see your Owner’s
Manual). A qualified technician should
perform this operation. To ensure
optimum engine performance,
replace only with Denso FK20HR11
plugs or equivalent.
Steering Linkage and Boots
With the vehicle stopped, check for
excessive freeplay in the steering
wheel. Inspect the linkage for bending
and damage and the dust boots for
deterioration, cracks and damage.
Replace any damaged parts. A quali-
fied technician should perform these
operations.
฀8฀9฀5฀7฀7฀_฀2฀0฀1฀1฀฀฀R฀X฀฀฀3฀5฀0฀_฀4฀8฀-฀8฀0฀j฀_฀R฀1฀.฀q฀x฀d฀฀฀฀฀8฀/฀6฀/฀1฀0฀฀฀฀฀7฀:฀5฀2฀฀฀P฀M฀฀฀฀฀P฀a฀g฀e฀฀฀7฀1