headlamp LINCOLN NAVIGATOR 2004 User Guide

1. Make sure the headlamp switch is
in the OFF position.
2. Disconnect the electrical
connector from the foglamp bulb.
3. Rotate the foglamp bulb
counterclockwise and remove from
the foglamp (the rear side of the
foglamp is shown).
4. Install the foglamp bulb in
foglamp by rotating clockwise.
5. Connect the electrical connector
to the new foglamp bulb
Replacing tail lamp bulbs
1. Make sure the headlamp switch is
in the OFF position.
2. Open the liftgate to expose the
lamp assembly screws.
3. Remove the two screws from the
lamp assembly.
4. Carefully pry the lamp assembly
away from the vehicle, by pulling
the assembly directly straight out, to
expose the bulb socket. DO NOT
TIP THE LAMP ASSEMBLY SIDEWAYS.
5. Rotate the bulb socket counterclockwise and remove from lamp
assembly.
6. Pull bulb straight out of socket and push in the new bulb.
7. Install the bulb socket into the lamp assembly and rotate clockwise.
8. Install the lamp assembly on the vehicle and secure with two screws.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Lights
107

Replacing back-up lamp bulbs
The back-up lamp bulbs are located behind the liftgate trim panels.
To change the back-up lamp bulbs:
1. Make sure the headlamp switch is
in the OFF position.
2. Remove the liftgate trim panel by
removing the retaining nuts to
expose the bulb socket.
3. Turn the bulb socket
counterclockwise and pull it out of
the back-up lamp assembly.
4. Pull out the old bulb and replace
it by pushing in a new bulb.
5. Push the connector back into the back-up lamp assembly and turn it
clockwise to secure it in place.
6. Reinstall the liftgate trim panel.
Replacing liftgate tail lamp bulb
1. Make sure the headlamp switch is
in the OFF position.
2. Raise the liftgate and remove the
two retaining nuts on the underside
of the liftgate.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Lights
108

Replacing license plate lamp bulb
The license plate bulbs are located in the license plate housing assembly
on the liftgate. To change the license plate bulbs:
1. Make sure the headlamp switch is
in the OFF position.
2. Remove the license lamp screw
from the assembly.
3. Pull the lamp down and twist the
bulb socket counterclockwise.
Remove the bulb socket from the
lamp.
4. Pull out the old bulb and push in
the new bulb.
5. Install the bulb socket in the lamp assembly by turning it clockwise.
6. Install the lamp assembly and secure it with the retaining screw.
Approach lamp/mirror turn signal bulb removal (if equipped)
To change the bulbs:
1. Make sure the headlamp switch is
in the OFF position and then fold
the mirror forward.
2. Remove the torx screw on the
bottom of the turn signal lens using
a T-10 torx driver.
3. Pull the turn signal lens down to
remove it from the mirror assembly
4. Disconnect the bulb assembly
from the lens.
5. Remove and replace the bulb.
6. Reverse the order to reassemble lamp and lens.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Lights
111

Do not sit on top of a buckled safety belt to avoid the Belt
Minder
chime. Sitting on the safety belt will increase the risk
of injury in an accident. To disable (one-time) or deactivate the Belt
Minder
feature please follow the directions stated below.
One time disable
Any time the safety belt is buckled and then unbuckled during an
ignition ON cycle, BeltMinder
will be disabled for that ignition cycle
only.
Deactivating/activating the BeltMinder  feature
Read step s1-9 thoroughly before proceeding with the
deactivation/activation programming procedure.
The BeltMinder
feature can be deactivated/activated by performing the
following procedure:
Before following the procedure, make sure that:
• The parking brake is set
• The gearshift is in P (Park) (automatic transmission)
• The ignition switch is in the OFF position
• All vehicle doors are closed
• The driver ’ s safety belt is unbuckled
• The parklamps/headlamps are in OFF position (If vehicle is equipped
with Autolamps, this will not affect the procedure.)
To reduce the risk of injury, do not deactivate/activate the
BeltMinder
feature while driving the vehicle.
1. Turn the ignition switch to the RUN (or ON) position. (DO NOT
START THE ENGINE)
2. Wait until the safety belt warning light turns off. (Approximately 1 – 2
minutes)
• Steps 3 – 5 must be completed within 60 seconds or the procedure will
have to be repeated.
3. Buckle then unbuckle the safety belt three times, ending with the
safety belt unbuckled. This can be done before or during BeltMinder

warning activation.
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Seating and Safety Restraints
193

If you smell exhaust fumes inside your vehicle, have your dealer
inspect your vehicle immediately. Do not drive if you smell
exhaust fumes.
Important safety precautions
A computer system controls the engine ’ s idle revolutions per minute
(RPM). When the engine starts, the idle RPM runs higher than normal in
order to warm the engine. If the engine idle speed does not slow down
automatically, have the vehicle checked. Do not allow the vehicle to idle
for more than 10 minutes at the higher engine RPM.
Before starting the vehicle:
1. Make sure all vehicle occupants have buckled their safety belts. For
more information on safety belts and their proper usage, refer to the
Seating and Safety Restraints chapter.
2. Make sure the headlamps and vehicle accessories are off.
3. Make sure the gearshift is in P
(Park).
4. Make sure the parking brake is
set.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Driving
218

Fuse/Relay
Location Fuse Amp
Rating Passenger Compartment Fuse Panel
Description
5 7.5A* Brake On/Off (stoplamp) switch, Powertrain
Control Module (PCM) (keep alive power),
EATC control head, Body Security Module
(BSM) (keep alive power), Speed control
deactivation switch, Speed control servo,
SecuriLock LED, 3rd row seat relay coils,
Power liftgate module, Clock, Brake Shift
Interlock (BSI) solenoid
6 15A* Headlamp switch (parklamps and switch
backlighting feed), Parklamps, License
lamps, Foglamp relay coil, Trailer tow
electric brake controller (illumination), BSM
(autolamp parklamps), Floor console gear
selector lighting, Switch backlighting
module, Foglamp indicator
7 7.5A* Radio (Start signal)
8 10A* Rear window defroster switch, Heated
outside mirrors, Rear window defroster
indicator (climate control head)
9 — Not used
10 20A* Trailer tow back-up lamps relay, Trailer tow
7 – wire connector (back-up lamps), Trailer
tow parklamps relay, Trailer tow 7 – and
4 – wire connectors (parklamps)
11 10A* A/C compressor clutch relay, A/C
compressor clutch solenoid, Air suspension
compressor relay, 4x4 Integrated Wheel
Ends (IWE) solenoid
12 10A* Speed control relay, Speed control servo
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Roadside Emergencies
269

Fuse/Relay
Location Fuse Amp
Rating Passenger Compartment Fuse Panel
Description
33 20A* HEGO sensors, EGR vacuum regulator
(EVR) solenoid, Intake Manifold Tuning
valve (IMTV) solenoid, Canister vent
solenoid, Vapor Management valve (VMV)
solenoid, A/C compressor clutch relay coil
34 20A* PCM, Idle Air Control (IAC) solenoid, Mass
Air Flow (MAF) sensor, Fuel injectors, Fuel
pump relay, Fuel pump shut-off switch, Fuel
pump motor
35 20A* High beam headlamps, Instrument cluster
high beam indicator
36 10A* Trailer tow right turn/stop lamps
37 20A* Cargo area power point
38 25A* Rear wiper motor, Washer pump (rear
window wash)
39 20A* Console power points
40 20A* DRL relays, DRL foglamps, DRL headlamp
relay coil, Headlamp switch (headlamps),
Multifunction switch (flash-to-pass), BSM
(autolamp headlamps relay), High beam
relay coil, Fuse 25 (LH low beam), Fuse 23
(RH low beam)
41 20A* Cigar lighter, OBD II diagnostic connector
42 10A* Trailer tow left turn/stop lamps
101 30A** Starter motor relay, Starter motor solenoid
102 30A** Ignition switch power
103 30A** ABS/AdvanceTrac
module (pump motor)
104 30A** LH 3rd row seat relay, LH 3rd row seat
switch, LH 3rd row seat motor
105 30A** Power liftgate module, Power liftgate
motors, Power running boards control
106 30A** Trailer tow battery charge relay, Trailer tow
7 – wire connector (battery charge)
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Roadside Emergencies
272

Fuse/Relay
Location Fuse Amp
Rating Passenger Compartment Fuse Panel
Description
107 30A** Auxiliary A/C blower relay, Auxiliary A/C
blower motor
108 30A** Passenger seat motor switch, Passenger seat
lumbar switch and motor
109 30A** Driver seat lumbar switch and motor,
Memory module, Power memory mirrors,
Adjustable pedals switch and motor
110 30A** Power running boards
111 50A** Air suspension compressor relay, Air
suspension compressor
112 30A** ABS/AdvanceTrac
module (valves)
113 30A** Front wiper motor, Washer pump
(windshield wash)
114 40A** Rear window defroster relay, Rear window
defroster grid, Heated mirrors (Fuse 8)
115 30A** 4x4 module, Transfer case shift motor
116 40A** Front blower motor relay, Front blower
motor
117 30A** RH 3rd row seat relay, RH 3rd row seat
switch, RH 3rd row seat motor
118 30A** Driver and passenger climate control seat
module
401 30A** Power windows (circuit breaker), Main
window switch, Window motors, Window
switches, Moonroof module
R01 Starter relay Starter motor solenoid
R02 Delayed
accessory
relay Fuse 22, CB 401, Power windows, Moonroof,
Flip windows, Radio, DVD, Navigation radio
amplifier, Navigation antenna amplifier
R03 Hi-beam
relay Fuse 35, Hi-beam headlamps, Hi-beam
indicator
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Roadside Emergencies
273

OPENING THE HOOD
1. Inside the vehicle, pull the hood
release handle located under the
bottom left corner of the instrument
panel.
2. Go to the front of the vehicle and
release the auxiliary latch located
under the front of the hood, just
above the passenger side headlamp.
Slide the yellow handle to release
the auxiliary latch.
3. Lift the hood until the lift
cylinders hold it open.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Maintenance and Specifications
306

LINCOLN ACCESSORIES FOR YOUR VEHICLE
A wide selection of genuine Lincoln accessories are available for your
vehicle through your local authorized Lincoln or Ford of Canada dealer.
These quality accessories have been specifically engineered to fulfill your
automotive needs; they are custom designed to complement the style
and aerodynamic appearance of your vehicle. In addition, each accessory
is made from high quality materials and meets or exceeds Lincoln ’ s
rigorous engineering and safety specifications. Ford Motor Company will
repair or replace any properly dealer-installed Lincoln accessory found to
be defective in factory-supplied materials or workmanship during the
warranty period, as well as any component damaged by the defective
accessory. The accessory will be warranted for whichever provides you
the greatest benefit:
• 12 months or 20,000 km (12,000 miles) (whichever occurs first), or
• the remainder of your new vehicle limited warranty.
This means that genuine Lincoln accessories purchased along with your
new vehicle and installed by the dealer are covered for the full length of
your New Vehicle ’ s Limited Warranty — 3 years or 60,000 km (36,000
miles) (whichever occurs first). Contact your dealer for details and a
copy of the warranty.
Not all accessories are available for all models.
Following is a list of several Lincoln Genuine Accessory products. Not all
accessories are available for all models. To find out what accessories are
available for your vehicle, please contact your dealer or visit our online
store at: www.lincolnaccessories.com.
Exterior style
Bug shields
Deflectors
Front end covers
Headlamps, fog lights and Daytime Running Lamps (DRLS)
Splash guards
Wheels
Interior style
Floor mats
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Accessories
Accessories
359