garage door programming LINCOLN NAVIGATOR 2004 Owners Manual

When programming your HomeLink  Wireless Control System to
a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLink  Wireless Control System with any garage
door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink  at: www.homelink.com or 1 – 800 – 355 – 3515.
Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink  equipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink  buttons be erased for security purposes, refer to
Programming in this section.
Programming
Do not program HomeLink  with the vehicle parked in the garage.
Note: Your vehicle may require the ignition switch to be turned to the
ACC position for programming and/or operation of the HomeLink  .Itis
also recommended that a new battery be placed in the hand-held
transmitter of the device being programmed to HomeLink  for quicker
training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outside
buttons releasing only when the red
light begins to flash after 20
seconds. Do not repeat step one to
program additional hand-held
transmitters to the remaining two
HomeLink  buttons. This will erase
previously programmed hand-held
transmitter signals into HomeLink  .
2. Position the end of your
hand-held transmitter 2 – 8cm(1 – 3 inches) away from the HomeLink 
button you wish to program (located on your visor) while keeping the
red light in view.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Driver Controls
133

3. Simultaneously press and hold
both the HomeLink  and hand-held
transmitter button. Do not release
the buttons until step 4 has been
completed.
Some entry gates and garage door
openers may require you to replace
step 3 with procedures noted in the
“ Gate Operator and Canadian Programming ” section for Canadian
residents.
4. The red light will flash slowly and then rapidly. Release both buttons
when the red light flashes rapidly. (The rapid flashing light indicates
acceptance of the hand-held transmitters ’ radio frequency signals.)
5. Press and hold the just-trained HomeLink  button and observe the red
light. If the light is a constant red, programming is complete and your
device should activate when the HomeLink  button is pressed and
released. Note: To program the remaining two HomeLink  buttons,
begin with step 2 in the “ Programming ” section — do not repeat step 1.
Note: If the red light blinks rapidly for two seconds and then turns to a
continuous red, proceed with steps 6 through 8 to complete
programming of a rolling code equipped device.
6. At the garage door opener receiver (motor-head unit) in the garage,
locate the “ learn ” or “ smart ” button (usually near where the hanging
antenna wire is attached to the unit).
7. Press and release the “ learn ” or “ smart ” button. (The name and color
of the button may vary by manufacturer.)
Note: There are 30 seconds in which to initiate step eight.
8. Return to the vehicle and firmly press, hold for two seconds and
release the HomeLink  button. Repeat the press/hold/release sequence
again, and, depending on the brand of the garage door opener (or other
rolling code equipped device), repeat this sequence a third time to
complete the programming.
HomeLink  should now activate your rolling code equipped device. To
program additional HomeLink  buttons begin with step 2 in the
“ Programming ” section. For questions or comments, please contact
HomeLink at www.homelink.com or 1 – 800 – 355 – 3515.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Driver Controls
134

Gate Operator & Canadian Programming
During programming, your
hand-held transmitter may
automatically stop transmitting —
not allowing enough time for
HomeLink  to accept the signal
from the hand-held transmitter.
After completing steps 1 and 2
outlined in the “ Programming ”
section, replace step 3 with the following:
Note: If programming a garage door opener or gate operator, it is
advised to unplug the device during the “ cycling ” process to prevent
overheating.
• Continue to press and hold the HomeLink  button (note step 3 in the
“ Programming ” section) while you press and release — every two
seconds ( “ cycle ” ) your hand-held transmitter until the frequency
signal has been accepted by the HomeLink  . The red indicator light
will flash slowly and then rapidly after HomeLink  accepts the radio
frequency signal.
• Proceed with step 4 in the “ Programming ” section.
Operating the HomeLink  Wireless Control System
To operate, simply press and release
the appropriate HomeLink  button.
Activation will now occur for the
trained product (garage door, gate
operator, security system, entry
door lock, or home or office lighting
etc.). For convenience, the
hand-held transmitter of the device
may also be used at any time. In the event that there are still
programming difficulties, contact HomeLink  at www.homelink.com or
1 – 800 – 355 – 3515.
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus) Driver Controls
135

HomeLink universal
transceiver (see Garage door
opener) ......................................136
Homelink wireless control
system ........................................132
Hood ..........................................306
I
Ignition ...............................217, 354
Infant seats
(see Safety seats) .....................206
Inspection/maintenance (I/M)
testing ........................................328
Instrument panel
cleaning ...................................302
cluster ........................................10
lighting up panel and
interior .....................................101
J
Jack ............................................275
positioning ...............................275
storage .....................................275
Jump-starting your vehicle ......282
K
Keyless entry system
autolock ...................................162
programming entry code .......164
Keys ...................................166 – 167
positions of the ignition .........217
L
Lamps
autolamp system .......................99 bulb replacement
specifications chart ................103
daytime running light .............100
fog lamps ...................................99
headlamps .................................99
headlamps, flash to pass ........100
instrument panel, dimming ...101
interior lamps .................103 – 104
replacing
bulbs ................103, 105 – 108, 110
Lane change indicator
(see Turn signal) ......................102
Liftgate ......................149, 156 – 157
Lights, warning and indicator ....10
anti-lock brakes (ABS) ..........222
Limited-slip axle .......................227
Load limits .................................252
GAWR ......................................252
GVWR ......................................252
trailer towing ..........................252
Loading instructions .................253
Locks
autolock ...................................162
childproof ................................154
doors ........................................153
Lubricant specifications ...351, 354
Lumbar support, seats .............169
M
Message center .................136 – 137
english/metric button .............143
system check button ..............144
warning messages ...................144
Mirrors ...............................114, 122
automatic dimming rearview
mirror ......................................122
heated ......................................123
programmable memory ..158, 171
2004 Navigator (nav)
Owners Guide (post-2002-fmt)
USA English (fus)Index
364