ECU LUCID AIR 2022 User Guide

From this menu, you can:-Press + ADD NEW HOMELINK to
add a new device. See Programming
HomeLink .
- Press HOMELINK SETTINGS to edit or
remove existing devices. See Renaming
or Deleting a Device .
- Press a device name to activate it.
The
icon next to a device indicates that a
signal has been sent to the door or gate. The
menu automatically collapses 3 seconds after
a signal is sent.
Renaming or Deleting a Program
Note: For your security, it is recommended to
delete all programmed devices upon the sale or lease termination of your vehicle.
Renaming a program 1. On the Pilot Panel, select
>
Connectivity > HomeLink, then
select the device to be renamed.
2. On the device details screen, press the
edit icon.
3. Use the on-screen keyboard to edit the device name, then press SAVE to
confirm, or CANCEL to return to the
previous screen.
Deleting a program 1. On the Pilot Panel, select
>
Connectivity > HomeLink, then
select the device to be removed.
2. On the device details screen, press DELETE.
3. The screen will prompt to confirm
whether you wish to delete the selected
device. Press DELETE ALL to confirm,
or CANCEL to return to the previous
screen.
Deleting all programs 1. On the Pilot Panel, select
>
Connectivity > HomeLink.
2. If two or more devices are connected to your vehicle, the option to DELETE ALL
will be available. Press it to continue.
3. The screen will prompt to confirm
whether you wish to delete all
connected HomeLink

Tow Truck Mode
When loading and unloading the vehicle onto
a flatbed tow truck, put the vehicle in Tow
Truck Mode. This can be done on the Pilot
Panel by navigating to Settings > Vehicle and
toggling Tow Truck Mode.
Tow Truck Mode disables the emergency
parking brake, disables the alarm, and shifts
the vehicle into neutral to allow for transport
on and off the flatbed truck.
Lucid recommends that Tow Truck Mode
remain active until after transportation has been completed.
Pulling the Vehicle onto a Trailer or TransporterCAUTION: Under no circumstances
should the vehicle be towed using
the vehicle recovery eye. Doing so
can cause significant damage to your
vehicle.CAUTION: Incorrect installation of the
recovery eye can cause it to become
detached while pulling the vehicle,
resulting in significant damage.WARNING: If the recovery eye mount
is not accessible and the vehicle
is recovered by attaching to a
frame, suspension, or other means,
the vehicle may sustain damage.
Inspect the vehicle and ensure it is
safe to operate.The Towing provider
MUST document the method of
vehicle recovery, whether using the
recovery eye, attachment to the body,
suspension, or other means.Failure to
do so could result in a hazardous
situation when operating the vehicle.
The recovery eye is available in the trunk of
your vehicle and located on the underside of
the right-hand floor panel.
To install the recovery eye:
1. Release the rubber cover from the attachment point behind the front grille.
2. Position the recovery eye through thebumper and rotate it clockwise into the
attachment point on the body until it
is fully seated. Visually check that the
recovery eye is parallel to the ground to
ensure correct installation.
3. Attach the winch cable to the recovery eye.
4. Place the vehicle in Neutral (N) or support rear wheels on a self-loading
dolly (see manufacturer instructions for use).
5. Pull the vehicle slowly onto the trailer or transporter.
Note: After using the recovery eye, remember
to store it back in the trunk and install the
rubber cover on the attachment point.
Securing the Vehicle for Transportation
When the vehicle is in position on the
transporter or trailer, use chocks and tie-down
straps to secure the wheels.
Roadside Assistance & Emergency Information198

Disclaimers
California Proposition 65
WARNING: Operating, servicing, andmaintaining a passenger vehicle can
expose you to chemicals, including
phthalates, which are known to
the State of California to cause cancer
and birth defects, or other reproductive
harm. To minimize exposure, wear gloves or
wash your hands frequently when servicing
your vehicle. For more information, go to
www.P65Warnings.ca.gov/passenger-vehicle .
California Perchlorate Advisory
WARNING: Certain components of
this vehicle, such as lithium batteries,
may contain perchlorate material.
Special handling may apply for
service or end-of-life disposal. See
www.dtsc.ca.gov .
Vehicle Telematics
Lucid Air is an advanced connected vehicle
equipped with a host of advanced electronic
control units (ECUs), each responsible for
a specific set of features. The features
span domains including controls, safety,
infotainment, chassis, AD/ADAS, telematics, to name a few that contribute to functionality,
performance, safety, and security of the
vehicle.
In the process of its operation, each ECU
monitors a set of sensors and controls a
set of actuators depending on the role of
the ECU. As a result, each ECU generates
and collects data about the operational
state, performance, anomalies, environment
conditions, battery and charging related information, speed, direction, location, etc.
The collected data are transmitted to the
Lucid cloud services infrastructure on an
ongoing basis over cellular wireless and
wireless LAN networks. In addition, a portion of the data may be accessed by the
technicians at the service center and stored
in the Lucid information databases.
Lucid may use the vehicle data stored
in the vehicle, databases in the service
centers, and cloud-based infrastructure to enhance its products and services,
including but not limited to vehicle
maintenance, troubleshooting, timely service
recommendations & reminders, additional
feature recommendations, research and
development, and marketing & business
analysis purposes. Lucid Air has the over-the-
air (OTA) software update capability to keep the vehicle software current and improved.Lucid may use the vehicle data to update
vehicle software improvements OTA to avoid
issues proactively before they occur on the
vehicle.
Please see Lucid