sensor MAZDA 232 1990 Workshop Manual Suplement

I OWGIX-028
1 SMUG IX-027
gMi)GlX-03
GI-i4
2. Check the terminals of waterproof connectors from the con-
nector side, as they cannot be accessed from the wire har-
ness side.
Caution l
Use fine wire to prevent damage to the terminal. l
Do not damage the terminal when inserting the
tester lead.
Terminals
Inspection
Pull lightly on individual wires to check that they are secured
in the terminal.
Replacement of terminals
Use the appropriate tools to remove the terminal as shown.
When installing the terminal, be sure to insert it until it locks
securely.
Insert a thin piece of metal from the terminal side of the con-
nector, and then, with the terminal locking tab pressed down,
pull the terminal out from the connector.
< Male >
Same as the female type,
Sensors, Switches, and Relays
Handle sensors, switches, and relays carefully. Do not drop
them or strike them against other parts.
4 I
i c

A PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
pieziG-
INSPECT and ADJUST, if necessary, the following Items to
specification:
D Glass, exterior bright metal and paint for damage
Cl Wheel tug nuts
9 Trre pressures
LII All weatherstrips for damage or detachment
Z Operation of bonnet release and lock
D Operation of trunk lid, hatch and fuel lid opener
(it equipped)
3 Door operation and alignment
5 Headlight aiming
INSTALL the following parts:
D Wheel caps or rings (if equipped)
D Outside mirror(s)
[ UNDER BONNET-ENGINE OFF )
INSPECT and ADJUST, if necessary, the foIlowIng items to
specification:
Cl Fuel, coolant and hydraulrc lines, fittings, connections and
components for leaks
Cl Engine oil level
0 Power steering fluid level (if equipped)
D Brake master cylinder fluid levels
0 Clutch master cylinder fluid levels (if equipped) q
Windshield washer reservoir fluid level
D Radiator coolant level and specific gravity
Ll Tightness of water hose clamps
I3 Tightness of battery terminals, electrolyte level and specific
gravity
c) Manual transaxle oit level
D Drive belt(s) tension
C; Carburetor linkage (choke control, wide open throttle posi-
tion, etc.) (carburetor model only)
D Accelerator cable and linkage for free movement
D Headlight cleaner and fluid level (if equipped)
BLEED air from fuel line (diesel engine only)
CLEAN the spark plugs (except for diesef engine)
piicis-1
INSTALL the foflowing parts:
C Rubber stopper for inside rear view mirror (if equipped)
c! Fuse for accessories
CHECK the operation of the following items:
Cl Seat controls (sliding and redining) and head rest
ci Seat belts and warnrng system
Z! Ignition swrtch and steering lock
III Power window {if equipped)
0 Door locks including child proof door locks
0 Inhibitor switch
(ATX only)
Z All lights including warning and indicator lights
0 Ignrtron key reminder buyer (if equipped) Cl Horn, wipers and washers (front and rear, if equipped)
D Antenna (if equipped} q
Cigarette lighter and clock (if equipped)
I2 Remote controt outside mirror
(if equipped) q
Heater, defogger and air conditioner at various mode selec-
tions (if equipped)
c3 Sunroof (if equipped)
CHECK
the fotiowing items: q
Presence of spare fuse
c3 Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
Cl Operation and fit of windows
D Pedal height and free ptay of brake and clutch pedal
Cl Parking brake
i UNDER BONNET-ENGtNE RUNNING AT ]
1 OPERATtNG TEMPERATURE
CHECK the following items:
Cl Operation of idle-up system for air conditioner or power steer-
ing (if equipped)
13 Automatic transaxle fluid level
D Initial ignition timing
(except disel engine) q
Idle speed
El Operation of throttle position sensor (EGI engine)
13 Operation of cold start device and glow plug warning light
(diesel engine only)
D Operation of dash pot [EGI engine)
t
ON HOtST 1
CHECK the following items:
U Underside fuel, coolant and hydraulic lines, fittings, connec-
tions and components for leaks q
Tires for cuts or bruises
Cl Steering linkage, suspension, exhaust system and all under-
side hardware for
looseness or damage
1 ROAD TEST 1
CHECK the foliowing items:
II Brake operation
D Clutch operation
0 Steering control
c3 Operation of meters and gauges
0 Squeaks, rattles or unusual noises q
Engine general performance
c3 Emergency Iocking retractors
rAFTER ROAD TEST 1
REMOVE the seat and floor mat protective covers
CHECK for the necessary
owner information materials, tools
and spare tire in vehicle
93EOAX-002
A-2

A SCHEDULED MAINTENANCE SERVICES (Australia)
lumber of months or km, whichever cumes first
P
_ 48 54 60 1 66 72
5
60 67.5 75 90 .--- .-- -
.-m-w --v-w _ _ -_-- - - _ _ - -
_ -- - - --- __-
_-
-- -- (82.5
Exhaust manifold bolts and nuts (except turbo) T 1
I i T 1
1 T
Engine timlrtg belt”’ Replace every 105,000 km
Drwe belts * a
A I 1 I 1 1 I 1
! ’ I I 1 1
Engine oil * ’ Except turbo models 1 RIR\R/RIRIRIR R R,R R R/R
For turbo models R
Replace every 5,000 km or 6 months
r-k:1 c:t+*-* 1 Except turbo models
R 1 R 1 1 R ( ) R ( 1 R ( 1
R 1 f R
-
1 VII IIIIc;I 1 For turbo models I R 1 ReDlace everv IO.000 km or E
Engine coolant (Wrth Reservoir)
Fuel
system
Replace e&y 24 months
For F-i. system
Idle speed (if equipped Idle 1 1 1 I
I speed controf)
Air cleaner element 1
R , I R I R
Fuet filter
I I? R R
~ Fuel lines and hoses
1 I 1 I I 1 I I 1 1
Ignition system
t Initial ignition timing
Spark plugs i I I I -1 I I
I I I I I
f
Evaporative emission control system
Evaporative system
Throttle sensor
Exhaust emission contra! system
[ Dashpot
(Except for ATX) I 1 I
1 1 I 1 1 t 1 1 1 1 1 ! 1 1 I 1
Electrical system
Battery electrolyte level and specific gravity ]
I 1 1 I 1 t I ’ 1 1 I 1 f I ( 1
I 1
Chassis and body
Brake lines, hoses and connections
Brake fluid * a
Parking brake
Disc brakes
1 Power steering fluid and line Ilf &uiDDedl
I 1 1 I I I
I 1 1 III II
I ’
I I
Steering operations and gear housing
I
1 1 I --r--j- 1 I
I
Steerino linkanes. rack auide and tie rod pnds .-- --
----.“.a ..‘-~--, J- -.-- _.- .-- -..-- I I I t I 1 1 I I I I I I I 1
Manual transaxle oil I \\!‘I rl\jl I 1 I R III
1 Transfer Automatic carrier oil or 09 automatic transaxle fluid level
1 1 I 1 111 I 1 I l 1 I 1 I 1[11i t I 1 I 1 I I 1 I
R 1 Iii 1 I
1 Rear axle oil (Differential) 1 t I I I I I I I I
t ’ I r . ’ 1 . I I I I I R I 1
I
I I
i T
1 T T T 1 T [ T I 1 T
Front suspension ball joints
Bolts and nuts on chassis and body
I I I . I ! ,
I 1 I . I 1 ’ I I ’
Drive shaft dust boots
I
I 1 I 1
I 1 1 I
~~
- - ’ C1utcl-1 pedat
Clutch fluid
1
A-4

SCHEDULED MAtNTENANCE SERVICES (Europe) A
Maintenance Number of months or km (miles), whichever comes first
Months” - 6 1 12 18 ‘24 30136 42 48
Maintenance Kilometers 1,000 10,000 20,000 30,000 40,000 50,000 ( 60,000 70,000 80,000
(Miles) (600) (6,000) (12,OOO)~(l8,0~0) (24,000) (3O,UOO))(36,000) (42,000) j48,OOU)
Engine
!nrake and exhaust manifold nuts (80&j
Owe belts *’
Engrne timing belt l 3
Engine oil flurbo)‘4
Engine oil (Non-turbo)“4
Oil filter’4
Cooling system (I ncludrng
coolant level adjustment)
Engine coolant T 1 T T
A 1 1 A A 1 A A
Reptace every 100,000 km
{60,000 miles)
Replace every 5,000 km (3,000 miles) or 6 months
R R 1 R R R R ‘ R R R
R R R R R R R ’ R
I I I I
Replace every 2 years
Fuel system
Idle soeed
I A 1
Air cleaner elemenf*5 I f R E
R
Fuel fitter
R R
fuel 11~s and hoses 1
t 1 I I I I
Ignition system
lrritiai ignition timing
Spark plugs
Spark plugs (Only for Sweden) 1 I I I 1 I I 1 I I 1 I
A 1 A A 1 A
Adjust every 30,000 km {
18,000 mils)
Evaporative emission control system
Throttle sensor
Throttle sensor (Only for
Sweden)
Evaporative system Evaporatwe system Khlv
for Sweden) 1 1 Aj 1 A ( [ A ] 1 A
Adjust every 80,000 km (48,000 miles)
I 1 I [ I 1
I I [ 1 I
lnsoect everv 80.000 km (48.000 miles)
Electrical system
Battery electrolyte level and specific gravity
A 1 A A ’ 1 A ; A *
All Electrical system *’ I I 1 I I I I I I
Headlight alignment A A A I
c I A ,
Chassis and body
clutch Dedal
Clutch fluid
Brake lines, hoses and connectrons
Brake pedal
Brake fluid”’
Parking brake
Power brake unit and hoses
Disc brakes
Power steering fluid
Power steering system and hoses I
I I 1 1 1 I I
I I
I
I I I I 1 1 I
1
1 I I
I I I I t ! I I
I I I R I 1 I R
A A A A
I I I I
I 1 I 1
I 1 I I I I j I ,
I
I 1 I 1
I
93GOAX-708
A-9

REMOVAL Bl
/
/
93G05? -72t
Removal note
P/S oil pump
Caution
l Do not damage the hoses.
I _ Remove the P/S oil pump with the hoses still connected.
2. Position the pump away from the engine and secure it with
wire.
A/C compressor
Caution
l Do not damage the hoses.
1. Remove the AC compressor with the hoses still connected.
2. Position the compressor away from the engine and secure
it with wire.
Step 2
1. Disconnect the harness connectors shown in the figure.
DIFFERENTIAL
DIFFERENTIAL
LUCK SENSOR
OIL PRESSURE SWITCH --- -
GROUND
r, IDLE SPEED CONTROL
NEUTRAL SWITCH
’ SOLENOID VALVE w MTX!
(ECE WITHOUT _--------I
CATALYST) BACK-UP LIGHT SWITCH
\‘C
Y ~55 ATX’
d ---a-- ,-,---1
INHIBITOR SWITCH

91 1NSTALLATION
Step 4
1. Connect the hoses shown in the figure.
Caution
l Position the hose clamp in the original location on the hose, and squeeze it lightly with large
pliers to ensure a good fit.
Step 5
1. Connect the harness connectors shown in the figure.
OIL PRESSURE SWITCH
Df STRlBUTdR
OXYGEN SENSOR
(EXCEPT ECE
WITHOUT CATALYST) lVFFFRFh!TIAI
-.I I -4 m-m. I -r-h LOCK SENSOR DIFFERENTIAL
THRO77LE
/--+I / LOCK MOTOR
AC. .A--
r IDLE SPEED CONTROL
r
dz k
/NEUTRAL SWITCH
“Rou2ydy __
HEAT GAUGE UNIT ’
IDLE-UP
SOLENOID VALVE
IECE WlTl-tOUT
‘CATALYST-)
BACK-UP LIGHT SWITCH INHlBlTdR SWITCH
G3UOBX-837
E3i -20

INSTALLATION Bl
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque
@: 19-25 Nm (I-9-2.6 m-kg, 14-19 Mb)
@: 7.8-11 Nm (80~-110 cm-kg, 69-95 in-lb)
2. Connect the airflow sensor connector.
Resonance chamber
1. lnstail the resonance chamber.
Tightening torque:
7.8-W Nm (SO-11 0 cm-kg, 69-95 in-lb)
Undercover and side cuver
1. install the undercovers and side covers.
Steps after installation
1. If the engine oil was drained, refill with the specified amount and type of engine oil.
2. Fill the radiator with the specified amount and type of engine coolant.
3. Fill the transaxle with the specified amount and type of transaxle oil. (Refer to pages J3-36, K3-134.)
4. Connect the negative battery cable.
5. Start the engine and check the following:
(1) Engine oil, transaxle oil, and engine coolant leakage
(2) Ignition timing and idle speed
(3) Operation of emission control system
6. Perform a road test.
7. Recheck the engine oil and engine coolant levels.
93GOSi-719
al-23

B2 REMOVAL
Step 2
1. Disconnect the harness connectors shown in the fiuure.
ALTERNATOR OIL PRESSURE SWITCH
\. PRESSURE REGULATOR
STARTER
CObjTROL VAVLE
E-SPEED CONTROL
CTOR
KNOCK SENSOR
SWITCH
03 w 08X-80’
Step 3
I. Disconnect the hoses shown in the figure.
-
------a-
93GOB2-720
82-14

B2 INSTALLATION
Step 5
1. Connect the harness connectors shown in the figure.
ALTERNATOR OIL PF;IESSURE SWITCH PRESSURE REGULATOR
STARTER CONTROL VAVLE
GRoYD O-i-l-tE SENSOR
IDLE-SPEED CONTROL
KNOCK SENSOR
OXYGEhENSO$
Step 6
Torque Specifications
03UO8X-33’
7.8-11 N-m
(80-110 cm-kg, 69- .
11 N-m (80--f ’IO cm-kg, 69-95 in-lb)
N-m
cm-kg, 69-95 in-Ib)
37-52 (3.8-5.3, 27
7.8--fl N-m (80 107 (9.6-T 1.9, 69-79)
N-m (m-kg, ft-lb)
03U03X-83

INSTALLATION
93G082-7ti
HERE
/+Ju 7
93GOB2-74!
Caution
l Position the hose clamp in the original location on
the hose, and squeeze it lightly with large pliers to
ensure a good fit.
Accelerator cable
1. Install the accelerator
cable.
Tightening torque
@): 7.8-l 1 N4m (80-l 10 cm-kg, 69-95 in-lb)
2. Adjust the cable deflection by turning nuts @ .
Deflection: I-3mm (U&4--0.12 in)
Battery carrier and battery
1 . Install the battery carrier.
Tightening torque:
7.8-l 1 N4m (80-I IO cm-kg, 69-95 in-lb)
2. Install the battery and the battery cover.
3. Install the battery bracket.
Tightening torque:
2.9-5.9 N.m (30-60 cm-kg, 26-52 in-lb)
4. Connect the positive battery cable.
Air cleaner assembly
1. Install the air cleaner assembly.
Tightening torque:
19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
2. Connect the airflow sensor connector.
3. Connect the hoses shown in the figure.
Strut tower bar
I. Instail the strut tower bar.
Tightening torque:
88-108 Narn (9.0-11 .U m-kg, 65-80 ft-lb)
Undercover and side cover
1. Install the undercovers and side covers.
93GOB2-746
82-33