technical specifications MAZDA 323 1992 Workshop Manual Suplement

TD TECHNICAL DATA
Hem Engine
SP DOHC turbo
Note ) I
1 st and 2nd
Synchronizer ring outer diameter
’ I 67.7 I2.665)
mm [in] 3rd and 4th 67.7 12.665 )
5th and reverse 55.7 t2.192)
Synchronizer key dimension 1st and 2nd @ 19.0 {0.748], 04.3 (0.171, 05.0 10.20)
mm [in] 3rd and 4th @ 17.0 10.669J, 04.3 (0.171, @ 5.0 lO.20)
5th and reverse 0 17.0 10.6691, m4.3
10.171, @I 5.0 fO.201
PROPELLER SHAFT
Item
length
Outer diameter Engineflransaxie Model BP DOHC turbo
G25MX-R (GSMX-R)
Front 834.3 { 32.85 ]
mm fin] Center 584 122.99)
Rear
I 437 { 17.20)
Front 75 (2.95)
mm { in] Center 57 12.24) f
Rear 57 12.241
FRONT AND REAR AXLES
Item Specifications
Front driveshaft

Jomt type Inside Double oftset joint
Outside Bell jotnt
Length of joint (between center of joint) mm { rn t - Right 392 (15.4)
left 306 (0.83 ]
Shaft diameter mm {in] 21.0 to.831
I
Rear driveshaft
Joint type Inside 1
Outside 1
Length of joint (between center of joint) mm [in ] ’ Right
Left
Shaft diameter mm (in)
J&t shatt
Length of joint
Shaft diameter
Front axle
Bearing play axial direction mm [in] 1
Rear axle
Bearing play axial direction mm lin] 1
Rear differential (viscous limited slip differential) Double offset joint
Bell joint
519.5 (20.5 ]
489.5 [f9.3]
21.0 IO.831
357.2 1 t4.11
21 .O (0.83 )
0.050 IO.002 ]
0.050 (0.002 ]
*
Reduction gear
Different ia gear
Oifferential ratro
Number of teeth
Flurd
L Ring gear
Drive .pinion gear
Grade
Viscosity Above -18*C fO*F ]
Below -18*C lOoF)
, Capacity
L fUS qt, Imp c$l Hypoid gear
Straight bevel gear
3.909
43
11
API Service GL-5
SAE 90
SAE 80W
0.65 lQ.69, 0.571 STEERING SI
1 Free olav 8RAKING SY
Brake type
Brake pedat
Height
Free play 1
Reserve travel
Clearance whet
Master cylinde
Master cylinder
Front disc brai
. Tyl?e
Thickness of p&
Thickness of pa

SUSPENSION i
TECHNICAL DATA TD
I
Item
Specifications
Front suspension
Suspension type
strut
Sprrng type
Coil spring
Type Oil 1
Shock absorber
Damping force Extended
1,470 1150, 3N]
N [ kgf, Ibf ] at 0.3 mls
Compressed 1
686 (70, 154)
Stabilizer Type Torsion bar
Oiameter mm {in]
23.0 (0.91 )
Total toe-in mm (in>
2 f 3 (0.08 f 0.12)
degree
0*12’ f 18’
Front wheel Turning angle Inner
38* f 3*
alignment
degree Outer
300 f 30
(* Unladen)
Camber angle degree
-u045’ f 45’
Caster angle degree
2035 f 45’
Kingpin angle
degree 12010’
Rear suspension
Suspension type
I Strut
Spring type
Coil spring
Type Oil
Shock absorber
Damping force Extended
882 (90. 1981
N I kgf, Ibf t at 0.3 mis Compressed
392 140, 88 1
Stabilizer , Type Torsion bar
Diameter mm [in] ?9.? { 0.75 1
Rear wheel
Totat toe-in mm {ini
2 f 3 (0.08 f 0.12)
alignment degree
0°t2’ f 18’
(‘Unladen)
Camber angle degree
-0020’ f 45’
l Fuel tank Ml; radiator coolant and engrne oil at speciffed levels; and spare tire, jack, and tools in designated poations.
Coil Spring Specifications
Item Wire diameter Coil center diameter Free length Coil identification mark coler
mm [in] mm (in) mm (in] number
M” Ae2
Front With sunroof 14.5
IO.57 1 l32.5-158.5 15.22-6.24 ) 271.5 1 IO.69 ] 3.35 Pink
Green
.
WIthout sunroof 14.4 IO.561 1 132.6-158.6 (5.22-6.241 267.0 I IO.51 ] 3.24 Light blue Red
With sunroof 8.8-l 2.5
[ 1 0.34-0.49 128.5-131.2 15.0~5.17) 334 { 13.151 6.19 Cream -
Rear .
I 1 Without sunroof I ff;;y;4”81 I t28.6-13t.j [5.06--5.16) / 335 113.19) 1 6.23 1 Pink 1 - I
l I Main rdentrficatlon mark color: Indicated on second coil from bottom.’ l 2 Auxiliary identification mark color: Indicated on third coil from buttom.
TD-13