temperature MAZDA 626 1987 User Guide

1 C ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
CYLINDER HEAD
Removal
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-031
1. Accelerator cable
2. Air cleaner
3. Brake vacuum pipe
4. Intercooler pipe and hose*
5. Drive belt cover
6. Vacuum pump drive belt
7. Fuel hose
8. Water temperature switch
connector
9. Glow plug connector
10. Water thermo switch con-
nector
11. Heat gauge unit connector
12. Boost air temperature sen-
sor connector*
13. Injection pipes
14. Upper radiator hose
15. Water hose
(thermostat—FIR)
16. Oil level gauge and stay
bolt
17. Oil pipe bolt
18. Timing belt (Refer to page
1C—11)
19. Cylinder head cover
20. Camshaft pulley
21. Rear camshaft pulley
76G01C-032
22. Injection pump pulley
23. Seal plate
24. Water hose and pipe
25. Comprex supercharger
drive belt*
26. Heat insulator*
27. Exhaust manifold stay
28. Front exhaust pipe
29. Cylinder head bolt
30. Cylinder head
31. Cylinder head gasket
32. Comprex supercharger*
33. Exhaust manifold
34. Intake manifold
Note
* marked parts are equipped only for the RF-CX.
1C-16

INSTALLATION 1C
Heater Hose
Connect the heater hoses.
Note
Position the hose clamp in the original loca-
tion on the hose and squeeze the clamp lightly
with large pliers to ensure a good fit.
86U01X-221
Connector Location
Install each harness as shown in the figure.
1. Alternator
2. Boost air temperature sensor (RF-CX)
3. Heat gauge unit
4. Water thermo switch
5. Pick up coil
6. Glow cord
7. Front harness connector and ground
76G01C-222
8. Fuel cut valve
9. Oil pressure switch
10. Starter
11. Water temperature switch
12. Transaxle harness
13. Grounds
1C—95

2 A TROUBLESHOOTING GUIDE
SPECIFICATIONS
Engine model Item . FEDOHC F6, F8, FE SOHC
Lubrication system Force-fed
Oil pump
Type Trochoid gear Crescent gear
Oil pump Regulated pressure kPa (kg/cm2, psi) 490 (5.0, 71) 392 (4.0, 57) Oil pump
Oil pressure kPa (kg/cm2, psi)
1,000 rpm 147-245 (1.5-2.5, 21-36) Oil pump
Oil pressure kPa (kg/cm2, psi) 3,000 rpm 343—441 (3.5-4.5, 50-64) 294-392 (3.0-4.0, 43—57)
Oil filter Type Full-flow, paper element Oil filter Relief pressure differential kPa (kg/cm2, psi) 98 (1.0, 14)
Oil cooler Type Water cooled, 6-layer Water cooled, 4-layer
Oil warning pressure kPa (kg/cm2, psi) 29 (0.3, 4.3)
Oil capacity
Total (dry engine) liters (US qt, Imp qt) 4.3 (4.5, 3.8)
Oil capacity Oil pan liters (US qt, Imp qt) 3.6 (3.8, 3.2) Oil capacity
Oil filter liters (US qt, Imp qt) 0.2 (0.21, 0.18) 0.3 (0.32, 0.26)
Engine oil (API service) SD, SE, or SF
76G02A-003
Recommended SAE Viscosity
Temperature j0pj
-30 -20 -10 0 10 20 30 40 50 I l I I 1 < ! I I Temperature j0pj i i i i I i 1 1
-20 0 20 40 60 80 100 120
Engine oil Engine oil
5W-30 X 30 >
Engine oil Engine oil
5W-20 > < 20W-20 > < 40
Engine oil < 10W-30 > Engine oil
< 10W-40 10W-50
Engine oil Engine oil
< 20W-40 20W-50
Engine oil
Temperature range anticipated before next oil change, °C(°F)
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Engine hard
starting
Improper engine oil
Insufficient engine oil
Replace
Add oil
2A— 5
2A— 5
Excessive oil con-
sumption
Oil working up or working down
Oil leakage
Refer to Section 1
Repair
Oil pressure drop Insufficient oil
Oil leakage
Worn or damaged oil pump gear
Worn plunger (inside oil pump) or weak spring
Clogged oil strainer
Excessive main bearing or connecting rod bearing
clearance
Add oil
Repair
Replace
Replace
Clean
Refer to Section 1
2A- 5
2A-11
2A-11
Warning lamp illu-
minated while en-
gine running
Oil pressure drop
Malfunction of oil pressure switch
Malfunction of electrical system
As described above
Refer to Section 15
Refer to Section 15
76G02A-004
2A—4

OUTLINE 2B
SPECIFICATIONS
Item Engine model RF-CX RF-N

Lubrication system Force-fed
Type Trochoid gear
Oil pump Gear width mm (in) 7 (0.28)
Regulated pressure kPa (kg/cm2,
psi)
510-618 (5.2 -6.3, 74—90)
Oil filter
Type Combined, paper element
Oil filter
Relief pressure differential kP (kg/cm2,
psi)
78-118 (0.8--1.2, 11-17)
Oil cooler Type Water cooled, 10 layer Water coold,
4
layer
Oil filter body
Regulated pressure kPa (kg/cm2,
psi)
402—481
(4.1
-4.9, 58—70)
Oil filter body
Oil cooler relief pressure differential kPa (kg/cm2, psi) 177-216 (1.8 -2.2, 26-31)
Oil warning lamp activation pressure kPa (kg/cm2,
psi)
29 (0.3, 4.3)
Oil capacity
Total (dry engine)
Oil pan
Oil filter
liters (US qt, Imp
qt)

liters (US qt, Imp
qt)

liters (US qt, Imp
qt)

6.1 (6.4, 5.4)
5.0 (5.3, 4.4)
0.5 (0.52, 0.44)
Engine oil type API service CD CC,
CD
76G02B-003
Recommended SAE Viscosity
CC) Temperature
—30 —20 —10 0 10 20 30 40 50 i i i i i i i ii CC) Temperature i i II i i i i —20 0 20 40 60 80 100 120
Engine oil
5W-30 >
Engine oil
< 10W-30 >
< 20W-20 >
< 15W-40 >
Engine oil
<T 30 ><T 40
Engine oil
Temperature range anticipated before next oil change, °C(°F)
76G02B-004
2B-3

3A TROUBLESHOOTING GUIDE i
SPECIFICATIONS
^Engine model
Item ^__
FE-DOHC
FE 8-valve,
F8, F6...except
Middle East
.General
FE 12-valve
FE 8-valve F8, F6...only Middle East General

Cooling system Water cooled, forced circulation
Coolant capacity liters (US qt, Imp qt)
With heater 7.5 (7.9, 6.6) Coolant capacity liters (US qt, Imp qt) Without heater 7.0 (7.4, 6.2)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified seal
Thermostat
Type Wax, 2-stage Wax
Thermostat
Opening temperature °C(°F) Sub
.
83.5-86.5 (182-188) Main: 86.5-89.5 (188-193) 86.5-89.5 (188-193) 80.5-83.5 (177-182) Thermostat
Full-open temperature °C(°F) 100 (212) 95 (203)
Thermostat
Full-open lift
mm
(in) Sub: 1.5 (0.06) min.
Main: 8.0 (0.31) min. 8.5 (0.33) min.
Radiator
Type Corrugated
Radiator Cap valve opening pressure
kPa (kg/cm2, psi) 74-103 (0.75-1.05, 11-15)
Cooling
fan

Capacity
W

MTX 80
Cooling
fan

Capacity
W
ATX 120
Cooling
fan
Number
of
blade 4 Cooling
fan

Outer diameter
of
blade
mm
(in) MTX 320 (12.6)
Cooling
fan

Outer diameter
of
blade
mm
(in)
ATX 340 (13.4)

76G03A-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3A—
5

Coolant leakage Repair
—

Radiator fins clogged Clean 3A—
7

Radiator cap malfunction Replace 3A-
6

Cooling fan malfunction Repair 3A-12 Thermostat malfunction Replace 3 A-11
Water passage clogged Clean 3A—
5

Water
DumD
malfunction ReDair
or
replace 3A-
8
Corrosion
Impurities
in
coolant Replace 3A-
5
76G03A-004
3A—4

THERMOSTAT 3A
69G03B-010
76G03A-008
76G03A-009
THERMOSTAT
REMOVAL
1. Drain the engine coolant.
2. Remove the thermostat cover.
3. Remove the thermostat.
INSPECTION
Check the thermostat. Replace if necessary.
1. Visually check that the valve is airtight.
2. Place the thermostat and a thermometer in water.
3. Gradually heat the water and check the following:
\ Model
Item
FEDOHC
FE 8-valve F8,F6...except
Middle
East General FE 12-valve
FE 8-valve, F8,F6...only Middle East General

Initial opening
tem-
perature

Sub
valve 83.5—86.5°C (182—188°F) Main valve 86.5—89.5°C (188—193°F)
86.5—89.5°C
(188—193°F)
80.5—83.5°C (177—182°F)
Full-open
temperature 100°C (212°F) 95°C (203°F)
Full-open
lift

Sub
valve
1.5
mm
(0.06 in) min.
Main valve
8.0
mm
(0.31 in) min.
8.5
mm
(0.33
in)min.

INSTALLATION
1. Install the thermostat into the cylinder head with
jiggle pin at the top.
2. Install a new gasket with the seal print side facing
the cylinder head.
3. Install the thermostat cover.
Tightening torque:
19—30
N
m (1.9—3.1 m-kg, 14—22 ft-lb)
4. Replenish the coolant.
5. Start the engine and check for leaks.
86U03X-018
3 A-11

TROUBLESHOOTING GUIDE
3B

SPECIFICATIONS

Cooling system Water-cooled, forced circulation
Coolant capacity liters (US
qt,
Imp
qt)

With heater 9.5 (10.0, 8.4) Coolant capacity liters (US
qt,
Imp
qt)

Without heater 9.0 (9.5, 7.9)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified mechanical seal
Thermostat
Type Wax, two stage
Thermostat
Opening temperature °C(°F) Main Sub
Thermostat
Opening temperature °C(°F)
86.5-89.5 (188-193) 78.5—81.5 (173-179) Thermostat
Full-open temperature °C(°F) 100 (212) 100 (212)
Thermostat
Full-open lift
mm (in)
8.0 (0.31) min. 1.5 (0.06) min.
Radiator
Type Corrugated
fin

Radiator Cap valve opening pressure
kPa (kg/cm2,
psi)
74-103 (0.75-1.05, 11—15)
Cooling
fan

Type Electric
Cooling
fan

Capacity
W
120
Cooling
fan
Switching temprature orvopi OFF
- ON ^
91 (196) Cooling
fan

Number
of
blade 4
Cooling
fan

Outer diameter
mm
(in) 340 (13.4)

76G03B-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3B-
4

Coolant leakage Repair
—

Radiator fins clogged Clean 3B—
6

Radiator cap malfunction Replace 3B—
5

Cooling fan malfunction Repair 3B-11 Thermostat malfunction Replace 3B—
9

Water passage clogged Clean 3B—
4

Water pump malfunction ReDair
or
replace 3B—
7

Corrosion
Impurities
in
coolant Replace 3B-
4

76G03B-004
3B—3

THERMOSTAT 3B
THERMOSTAT
REMOVAL
1. Drain the engine coolant.
2. Disconnect the upper radiator hose, and water
thermo switch connector.
3. Remove the thermostat cover.
4. Remove the thermostat.
76G03B-010
76G03B-011
Sub valve Main valve
I
INSPECTION
Check the thermostat. Replace if necessary.
1. Visually check that the valve is airtight.
2. Place the thermostat and a thermometer in water.
3. Gradually heat the water and check the following:
Valve opening temperature
Sub valve : 78.5—81.5°C (173—179°F)
Main valve : 86.5—89.5°C (188—193°F)
Full open lift
Sub valve : 1.5 mm (0.06 in) min. at
100°C (212°F)
Main valve : 8 mm (0.31 in) min. at
100°C (212°F)
Valve closing temperature
Sub valve : 75°C (167°F)
Main valve : 83°C
(181
°F)
69G03B-012
76G03B-012
INSTALLATION
1. Install the thermostat into the thermostat case with
jiggle pin at the top.
2. Install a new gasket with the seal print side facing
the thermostat case.
3. Install the thermostat cover.
Tightening torque:
7—10 N-m (70—100 cm-kg, 61—87 in-lb)
4. Install the upper radiator hose and water thermo
switch connector.
5. Replenish the coolant.
6. Start the engine and check for leaks.
3B-9

3B COOLING FAN
WATER THERMO SWITCH
1. Remove the cooling fan water thermo switch.
Note
Make sure that the ignition switch is OFF. If
not, the fan will operate when the connector
is removed.
76G03B-017
76G03B-018
2. Place the water thermo switch in water.
3. Heat the water gradually, and check for continui-
ty of the switch with an ohmmeter. Replace if
necessary.
Temperature Continuity
Above
91
°C (208°F) No
Below 84°C (183°F) Yes
4. Install the water thermo switch and a new O-ring.
Tightening torque:
6—9 N-m (60—90 cm-kg, 52—78 in-lb)
Caution
Do not use sealing tape.
3B-12

4A
FUEL AND EMISSION
CONTROL SYSTEMS
(CARBURETOR)
OUTLINE 4A— 2
SYSTEM DIAGRAM 4A— 2
VACUUM HOSE ROUTING
DIAGRAM 4A— 5
EMISSION COMPONENTS
LOCATION 4A— 8
COMPONENT DESCRIPTIONS 4A—12
SPECIFICATIONS 4A—15
TROUBLESHOOTING GUIDE 4A—17
PARTS INSPECTION 4A—23
AIR CLEANER ELEMENT 4A—23
ACCELERATOR LINKAGE 4A—23
INTAKE MANIFOLD 4A—23
CHOKE CABLE 4A—23
FUEL SYSTEM 4A—24
TROUBLESHOOTING 4A—25
CARBURETOR 4A—26
FUEL PUMP 4A—35
FUEL TANK 4A—36
SEPARATOR 4A—37
TWO-WAY CHECK VALVE 4A—37
THREE-WAY CHECK VALVE 4A—37
FUEL FILTER 4A—37
IDLE SPEED AND IDLE MIXTURE.. 4A—38
ADJUSTMENT 4A—38
AUTO-RETURN CHOKE SYSTEM... 4A—40
TROUBLESHOOTING 4A—40
PTC HEATER SYSTEM 4A—42
TROUBLESHOOTING 4A—42
DECELERATION CONTROL SYSTEM 4A—45
TROUBLESHOOTING 4A—45
BYPASS AIR CONTROL SYSTEM.. 4A—48
DASH POT 4A—50
ANTI-AFTERBURN VALVE 4A—50
MAIN AIR BLEED CONTROL
SYSTEM 4A—51
SLOW FUEL CUT SYSTEM 4A—53
COAST ENRICHMENT SYSTEM .... 4A—54
COASTING LEANER SYSTEM 4A—56
AIR INJECTION SYSTEM 4A—58
INTAKE AIR TEMPERATURE CONTROL
SYSTEM 4A—60
TROUBLESHOOTING 4A—60
PURGE CONTROL SYSTEM 4A—63
VACUUM SWITCH VALVE 4A—63
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4A—64
TROUBLESHOOTING 4A—65
POSITIVE CRANKCASE VENTILATION
SYSTEM 4A—67
PCV VALVE 4A—67
IDLE-UP CONTROL SYSTEM 4A—68
TROUBLESHOOTING 4A—70
IDLE-UP SOLENOID VALVE 4A—76
EVAPORATIVE EMISSION CONTROL
SYSTEM 4A—78
TROUBLESHOOTING 4A—79
IGNITION TIMING CONTROL
SYSTEM 4A-80
TROUBLESHOOTING 4A—81
CONTROL SYSTEM 4A-83
RELATIONSHIP CHART 4A—84
ENGINE CONTROL UNIT 4A—86
INHIBITOR SWITCH 4A—93
IDLE SWITCH 4A—93
VACUUM SWITCH 4A—94
WATER THERMO SWITCH 4A—95
EXHAUST SYSTEM 4A—96
76G04A-001