Brake MAZDA 626 1987 Repair Manual

4C CONTROL SYSTEM
4. Make sure that the throttle valve is fully closed.
5. Turn the throttle sensor so that the BLUE wire volt-
age indicates within the specified closed range.
6. Tighten the throttle sensor mounting screw.
7. Recheck that the BLUE wire voltage is within the
specified range.
76G04C-195
8. Turn the ignition switch OFF.
9. Disconnect the SST and reconnect the throttle sen-
sor connector.
10. Disconnect the negative battery terminal and de-
press the brake pedal for 5 seconds to eliminate
the from the malfunction memory from the control
unit.
76G04C-196
76G04C-198
4C-106
IDLE SWITCH
Inspection
1. Disconnect the idle switch connector.
2. Check continuity between the switch and a ground.
Throttle valve condition Continuity
Fully closed Yes
Open No
3. If not correct, check condition of the wiring harness
of the idle switch. Replace the idle switch and throt-
tle body as an assembly, if necessary.
WATER THERMO SWITCH
Inspection
1. Remove the switch from the radiator.
2. Place the switch in water with a thermometer and
heat the water gradually.
3. Check for continuity of the switch with an
ohmmeter.
Coolant temp. Continuity
More than approx. 17°C (63°F) Yes
Less than approx. 10°C (63°F) No
4. If not correct, replace the water thermo switch.

ALTERNATOR 5
Warning
Disconnect the nagative battery terminal when disconnect or reconnect B terminal.
TEST 1
1. Disconnect the alternator connector (2-pin).
2. Connect the SST.
4. Connect the red clip of the adapter harness to the battery
(
+
),
and check that the red
lamp and green lamp illuminate.
5. Start the engine and check that both lamps go off.
86U05X-010
TEST 2
1. Connect an ammeter (75A min.) between the wire and the B terminal.
2. Turn all headlights and accessories on, and depress the brake pedal.
3. Start the engine and check that output current is 70A (RF-CX: 75A) or more at
2,500—3,000 rpm of the engine speed.
Caution
Do not ground the B terminal.
76G05X-029
B terminal
5-25

5 ALTERNATOR
TEST 3
1. Turn all electric loads off and release the brake pedal.
2. Check that output current is 5A or more at 2,500—3,000 rpm of the engine speed.
B • , \ B terminal
.w/^y
w
86U05X-013
TEST 4
1. Turn all electric loads off and release the brake pedal.
2. Check that output voltage between S terminal and ground is within specification at
2,500—3,000 rpm of the engin speed.
Voltage: 14.1—14.7V
S terminal
86U05X-072
TEST 5
1. Turn the ignition switch ON.
2. Check that L terminal voltage is within specification.
Voltage: 1—5 V
- L terminal
86U05X-073
5—26

ALTERNATOR 5
TEST 6
1. Turn the ignition switch ON.
2. Turn all electric loads off and release
the brake pedal.
3. Check that voltage between S terminal
and ground is battery voltage.
S terminal
76G05X-057
76G05X-030
86U05X-074
REMOVAL (GASOLINE)
Remove in the sequence shown in the figure.
1. Disconnect the negative battery terminal.
2. Disconnect the wire and connector from the al-
ternator.
3. Remove the bolts.
4. Remove the V-belt.
-5. Remove the alternator to upper side (LHD) or lower
side (RHD).
REMOVAL (DIESEL)
1. Disconnect the negative battery terminal.
2. Remove the right hand driveshaft (Refer to Sec-
tion 9).
3. Disconnect the wire and connector from the al-
ternator.
4. Loosen the idle pulley nuts and remove the drive
belts.
5. Remove the bolts and remove the alternator from
under the vehicle.
76G05X-031
5-27

INSTALLATION 7A
25. Install the grounds to the transaxle case.
Tightening torque:
8—11 N-m (80—115 cm-kg, 69—100 in-lb)
26. Connect the speedometer cable.
76G07A-067
76G07A-068
76G07A-069
76G07A-070
27. Install the intercooler pipe and hose. (RF-CX)
Tightening torque:
19—26 Nm (1.9—2.6 m-kg, 14—19 ft-lb)
28. Install the brake vacuum pipe. (RF-CX)
Tightening torque:
8—11
N
m (80—110 cm-kg, 69—95 in-lb)
29. Connect the brake vacuum hose. (RF-CX)
30. Install the air cleaner assembly and connect the
air flow meter connector.
Tightening torque:
16—27 Nm (1.6—2.8 m-kg, 12—20 ft-lb)
31. Connect the distributor lead.
32. Connect the main fuse block.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
33. Install the battery carrier and battery.
34. Add the correct quantity of the specified transaxle
oil.
Specified
Type
A.T.F.: DEXRON II
Above 0°F:
API: GL-4 or GL-5
SAE 80W-90 or SAE 90
Capacity:
3.35 liters (3.6 US qt, 3.0 Imp qt)
7A-57

7B
AUTOMATIC TRANSAXLE
(Electronically Controlled and 4-Speed)
OUTLINE 7B— 2
SPECIFICATIONS 7B— 2
COMPONENT LOCATION 7B— 3
STRUCTURAL VIEW 7B— 5
OPERATION OF COMPONENTS 7B— 6
FLUID PASSAGE LOCATION 7B— 9
TROUBLESHOOTING (G4A-EL) 7B— 12
GENERAL NOTE 7B— 12
STEP 1
(WARNING CODE RETRIEVAL) 7B— 15
STEP 2
(PRELIMINARY INSPECTION) 7B— 22
STEP 3 (SIGNAL INSPECTION) 7B— 24
STEP 4 (STALL TEST) 7B— 27
STEP 5 (TIME LAG TEST) 7B— 30
STEP 6 (OIL PRESSURE TEST) 7B— 31
STEP 7 (ROAD TEST) 7B— 34
TROUBLESHOOTING (G4A-HL) 7B— 41
GENERAL NOTE 7B— 41
STEP 1
(PRELIMINARY INSPECTION) 7B— 44
STEP 2 (ELECTRICAL
SYSTEM INSPECTION) 7B— 47
STEP 3 (STALL TEST) 7B— 49
STEP 4 (TIME LAG TEST) 7B- 52
STEP 5 (ROAD TEST) 7B— 53
STEP 6 (OIL PRESSURE TEST) 7B— 58
ELECTRICAL SYSTEM
COMPONENTS 7B— 63
MODE SWITCH (G4A-EL) 7B— 63
HOLD SWITCH (G4A-EL) 7B— 63
OD OFF SWITCH (G4A-HL) 7B— 64
INHIBITOR SWITCH 7B- 65
WATER TEMPERATURE SWITCH 7B— 66
FLUID TEMPERATURE SWITCH
(G4A-EL) 7B— 66
BRAKE LIGHT SWITCH
(G4A-EL) 7B— 66
KICK-DOWN SWITCH (G4A-HL) 7B— 67
PULSE GENERATOR (G4A-EL) 7B- 68
VEHICLE SPEED SENSOR
(G4A-EL) 7B— 68
CRUISE CONTROL SWITCH
(CRUISE CONTROL UNIT) 7B— 68
IDLE SWITCH AND THROTTLE
SENSOR (G4A-EL) 7B— 68
OD RELEASE SOLENOID
VALVE (G4A-HL) 7B— 68
SOLENOID VALVES (G4A-EL) 7B— 69
NO LOAD SIGNAL (G4A-EL) 7B— 69
MODE, AND HOLD INDICATOR
LIGHT (G4A-EL) 7B— 69
OD OFF INDICATOR LIGHT
(G4A-HL) 7B— 69
EC-AT CONTROL UNIT
(G4A-EL) 7B— 69
ON-VEHICLE MAINTENANCE 7B— 71
AUTOMATIC TRANSAXLE
FLUID (ATF) 7B— 71
SELECTOR LEVER 7B— 72
THROTTLE CABLE 7B— 73
CONTROL VALVE BODY 7B— 77
OIL STRAINER 7B— 79
ADJUSTMENT OF 2-4 BRAKE
BAND 78— 80
REPLACEMENT OF
DRIVESHAFT OIL SEAL 7B— 80
OIL COOLER 7B— 81
GOVERNOR (G4A-HL) 7B— 82
REMOVAL 7B— 83
PRECAUTION 7B— 83
DISASSEMBLY 7B— 88
DISASSEMBLY-STEP 1 7B— 88
DISASSEMBLY-STEP 2 7B— 94
DISASSEMBLY-STEP 3 7B— 99
DISASSEMBLY-STEP 4 7B—103
INSPECTION AND REPAIR 7B—107
PRECAUTION 7B—107
TORQUE CONVERTER 7B—107
OIL PUMP 7B—108
CLUTCH ASSEMBLY 7B—113
SMALL SUN GEAR AND
ONE-WAY CLUTCH 7B—122
ONE-WAY CLUTCH AND
CARRIER HUB ASSEMBLY 7B-126
3-4 CLUTCH 7B—128
2-3 ACCUMULATOR 7B—132
GOVERNOR ASSEMBLY
(G4A-HL) 7B-133
LOW AND REVERSE BRAKE 7B—134
2-4 BRAKE BAND 7B—135
BAND SERVO 7B—135
OTHER INSPECTION 7B—135
CONTROL VALVE BODY
(G4A-EL) 7B-136
CONTROL VALVE BODY
(G4A-HL) 7B-155
DIFFERENTIAL 7B—177
OUTPUT GEAR 7B—181
IDLE GEAR 7B—182
BEARING COVER ASSEMBLY 7B—185
BEARING HOUSING 7B—186
ASSEMBLY 7B-187
PRECATION 7B—187
ASSEMBLY-STEP 1 7B—187
ASSEMBLY-STEP 2 7B—197
ASSEMBLY-STEP 3 7B—202
ASSEMBLY-STEP 4 7B—208
INSTALLATION 7B—215
TORQUE SPECIFICATIONS 7B—215
HYDRAULIC CIRCUIT (G4A-EL) 7B—221
HYDRAULIC CIRCUIT (G4A-HL) 7B—239
76G07B-001

7B OUTLINE
OUTLINE
SPECIFICATIONS
Model G4A-EL (EC-AT) G4A-HL (4-speed) Model G4A-EL (EC-AT)
FE engine F8 engine

Torque converter stall torque ratio 1.710—1.900
: 1
1.900-2.100
: 1

Gear ratio
First 2.800
Gear ratio
Second 1.540
Gear ratio Third 1.000 Gear ratio
Fourth (OD) 0.700
Gear ratio
Reverse 2.333
Final gear ratio 3.700
Number
of
drive plates/ driven plates
Forward clutch 3/3
Number
of
drive plates/ driven plates
Coasting clutch 2/2
Number
of
drive plates/ driven plates 3-4 clutch 5/5 4/4 Number
of
drive plates/ driven plates
Reverse clutch 2/2
Number
of
drive plates/ driven plates
Low and reverse brake 3/3 4/4
Servo diameter (Piston outer dia./retainer inner dia.) mm (in) 78/53 (3.07/2.09) 78/49 (3.07/1.93) 78/56 (3.07/2.20)
Speedometer gear ratio (Driven/Drive gear) 20
: 25 or
21
: 25

Automatic transmission luid
Type Dexron
n or
MED
Automatic transmission luid Capacity
liters (US qt, Imp
qt)
6.8 (7.2, 6.0)

76G07B-002
7 B—2

OUTLINE 7B
STRUCTUAL VIEW
76G07B-005
1. Coasting clutch 7. Low and reverse brake
2. Forward clutch 8. Output gear
3. Reverse clutch 9. Idle gear
4. Reverse and forward drum 10. Differential
5. 3-4 clutch 11. Parking pawl
6. 2-4 brake band 12. Throttle cable
13. Control body
14. Oil pump
15. Inhibitor switch
16. Pulse generator
17. Fluid temperature switch
7B—5

7B OUTLINE
OPERATION OF COMPONENTS
Low and reverse brake
76U07B-508
Operation Table (G4A-EL)
Range Gear Engine
braking
effect
Operation elements
Range Gear Engine
braking
effect Forward
clutch
Coasting
clutch 3-4
clutch Reverse
clutch
2-4 brake Loftrmm
brake
One-way
clutch 1
One-way clutch 2
Range Gear Engine
braking
effect Forward
clutch
Coasting
clutch 3-4
clutch Reverse
clutch Aoolied Released
Loftrmm
brake
One-way
clutch 1
One-way clutch 2
P — —
R Reverse Yes O O
N -—
D
1st No O O O
D
2nd No o O 0
D 3rd
Below approx.
40 km/h (25 mph)
Yes o O 0 O 0 D 3rd
Above
approx.

40 km/h (25 mph)
Yes 0 o o ® o o
D
OD Yes © o o
S
1st No o 0 o
S
2nd No o 0 0
S
3rd

Below
approx,
40 km/h (25 mph)
Yes 0 0 0 0 o S
3rd Above approx.

40 km/h (25 mph)
Yes o o o ® o o
L 1st No o O o o L 2nd Yes 0 0 o o

HOLD

D
2nd No o o o

HOLD

D 3rd

Below
approx.

40 km/h (25
mpti) Yes o o o 0 o

HOLD

D 3rd Above approx,
40 km/h (25 mph)
Yes o 0 o ® 0 o

HOLD
S
2nd Yes o o 0 o

HOLD
S 3rd
Below approx.
40 km/h (25 mph)
Yes 0 o o 0 o
HOLD
S 3rd Above approx.

40 km/h (25 mph)
Yes o o o ® 0 o

HOLD

L 1st Yes o o o o o

HOLD

L 2nd Yes o 0 0 o
®: Indicates fluid pressure to servo but band not applied due to pressure difference in servo. 76G07B-006 © : Indicates that it does not function to transmition power.
7B-6

OUTLINE 7B
Operation Table (G4A-HL)
Range Gear
Operation elements
Range Gear Engine braking effect
Forward
clutch
Coasting
clutch
3-4 clutch Reverse clutch
2-4 brake Low & One-way
clutch 1
One-way
clutch 2
Range Gear Engine braking effect
Forward
clutch
Coasting
clutch
3-4 clutch Reverse clutch Applied Released reverse brake
One-way
clutch 1
One-way
clutch 2

P
— —

R
—
Yes O 0
N
— —

D
1st No O O O
D 2nd No
o
O
o
D 3rd Yes
o
O 0
®
0
o
D
OD Yes
© O 0

2 2nd Yes
o o o o

1 1st Yes
o o o o o
1 2nd Yes
o o o o
76G07B-007
® : Indicates fluid pressure to servo but band not applied due to pressure difference in servo.
® : Indicates that it does not function to transmit power.
POWER FLOW DIAGRAM
Neutral
1st gear
7B-7