warning MAZDA MODEL 2 2017 Owners Manual (in English)

4–142
When Driving
i-ACTIVSENSE
Changing the Set Vehicle Speed
Changing the set vehicle speed using the
SET switch
Press the SET
switch to accelerate.
Press the SET
switch to decelerate.
The set vehicle speed changes as follows
each time the SET switch is pressed.

European
models Except
European
models
Short press 1 km/h (1 mph) 5 km/h (5 mph)
Long press 10 km/h (5 mph)

NOTE
For example, the set vehicle speed is
changed by pressing the SET switch
four times as follows:
(European models)
The vehicle speed accelerates or
decelerates by 4 km/h (4 mph).
(Except European models)
The vehicle speed accelerates or
decelerates by 20 km/h (20 mph).
To accelerate using the accelerator
pedal
Depress the accelerator pedal and press
and release the SET
or SET switch at
the desired speed. If a switch cannot be
operated, the system returns to the set
speed when you release your foot from the
accelerator pedal.
CAUTION
The warnings and brake control do not
operate while the accelerator pedal is
depressed.
NOTE
  When accelerating using the SET
switch while in headway control, the
set vehicle speed can be adjusted but
acceleration is not possible. If there
is no longer a vehicle ahead,
acceleration continues until reaching
the set vehicle speed. Check the set
vehicle speed by viewing the set
vehicle speed display in the active
driving display.
  When depressing the accelerator
pedal, the inter-vehicle distance
display in the active driving display
changes to the white-line display.
  The minimum settable speed is
30 km/h (19 mph). If the set vehicle
speed reaches 30 km/h (19 mph)
using the switch operation, constant
speed travel is maintained at about
30 km/h (19 mph) even if the SET

switch is pressed. The Mazda Radar
Cruise Control (MRCC) system is
not cancelled.
To Deactivate
The Mazda Radar Cruise Control (MRCC)
is deactivated when the OFF/CAN switch
is pressed twice.

4–14 5
When Driving
i-ACTIVSENSE
Cruise Control Function
While this function is operating, the
headway control operation is cancelled
and only the cruise control function
operates.
The vehicle speed can be set more than
about 25 km/h (16 mph).
Use the cruise control function on
expressways and other highways which do
not require a lot of repeated acceleration
and deceleration.
WARNING
Do not use the cruise control function
in the following locations:
Otherwise, it could lead to an accident.
 
 Roads with sharp curves and where
vehicle traf¿ c is heavy and there is
insuf¿ cient space between vehicles.
(Driving under these conditions
using the cruise control function is
not possible)
  Steep down slopes (Set speed may be
exceeded because suf¿ cient engine
braking cannot be applied)
  Slippery roads such as ice or snow-
bound roads (Tyres could spin
causing you to lose vehicle control)

Always drive carefully:
The warnings and brake control
will not operate after the headway
control function is cancelled and the
system is switched to only the cruise
control function. Depress the brake
pedal to decelerate according to the
surrounding conditions while keeping
a safer distance from the vehicle ahead
and always driving carefully.
Switching to cruise control function
When the MODE switch is pressed while
the Mazda Radar Cruise Control (MRCC)
system is turned on, the system switches to
the cruise control function.
When the system switches to the cruise
control function, the cruise main indication
(white) is displayed in the instrument
cluster and the active driving display to
notify the driver as follows:
 


 The Mazda Radar Cruise Control
(MRCC) set indication (green) or the
Mazda Radar Cruise Control (MRCC)
main indication (white) is turned off,
and the cruise main indication (white) is
turned on.

WARNING
Always turn off the cruise control
function when it is not in use:
Leaving the cruise control function
turned on when it is not in use
is dangerous as it could operate
unexpectedly, resulting in an accident.
How to set the speed
Adjust the system to the desired vehicle
speed using the accelerator pedal.
When the SET
or SET switch is
pressed, the cruise set indication (green) is
turned on and headway control begins.

4–14 8
When Driving
i-ACTIVSENSE
*Some models.
Adjustable Speed Limiter *
The adjustable speed limiter is a function to prevent the vehicle from being driven at a
vehicle speed faster than a set speed. The vehicle speed is controlled to kept it below the set
speed even if the accelerator pedal is depressed.
The adjustable speed limiter can be set between 30 km/h (20 mph) and 200 km/h (125 mph).
The vehicle speed may exceed the set speed when the vehicle is driven on a down slope,
however, the system noti¿ es the driver by À ashing the display and operating a warning
sound.
WARNING
Always turn off the system when changing drivers:
If the driver is changed and the new driver is unaware of the adjustable speed limiter
function, the vehicle may not accelerate when the driver depresses the accelerator
pedal, leading to an accident.
The system consists of the adjustable speed limiter display and the speed limiter switch on
the steering wheel.


Cruise control systemMazda Radar Cruise Control (MRCC) Active Driving Display Display in the instrument cluster
MODE switch
RES/+ switch
SET- switch
OFF/CAN switchCANCEL switch RES switch
OFF switch MODE
switch
SET- switch SET+ switch

4–151
When Driving
i-ACTIVSENSE
Speed Limiter Warning Beep
Indicated in instrument cluster
If the vehicle speed exceeds the set speed by about 3 km/h (2 mph) or more, a warning
sound operates continuously and the adjustable speed limiter display À ashes at the same
time. The warning sound operates and the display À ashes until the vehicle speed decreases
to the set speed or less.
Indicated in active driving display
If the vehicle speed exceeds the set speed by about 3 km/h (2 mph) or more, a warning
sound is activated continuously and the adjustable speed limiter display À ashes at the same
time. The indication stops À ashing and remains on if the vehicle speed continues to exceed
the set speed by about 3 km/h (2 mph) or more, and the indication and warning sound
remain on until the vehicle is driven at the set speed or less.
Verify the safety of the surrounding area and adjust the vehicle speed by applying the
brakes. Additionally, keep a safer distance from the vehicles behind you.


Active Driving Display Display in the instrument cluster

CAUTION
(With cruise control)
If the set speed is set lower than the current vehicle speed by pressing the SET
or RES /
switch, the warning beep is not activated for about 30 seconds even if the vehicle speed is
faster than the newly set speed by 3 km/h (2 mph). Be careful not to drive over the set
speed.
(With Mazda Radar Cruise Control (MRCC))
If the set speed is set lower than the current vehicle speed by pressing the SET
or RES
switch, the warning beep is not activated for about 30 seconds even if the vehicle speed is
faster than the newly set speed by 3 km/h (2 mph). Be careful not to drive over the set
speed.

4–152
When Driving
i-ACTIVSENSE
NOTE
When the system is temporarily cancelled by depressing the accelerator pedal fully, the
adjustable speed limiter display shows the cancel display. If the vehicle speed exceeds the
set speed by about 3 km/h (2 mph) or more while the cancel display is displayed, the set
speed display À ashes but the warning sound is not operated.
Activation/Deactivation
NOTE
When the ignition is switched off, the system status before it was turned off is maintained.
For example, if the ignition is switched off while the adjustable speed limiter is operating,
the system will be operable when the ignition is switched ON the next time.
Activation
Press the MODE switch to operate the system. The adjustable speed limiter screen is
displayed, and the adjustable speed limiter main indication (white) turns on.
NOTE
When the cruise control or Mazda Radar Cruise Control (MRCC) system becomes
operable after pressing the MODE switch, press the mode switch again to switch to the
adjustable speed limiter.
Deactivation
To deactivate the system, do the following operations:
When a cruising speed has been set (adjustable speed limiter set indication (white)/
indicator light (green) turns on)
Long-press the OFF/CAN switch or press the OFF/CAN switch 2 times. The adjustable
speed limiter screen is no longer displayed and the adjustable speed limiter set indication
(white)/indicator light (green) turns off.
When a cruising speed has not been set (adjustable speed limiter main indication
(white) turns on)
Press the OFF/CAN switch. The adjustable speed limiter screen is no longer displayed and
the adjustable speed limiter main indication (white) turns off.

4–153
When Driving
i-ACTIVSENSE
NOTE
When the MODE switch is pressed while the adjustable speed limiter is operating, the
system switches to the cruise control or Mazda Radar Cruise Control (MRCC) system.
Setting the System
WARNING
Always verify the safety of the surrounding area when setting the adjustable speed
limiter:
If the speed is set lower than the current vehicle speed, the vehicle speed is decreased
to the set speed. Verify the safety of the surrounding area and keep a safer distance
between vehicles ahead and behind you.
1. Press the MODE switch to turn the system on.
2. (With cruise control)
Press the SET
to set the speed. When the current vehicle speed is 30 km/h (20 mph) or
more, the speed is set to the current vehicle speed. When the current vehicle speed is less
than 30 km/h (20 mph), the speed is set to 30 km/h (20 mph).
(With Mazda Radar Cruise Control (MRCC))
Press the SET
or SET to set the speed. When the current vehicle speed is 30 km/h
(20 mph) or more, the speed is set to the current vehicle speed. When the current vehicle
speed is less than 30 km/h (20 mph), the speed is set to 30 km/h (20 mph).
3. (With cruise control)
To increase the set speed, press the RES
switch continuously. The set speed can be
adjusted in 10 km/h (5 mph) increments. The set speed can also be adjusted in about
1 km/h (1 mph) increments by pressing the RES
switch momentary. For example, the
set speed increases about 4 km/h (4 mph) by pressing the RES
switch 4 times.
(With Mazda Radar Cruise Control (MRCC))
To increase the set speed, press the SET
switch continuously. The set speed can be
adjusted in 10 km/h (5 mph) increments. The set speed can also be adjusted in about
1 km/h (1 mph) increments by pressing the SET
switch momentary. For example, the
set speed increases about 4 km/h (4 mph) by pressing the SET
switch 4 times.
4. To decrease the set speed, press the SET
switch continuously. The set speed can be
adjusted in 10 km/h (5 mph) decrements. The set speed can also be adjusted in about
1 km/h (1 mph) increments by pressing the SET
switch momentary. For example, the
set speed decreases about 4 km/h (4 mph) by pressing the SET
switch 4 times.

4–156
When Driving
i-ACTIVSENSE
WARNING
Do not rely on the Smart City Brake Support System (SCBS) as a substitute for safer
driving:
The Smart City Brake Support (SCBS) system cannot compensate for unsafe and
reckless driving, excessive speed, tailgating (following another vehicle too closely), and
driving on slippery roads such as wet, snowy, and icy roads (reduced tyre friction and
road contact because of water on the road surface). You can still have an accident.

Do not rely completely on the Smart City Brake Support (SCBS) system:  
 The Smart City Brake Support (SCBS) system is only designed to reduce damage in
the event of a collision. Over reliance on the system leading to the accelerator pedal
or brake pedal being mistakenly operated could result in an accident.
  The Smart City Brake Support (SCBS) is a system which operates in response to a
vehicle ahead. The system may not be able to detect or react to two-wheeled vehicles
or pedestrians.
  The laser sensor for the Smart City Brake Support (SCBS) system is installed near
the rearview mirror. To assure the correct operation of the Smart City Brake Support
(SCBS), heed the following cautions.
 

 
 Do not apply stickers to the surface of the windscreen near the laser sensor
(including transparent stickers). Otherwise, the laser sensor may not be able to
detect vehicles ahead which could result in an accident.
 

 
 Do not apply coating agent to the windscreen. Otherwise, the laser sensor may
not be able to detect vehicles or obstructions in front which could result in an
accident.
 

 
 Do not disassemble the laser sensor.


 
 If cracks or damage caused by À ying gravel or debris is visible near the laser
sensor, stop using the Smart City Brake Support (SCBS) system immediately and
have your vehicle inspected by an expert repairer, we recommend an Authorised
Mazda Repairer. If the vehicle continues to be driven with cracks or scratch marks
left on the windscreen near the laser sensor, the system may operate unnecessarily
and cause an unexpected accident.
  Refer to Stopping The Smart City Brake Support (SCBS) System Operation on
page 4-160 .
 

 
 When replacing the windscreen wipers or windscreen, consult an expert repairer,
we recommend an Authorised Mazda Repairer.

Do not modify the suspension:
If the vehicle height or inclination is changed, the system will not be able to correctly
detect vehicles ahead. This will result in the Smart City Brake Support (SCBS) system
not operating normally or mistakenly operating, which could cause a serious accident.

4–157
When Driving
i-ACTIVSENSE
WARNING
Turn off the Smart City Brake Support (SCBS) when the vehicle is running on a chassis
roller or being towed:
Turn off the Smart City Brake Support (SCBS) system to prevent mistaken operation
when the vehicle is running on a chassis roller or being towed.
Refer to the Stopping the Smart City Brake Support (SCBS) System Operation on page
4-160 on how to turn off the Smart City Brake Support (SCBS) system.
CAUTION
  When driving off-road in areas where there is grass or forage, it is recommended that
the Smart City Brake Support (SCBS) system be turned off.
  Always use tyres for all wheels that are of the speci¿ ed size, and the same
manufacturer, brand, and tread pattern. In addition, do not use tyres with signi¿ cantly
different wear patterns on the same vehicle as the Smart City Brake Support (SCBS)
system may not operate normally.
  The laser sensor includes a function for detecting a soiled windscreen and informing
the driver, however, depending on the conditions, it may not detect plastic shopping
bags, ice or snow on the windscreen. In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive
carefully and pay attention to the road ahead.

4–158
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) system will not operate if the driver is
deliberately performing driving operations (accelerator pedal and steering wheel).
  The Smart City Brake Support (SCBS) system will operate under the following
conditions.
 


 The engine is running.



 The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



 The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



 The Smart City Brake Support (SCBS) system is not turned off.



 The DSC is not malfunctioning. 

 The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam reÀ ected off the reÀ ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
 


 ReÀ ection of the laser is poor due to the shape of the vehicle ahead.



 The vehicle ahead is signi¿ cantly dirty.



 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 The windscreen is dirty.



 The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
pro¿ le.




 Vehicles with certain shapes such as a vehicle carrier. 

 Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat.



 If there is the possibility of partial contact with a vehicle ahead.



 When driving on continuously curving roads, and entering and exiting exits.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor.
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.



 When driving with tyres having signi¿ cantly different wear.

4–159
When Driving
i-ACTIVSENSE
*Some models.
NOTE
  In the following cases, the laser sensor may inadvertently determine that there is a
vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


 Objects on the road at the entrance to a curve.



 Vehicles passing in the opposite lane while making a curve.



 Metal objects, bumps, or protruding objects on the road.



 When passing through a toll gate equipped with a bar.



 When passing under a vinyl curtain or À ag.



 Plastic objects such as pylons.



 Two-wheeled vehicles, pedestrians, animals or standing trees. 

 (Manual transaxle)  If the vehicle is stopped by the SCBS operation and the clutch pedal is not depressed,
the engine stops.
  When the system operates, the user is noti¿ ed by the À ashing Smart City Brake
Support (SCBS) indicator light (red) and the active driving display * .   The Smart City Brake Support (SCBS) warning light (amber) turns on when the
system has a malfunction.
 Refer to Warning Lights on page 4-38 .