MAZDA MODEL 2 2019 Owners Manual (in English)

Page 641 of 759

&$87,21
¾Before pulling out the compressor
plug from the electrical socket, make
sure the compressor power switch is
off.
¾The compressor turns on and off with
the push-button switch.
 7XUQWKHFRPSUHVVRUVZLWFKRQDQG
LQIODWHWKHW\UHFDUHIXOO\WRWKHFRUUHFW
LQIODWLRQSUHVVXUH
:$ 5 1 , 1 *
Never operate the compressor above
300 kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi):
Operating the compressor above 300
kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi) is
dangerous. When the inflation pressure
rises above 300 kPa (3.1 kgf/cm
2, 3 bar,
43.5 psi), heated air will be exhausted
from the back of the compressor and
you could be burned.
NOTE
xCheck the tyre inflation pressure
label (driver's door frame) for the
correct tyre inflation pressure.
xDo not use the compressor for
longer than 10 minutes because
using the compressor for long
periods could damage it.
xIf the tyre does not inflate, repair of
the tyre may not be possible. If the
tyre does not reach the correct
inflation pressure within a 10-minute
period, it probably has received
more extensive damage.
When this happens, the emergency
flat tyre repair kit cannot be used to
repair the tyre. Contact an expert
repairer (we recommend an
Authorised Mazda Repairer).
xIf the tyre has been over-inflated,
loosen the screw cap on the
compressor and bleed some of the
air out.
 :KHQWKHW\UHKDVEHHQLQIODWHGWRWKH
SURSHULQIODWLRQSUHVVXUHWXUQWKH
FRPSUHVVRUVZLWFKRIIDQGUHPRYHWKH
FRPSUHVVRUKRVHIURPWKHW\UHYDOYH
 ,QVWDOOWKHW\UHYDOYHFDS
 3XWWKHHPHUJHQF\IODWW\UHUHSDLUNLWLQ
WKHOXJJDJHFRPSDUWPHQWERRWDQG
FRQWLQXHGULYLQJ
&$87,21
¾Drive carefully to an expert repairer
(we recommend an Authorised
Mazda Repairer) and keep the vehicle
speed below 80 km/h (50 mph).
¾If the vehicle is driven 80 km/h (50
mph) or higher, the vehicle might
begin to vibrate.
NOTE
(With tyre pressure monitoring
system)
If the tyre is not properly inflated, the
tyre pressure monitoring system
warning light will illuminate.
 $IWHUGULYLQJWKHYHKLFOHIRU
PLQXWHVRUNP PLOHV FKHFNWKH
W\UHSUHVVXUHZLWKWKHW\UHSUHVVXUH
JDXJHHTXLSSHGZLWKWKHFRPSUHVVRU,I
WKHW\UHSUHVVXUHKDVIDOOHQEHORZWKH
FRUUHFWW\UHSUHVVXUHLQIODWHWKHW\UHWR
WKHFRUUHFWSUHVVXUHDJDLQIROORZLQJ
WKHVWHSVIURPQXPEHU
,I7URXEOH$ULVHV
)ODW7\UH


Page 642 of 759

&$87,21
¾If the tyre
inflation pressure falls
below 130 kPa (1.3 kgf/cm
2 or bar,
18.9 psi), repair cannot be done with
the repair kit. Park the vehicle on a
level surface
off the right-of-way and
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
¾If the tyre inflation pressure continues
to remain low after repeating steps
15 to 21, park the vehicle on a level
surface off the right-of-way and
contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
NOTE
When checking the tyre inflation
pressure with the tyre pressure gauge
on the compressor unit, make sure the
compressor switch is turned off.
 ,IWKHW\UHLQIODWLRQSUHVVXUHUHPDLQV
VWDEOHWKHW\UHUHSDLULVFRPSOHWH
'ULYHWKHYHKLFOHZLWKFDUHWRDQ
H[SHUWUHSDLUHU ZHUHFRPPHQGDQ
$XWKRULVHG0D]GD5HSDLUHU WRKDYH
WKHW\UHUHSODFHG
&$87,21
¾A tyre that has been temporarily
repaired with the tyre sealant cannot
be reused. Mazda recommends
replacing the tyre with a new one.
¾The wheel can be reused after any
sealant adhering to it is wiped off
and carefully inspected. However,
replace the tyre valve with a new one.
▼,QVSHFWLQJWKH(PHUJHQF\)ODW7\UH
5HSDLU.LW
,QVSHFWWKHHPHUJHQF\IODWW\UHUHSDLUNLWDW
UHJXODULQWHUYDOV
x&KHFNWKHW\UHVHDODQWSHULRGRI
HIIHFWLYHXVH
x&KHFNWKHRSHUDWLRQRIWKHW\UH
FRPSUHVVRU
NOTE
The tyre sealant has a period of effective
use. Check the period of effective use
indicated on the bottle label and do not
use it if it has expired. Have the tyre
sealant replaced at an expert repairer (we
recommend an Authorised Mazda
Repairer) before the period of effective use
has expired.
,I7URXEOH$ULVHV
)ODW7\UH


Page 643 of 759

&KDQJLQJD)ODW7\UH
:LWK6SDUH7\UH
NOTE
If the following occurs while driving, it
could indicate a flat tyre.
xSteering becomes difficult.
xThe vehicle begins to vibrate
excessively.
xThe vehicle pulls in one direction.
,I\RXKDYHDIODWW\UHGULYHVORZO\WRD
OHYHOVSRWWKDWLVZHOORIIWKHURDGDQGRXW
RIWKHZD\RIWUDIILFWRFKDQJHWKHW\UH
6WRSSLQJLQWUDIILFRURQWKHVKRXOGHURID
EXV\URDGLVGDQJHURXV
:$ 5 1 , 1 *
Be sure to follow the directions for
changing a tyre:
Changing a tyre is dangerous if not done
properly. The vehicle can slip
off the jack
and seriously injure someone.
No person should place any portion of their
body under a vehicle that is supported by a
jack.
Never allow anyone inside a vehicle
supported by a jack:
Allowing someone to remain in a vehicle
supported by a jack is dangerous. The
occupant could cause the vehicle to fall
resulting in serious injury.
NOTE
Make sure the jack is well lubricated
before using it.
 3DUNRQDKDUGOHYHOVXUIDFHRIIWKH
ULJKWRIZD\DQGILUPO\VHWWKHSDUNLQJ
EUDNH
 3XWDYHKLFOHZLWKDQDXWRPDWLF
WUDQVD[OHLQ3DUN 3 DPDQXDO
WUDQVD[OHLQ5HYHUVH 5 RUDQGWXUQ
RIIWKHHQJLQH
 7XUQRQWKHKD]DUGZDUQLQJIODVKHU
 +DYHHYHU\RQHJHWRXWRIWKHYHKLFOH
DQGDZD\IURPWKHYHKLFOHDQGWUDIILF
 5HPRYHWKHMDFNWRRODQGVSDUHW\UH
SDJH 
 %ORFNWKHZKHHOGLDJRQDOO\RSSRVLWH
WKHIODWW\UH:KHQEORFNLQJDZKHHO
SODFHDW\UHEORFNERWKLQIURQWDQG
EHKLQGWKHW\UH
NOTE
When blocking a tyre, use rocks or
wood blocks of sufficient size if
possible to hold the tyre in place.
,I7URXEOH$ULVHV
)ODW7\UH


Page 644 of 759

▼5HPRYLQJD)ODW7\UH
:$ 5 1 , 1 *
When jacking-up a vehicle, always shift the
shift lever to 1st or R position (manual
transaxle vehicle) or shift the selector lever
to P position (automatic transaxle vehicle),
apply the parking brake, and place wheel
blocks in the position diagonally opposed
to the jack:
Changing a
flat tyre without using wheel
blocks is dangerous because the vehicle
may move and fall off the jack even with
the shift lever in 1st or R position, or the
selector lever is in P position, which could
result in an accident.
 ,I\RXUYHKLFOHLVHTXLSSHGZLWKD
ZKHHOFRYHUSU\RIIWKHZKHHOFRYHU
ZLWKWKHEHYHOOHGHQGRIWKHMDFNOHYHU

NOTE
Force the end of the jack lever firmly
between wheel and cover, or removal
will be difficult.
&$87,21
Align the notch on the wheel cover with
the valve stem when installing it.

Tyre valve Notch
Damage could occur during
installation if the wheel cover is not
properly aligned.
 /RRVHQWKHZKHHOQXWVE\WXUQLQJWKHP
DQWLFORFNZLVHRQHWXUQHDFKEXWGRQRW
UHPRYHDQ\ZKHHOQXWVXQWLOWKHW\UH
KDVEHHQUDLVHGRIIWKHJURXQG

 3ODFHWKHMDFNRQWKHJURXQG
,I7URXEOH$ULVHV
)ODW7\UH


Page 645 of 759

 7XUQWKHMDFNVFUHZLQWKHGLUHFWLRQ
VKRZQLQWKHILJXUHDQGDGMXVWWKHMDFN
KHDGVRWKDWLWLVFORVHWRWKHMDFNXS
SRVLWLRQ

Jack head
 3ODFHWKHMDFNXQGHUWKHMDFNXS
SRVLWLRQFORVHVWWRWKHW\UHEHLQJ
FKDQJHGZLWKWKHMDFNKHDGVTXDUHO\
XQGHUWKHMDFNXSSRLQW

Jacking position
 &RQWLQXHUDLVLQJWKHMDFNKHDG
JUDGXDOO\E\URWDWLQJWKHVFUHZZLWK
\RXUKDQGXQWLOWKHMDFNKHDGLV
LQVHUWHGLQWRWKHMDFNXSSRVLWLRQ

Tyre blocks
Jacking position
:$ 5 1 , 1 *
Use only the front and rear jacking
positions recommended in this manual:
Attempting to jack the vehicle in
positions other than those
recommended in this manual is
dangerous. The vehicle could slip off
the jack and seriously injure or even kill
someone. Use only the front and rear
jacking positions recommended in this
manual.
Do not jack up the vehicle in a position
other than the designated jack-up
position or place any objects on or
under the jack:
Jacking up the vehicle in a position
other than the designated jack-up
position or placing objects on or under
the jack is dangerous as it could deform
the vehicle body or the vehicle could fall
off the jack resulting in an accident.
,I7URXEOH$ULVHV
)ODW7\UH


Page 646 of 759

Use only the jack provided with your
Mazda:
Using a jack that is not designed for
your Mazda is dangerous. The vehicle
could slip off the jack and seriously
injure someone.
Never place objects under the jack:
Jacking the vehicle with an object
under the jack is dangerous. The jack
could slip and someone could be
seriously injured by the jack or the
falling vehicle.
NOTE
When raising the jack head into the
jacking position and aligning the
groove in the jack head with the rail
under the vehicle body, the top of the
jack head contacts the vehicle's
underbody without the rail contacting
the bottom of the groove.
 ,QVHUWWKHMDFNOHYHUDQGDWWDFKWKH
ZKHHOEUDFHWRW\UHMDFN

 7XUQWKHMDFNKDQGOHFORFNZLVHDQG
UDLVHWKHYHKLFOHKLJKHQRXJKVRWKDW
WKHVSDUHW\UHFDQEHLQVWDOOHG%HIRUH
UHPRYLQJWKHZKHHOQXWVPDNHVXUH
\RXU0D]GDLVILUPO\LQSRVLWLRQDQG
WKDWLWFDQQRWVOLSRUPRYH

:$51,1*
Do not jack up the vehicle higher than
is necessary:
Jacking up the vehicle higher than is
necessary is dangerous as it could
destabilize the vehicle resulting in an
accident.
Do not start the engine or shake the
vehicle while it is jacked up:
Starting the engine or shaking the
vehicle while it is jacked up is
dangerous as it could cause the vehicle
to fall off the jack resulting in an
accident.
Never go under the vehicle while it is
jacked up:
Going under the vehicle while it is
jacked up is dangerous as it could result
in death or serious injury if the vehicle
were to fall off the jack.
,I7URXEOH$ULVHV
)ODW7\UH


Page 647 of 759

 5HPRYHWKHZKHHOQXWVE\WXUQLQJ
WKHPDQWLFORFNZLVHWKHQUHPRYHWKH
ZKHHODQGFHQWUHFDS
▼0RXQWLQJWKH6SDUH7\UH
 5HPRYHGLUWDQGJULPHIURPWKH
PRXQWLQJVXUIDFHVRIWKHZKHHODQG
KXELQFOXGLQJWKHKXEEROWVZLWKD
FORWK

:$ 5 1 , 1 *
Make sure the mounting surfaces of the
wheel, hub and wheel nuts are clean
before changing or replacing tyres:
When changing or replacing a tyre, not
removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The wheel
nuts could loosen while driving and
cause the tyre to come off, resulting in
an accident.
 0RXQWWKHVSDUHW\UH
 ,QVWDOOWKHZKHHOQXWVZLWKWKHEHYHOOHG
HGJHLQZDUGWLJKWHQWKHPE\KDQG

:$ 5 1 , 1 *
Do not apply oil or grease to wheel nuts
and bolts and do not tighten the wheel
nuts beyond the recommended
tightening torque:
Applying oil or grease to wheel nuts
and bolts is dangerous. The wheel nuts
could loosen while driving and cause
the tyre to come off, resulting in an
accident. In addition, wheel nuts and
bolts could be damaged if tightened
more than necessary.
 7XUQWKHZKHHOEUDFHDQWLFORFNZLVH
DQGORZHUWKHYHKLFOH
,I7URXEOH$ULVHV
)ODW7\UH


Page 648 of 759

 8VHWKHZKHHOEUDFHWRWLJKWHQWKHQXWV
LQWKHRUGHUVKRZQ

,I\RXDUHXQVXUHRIKRZWLJKWWKHQXWV
VKRXOGEHKDYHWKHPLQVSHFWHGDWDQ
H[SHUWUHSDLUHU ZHUHFRPPHQGDQ
$XWKRULVHG0D]GD5HSDLUHU 
1XWWLJKWHQLQJWRUTXH
1P NJIPIWOEI 

Page 649 of 759

-XPS6WDUWLQJ
-XPSVWDUWLQJLVGDQJHURXVLIGRQHLQFRUUHFWO\6RIROORZWKHSURFHGXUHFDUHIXOO\,I\RXIHHO
XQVXUHDERXWMXPSVWDUWLQJZHVWURQJO\UHFRPPHQGWKDW\RXKDYHDFRPSHWHQWVHUYLFH
WHFKQLFLDQGRWKHZRUN
:$ 5 1 , 1 *
Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions carefully
before using the battery or inspecting it.
Keep flames and sparks away from open battery cells and do not allow metal tools to
contact the positive (
) or negative () terminal of the battery when working near a battery.
Do not allow the positive (
) terminal to contact the vehicle body:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced during
normal battery operation, could ignite and cause the battery to explode. An exploding battery
can cause serious burns and injuries. Keep all flames including cigarettes and sparks away
from open battery cells.
Keep all flames and sparks away from open battery cells because hydrogen gas is
produced from open battery cells while charging the battery or adding battery
fluid:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced during
normal battery operation, could ignite and cause the battery to explode. An exploding battery
can cause serious burns and injuries. Keep all flames including cigarettes and sparks away
from open battery cells.
Do not jump-start a frozen battery or one with a low fluid level:
Jump-starting a frozen battery or one with a low fluid level is dangerous. It may rupture or
explode, causing serious injury.
Connect the negative lead to a good ground point away from the battery:
Connecting the end of the second jumper lead to the negative (
) terminal of the discharged
battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
,I7URXEOH$ULVHV
%DWWHU\5XQV2XW


Page 650 of 759

Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous. The lead
could get caught when the engine starts and cause serious injury.
&$87,21
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and other
electrical parts beyond repair with a 24 V power supply (two 12 V batteries in series or a 24 V
motor generator set).
 0RYHWKHERRVWHUYHKLFOHVRWKDWLWVEDWWHU\LVDVFORVHDVSRVVLEOHWR\RXUYHKLFOH
V
EDWWHU\
 0DNHVXUHWKDWWKHSRZHUVXFKDVIRUWKHKHDGOLJKWVDQGDLUFRQGLWLRQHULVWXUQHGRII
 5HPRYHWKHEDWWHU\FRYHU
 7XUQRIIWKHERRVWHUYHKLFOH
VHQJLQHDQGFRQQHFWWKHMXPSHUOHDGVLQWKHIROORZLQJ
RUGHU
0DNHVXUHWKDWWKHMXPSHUOHDGVDUHVHFXUHO\FRQQHFWHGVRWKDWWKH\GRQRWGLVFRQQHFW
GXHWRHQJLQHYLEUDWLRQV
VWOHDG
3RVLWLYH  WHUPLQDORQWKHGLVFKDUJHGEDWWHU\
3RVLWLYH  WHUPLQDORQERRVWHUYHKLFOH
VEDWWHU\
QGOHDG
1HJDWLYH  WHUPLQDORQERRVWHUYHKLFOH
VEDWWHU\
,I7URXEOH$ULVHV
%DWWHU\5XQV2XW


Page:   < prev 1-10 ... 601-610 611-620 621-630 631-640 641-650 651-660 661-670 671-680 681-690 ... 760 next >