key MAZDA MODEL 3 5-DOOR 2014 Owner's Guide

4–5
When Driving
Start/Stop Engine
CAUTION
If the KEY warning light (red)
illuminates, or the push button
start indicator light (amber) fl ashes,
this could indicate a problem with
the engine starting system and the
inability to start the engine or switch
the ignition to ACC or ON. Have your
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
NOTE
 y Under the following conditions, the
KEY warning light (red) fl ashes after
the push button start is pressed to
inform the driver that the push button
start will not switch to ACC even if it is
pressed from off.
 y The key battery is dead. y The key is out of operational range. y The key is placed in areas where it is
diffi cult for the system to detect the
signal (page 3-7 ).
 y A key from another manufacturer
similar to the key is in the
operational range.
 y(Forced engine starting method) If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine starts.
Other procedures necessary for starting
the engine such as having the key in the
cabin, and depressing the clutch pedal
(manual transaxle) or the brake pedal
(automatic transaxle) are required.
 y When the engine is force-started,
the KEY warning light (red) remains
illuminated and the push button
start indicator light (amber) remains
fl ashing.
 y(Automatic transaxle) When the selector lever is in the neutral
(N) position, the KEY indicator light
(green) and the push button start
indicator light (green) do not illuminate.
7. Press the push button start after both the KEY indicator light (green) in the
instrument cluster and the push button
start indicator light (green) illuminate.
NOTE
 y After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
 y After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.
8. After starting the engine, let it idle for about ten seconds.
NOTE
 y Whether the engine is cold or warm, it
should be started without the use of the
accelerator.
 y If the engine does not start the fi rst
time, refer to Starting a Flooded Engine
under Emergency Starting. If the engine
still does not start, have your vehicle
inspected by an Authorized Mazda
Dealer (page 7-18 ).
.B[EB@%$&""@&EJUJPOJOEC







4–6
When Driving
Start/Stop Engine
Engine Start Function When Key Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not
to allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.


4–7
When Driving
Start/Stop Engine
NOTE
 y The engine cannot be started unless the
clutch pedal is fully depressed (manual
transaxle) or the brake pedal is fully
depressed (automatic transaxle).
 y If there is a malfunction with the push
button start function, the push button
start indicator light (amber) fl ashes.
In this case, the engine may start,
however, have the vehicle checked at an
Authorized Mazda Dealer as soon as
possible.
 y If the push button start indicator light
(green) does not illuminate, perform the
operation from the beginning again. If
it does not illuminate, have the vehicle
checked at an Authorized Mazda Dealer.
 y To switch the ignition position without
starting the engine, perform the
following operations after the push
button start indicator light (green) turns
on. 1. Release the clutch pedal (manual transaxle) or brake pedal (automatic
transaxle).
2. Press the push button start to switch the ignition position. The ignition
switches in the order of ACC, ON,
and off each time the push button
start is pressed. To switch the
ignition position again, perform the
operation from the beginning.

Emergency Operation for Starting the Engine
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) fl ashes, this could indicate that
the engine may not start using the usual
starting method. Have your vehicle
inspected at an Authorized Mazda Dealer
as soon as possible. If this occurs, the
engine can be force-started. Press and hold
the push button start until the engine starts.
Other procedures necessary for starting the
engine such as having the key in the cabin,
and depressing the clutch pedal (manual
transaxle) or the brake pedal (automatic
transaxle) are required.
.B[EB@%$&""@&EJUJPOJOEC







4–8
When Driving
Start/Stop Engine
Turning the Engine Off
WARNING
Do not stop the engine while the vehicle
is moving: Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking, which
could cause an accident and serious
injury.
1. Stop the vehicle completely.
2. (Manual transaxle)
Shift into neutral and set the parking brake.
(Automatic transaxle)
Shift the selector lever to the P position and set the parking brake.
3. Press the push button start to turn off the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure
the push button start is off .
NOTE
 y The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
 y When the push button start is pressed
from ON to ACC or OFF, the KEY
indicator light (green) may fl ash for
approximately 30 seconds indicating
that the remaining battery power of the
key is low.
 Replace with a new battery before the key becomes unusable.
 Refer to Battery Replacement on page 6-38 .
 y(Automatic transaxle) If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.
Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
.B[EB@%$&""@&EJUJPOJOEC







*Some models.4–18
When Driving
Instrument Cluster and Display
Signal Warning Lights Page
Low Washer Fluid Level Warning Light 7-24
* Tire Pressure Monitoring System Warning Light *1 7-24
(Red) KEY Warning Light
7-24
*1 The light turns on when the ignition is switched on for an operation che\
ck, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains tur\
ned on, have the vehicle inspected at an
Authorized Mazda Dealer.
*2 The light turns on continuously when the parking brake is applied.
.B[EB@%$&""@&EJUJPOJOEC







*Some models.4–19
When Driving
Instrument Cluster and Display
Indicator Lights
These lights turn on or fl ash to notify the user of the system operation status or a system
malfunction.
Signal Indicator Lights Page
* BSM OFF Indicator Light 4-71
(Green) KEY Indicator Light
3-9
Wrench Indicator Light *1 4-20
TCS/DSC Indicator Light *1 4-51 ,
4-52
DSC OFF Indicator Light *1 4-53
(Blue) Low Engine Coolant Temperature Indicator Light
4-20
* Shift Position Indication 4-25
Headlight High-Beam Indicator Light 4-36 ,
4-36
Turn Signal/Hazard Warning Indicator Lights 4-38 ,
4-45
Security Indicator Light *1 3-42
(Amber)
* Cruise Main Indicator Light 4-58
(Green)
* Cruise Set Indicator Light 4-58
.B[EB@%$&""@&EJUJPOJOEC







5–53
Interior Features
Audio System
Settings
NOTE
Depending on the grade and specifi cation, the screen display may differ.
Select the
icon on the home screen and display the Settings screen.
Switch the tab and select the setting item you want to change.
You can customize settings in the setup display as follows:
Tab Item Function
Display Refer to Volume/Display/Sound Controls on page 5-40 .
Safety Blind Spot Monitoring Volume Refer to Blind Spot Monitoring (BSM) System
on page 4-65 .
Sound Refer to Volume/Display/Sound Controls on page 5-40 .
Vehicle Rain Sensing Wiper
Door Lock
Other Refer to Windshield Wipers on page 4-39 .
Refer to Auto Lock/Unlock Function on page
3-16 .
Refer to Transmitter on page 3-4 .
Refer to Locking, Unlocking with Request
Switch (With the advanced keyless function)
on page 3-12 .
Refer to Turn and Lane-Change Signals on
page 4-38 .
Refer to Illuminated Entry System on page
5-131 .
Refer to Lights-On Reminder on page 7-34 .
Refer to Headlights on page 4-33 .
Refer to Daytime Running Lights on page
4-37 .
Devices Bluetooth
Refer to Bluetooth
® Preparation (Type B) on
page 5-89 .
Network Management Wi-Fi™ is used to obtain Navi POI/Real Time
Traffi c function (Such as gas prices, weather,
nearest restaurant)
.B[EB@%$&""@&EJUJPOJOEC







5–101
Interior Features
Bluetooth®
5. Select the icon.
Deleting from your favorites
1. Select the
icon on the home screen
and display the Communication screen.
2. Select the
icon to display the
favorites list.
3. Select the
icon.
4. Select the
icon.
5. Select the contact information which you would like to delete.
6. Select the
icon.
Changing the display order of your
favorites list
1. Select the
icon on the home screen
and display the Communication screen.
2. Select the
icon to display the
favorites list.
3. Select the
icon.
4. Select the
icon.
5. The contact can be moved after it is selected.
6. Move the contact and select the
icon.
Changing contact name of your
favorites
1. Select the
icon on the home screen
and display the Communication screen.
2. Select the
icon to display the
favorites list.
3. Select the
icon.
4. Select the contact to display the keyboard screen.
5. If a new name is input and the
icon
is selected, the contact name is stored.
NOTE
If the contact is long-pressed when the
favorites list is displayed, the contact
information can be edited (deleted,
moved).
Telephone Number Input
NOTE
Practice this while parked until you are
confi dent you can do it while driving in a
non-taxing road situation. If you are not
completely comfortable, make all calls
from a safe parking position, and only
start driving when you can devote your full
attention to driving.
1. Input the telephone number using the numerical keypad.
2. Select the
icon to make the call.
Numeral or symbol entry
Use the numerical keypad.
Long-press the
icon to input +.
Select the
icon to delete the currently
input value.
Long-press the
icon to delete all input
values.
.B[EB@%$&""@&EJUJPOJOEC







5–103
Interior Features
Bluetooth®
Receiving an Incoming Call
When an incoming call is received, the incoming call notifi cation screen is displayed. The
“Incoming Call Notifi cation” setting must be on.
Refer to Communication Settings on page 5-107 .
To accept the call, press the pick-up button or select the
icon.
To reject the call, press the hang-up button or select the
icon.
The following icons are displayed on the screen during a call. Icons whi\
ch can be used differ
depending on use conditions.
Icon Function
Displays the Communication menu.
Ends the call.
Transferring a call from hands-free to a mobile phone
Communication between the hands-free unit and a device (Mobile phone) \
is canceled, and
the line can be switched to the device (Mobile phone) as a standard ca\
ll.
Transferring a call from a device (mobile phone) to hands-free
Communication between devices (mobile phone) can be switched to Blueto\
oth ® Hands-
Free.
Mute
The microphone can be muted during a call.
When selected again, the mute is canceled.
A call is made to other person during a call and a 3-way call can be made\
. Select the contact
from the following to make a call.
: Call History is displayed.
: The phonebook is displayed.
: The dial pad is displayed. Input the phone number.
The device may be unusable depending on the contractual content.
The call on hold is made to make a 3-way call.
The device may be unusable depending on the contractual content.
Switches the call on hold.
DTMF (Dual Tone Multi-Frequency Signal) Transmission
This function is used when transmitting DTMF via the Numerical Keypad. The receiver of
a DTMF transmission is generally a home telephone answering machine or a\
company's
automated guidance call center.
Input the number using a numerical keypad.
.B[EB@%$&""@&EJUJPOJOEC







5–106
Interior Features
Bluetooth®
The following icons are displayed in the lower part of the details on th\
e message. Icons
which can be used differ depending on use conditions.
Icon Function
Displays the Communication menu.
Displays the inbox.
Plays back a message.
When selected again, playback is temporarily stopped.
Displays the previous message.
Displays the next message.
Only replies to the sender of the currently displayed message.
Select the sentence on the displayed reply screen and select the sentenc\
e for sending from
the preset message.
Select the
icon.
Makes a call to a person who sent a message.
Deletes a message.
The messages stored in a device is also deleted.
NOTE
Up to three preset messages can be selected.
Editing preset messages
1. Select the
icon on the home screen and display the Communication screen.
2. Select the
icon.
3. Select the
icon.
4. Select the preset message which you would like to edit. The keyboard screen is displayed.
5. When the message is input and
is selected, the message is stored as a preset message.
NOTE
 y  Select the icon to change the language.  y Select the icon to switch between capitalized and lower-case characters. y Select the icon to return to the previous screen without storing the edit.
.B[EB@%$&""@&EJUJPOJOEC