warning light MAZDA MODEL 3 HATCHBACK 2014 Owners Manual (in English)

*Some models.7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
(Amber)
Forward
Obstruction
Warning/
Smart
City Brake
Support
(FOW/
SCBS)
Indicator
Light
*
The light turns on if the windshield and the radar
sensor are dirty or there is a malfunction in the
system. Verify the reason why the warning light is
illuminated on the audio display (page 7-24 ).
If the reason why the warning light is
illuminated is due to a dirty windshield, clean
the windshield.
If the warning light is illuminated because of a
dirty radar sensor, clean the front emblem.
For any other reasons, have the vehicle
inspected at an Authorized Mazda Dealer.
KEY Warning Light
Take the appropriate action and verify that the warning light turns off.
Signal Cause Action to be taken
(Red)
(Flashing) The advanced key battery is dead. Replace the battery (page 6-39 ).
The advanced key is not within the
operation range.
Bring the advanced key into the operation
range (page 3-7 ). The advanced key is placed in areas inside
the cabin where it is diffi cult for the key to
be detected.
A key from another manufacturer similar to
the advanced key is in the operation range. Take the key from another manufacturer
similar to the advanced key out of the
operation range.
Without the ignition switched off, the
advanced key is taken out of the cabin, and
then all the door are closed. Bring the advanced key back into the
cabin.
/C\FCA&('#*A'FKVKQPKPFD

*Some models.7–34
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Message Indicated on Display *
If a message is displayed in the type B audio display, take appropriate action (in a calm
manner) according to the displayed message.
(Display example)
Stop Vehicle in Safe Place Immediately
If the following messages are displayed in the Type B audio display, a vehicle system may
be malfunctioning. Stop the vehicle in a safe place and contact an Authorized Mazda Dealer.
Display Indicated Condition
Displays if the engine coolant temperature has increased
excessively.
Displays if the charging system has a malfunction.
/C\FCA&('#*A'FKVKQPKPFD

7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Make Sure the Message is No Longer Displayed
Displays in the following cases:
Display Indicated Condition/Action to be taken
Displays if i-ELOOP requires charging. Leave the engine
idling and wait until the message disappears.
NOTE
y If the vehicle is driven while the message is displayed, the
buzzer will sound.
y If you turn the steering wheel while the message is
displayed, it will feel heavier than normal, but this does
not indicate an abnormality. The steering operation will
return to normal after the message has disappeared.
/C\FCA&('#*A'FKVKQPKPFD

7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Warning Sound is Activated
Lights-On Reminder
The lights-on reminder is operable when
the time setting *1 of the auto headlight off
function is off.
If lights are on and the ignition is switched
to ACC or the ignition is switched off, a
continuous beep sound will be heard when
the driver's door is opened.
*1 If the light switch is left on, the auto
headlight off function automatically
turns off the lights about 30 seconds
after switching the ignition off. The
time setting can be changed.
Refer to Personalization Features on
page 9-12 .
NOTE
 


y When the ignition is switched to ACC,
the “Ignition Not Switched Off (STOP)
Warning Beep” (page 7-37 ) overrides
the lights-on reminder.
 


y A personalized function is available to
change the sound volume for the lights-
on reminder.
  Refer to Personalization Features on
page 9-12 .
Air Bag/Front Seat Belt
Pretensioner System Warning
Beep
If a malfunction is detected in the air bag/
front seat belt pretensioner systems and the
warning light illuminates, a warning beep
sound will be heard for about 5 seconds
every minute.
The air bag and seat belt pretensioner
system warning beep sound will continue
to be heard for approximately 35
minutes. Have your vehicle inspected at
an Authorized Mazda Dealer as soon as
possible.
WARNING
Do not drive the vehicle with the air
bag/front seat belt pretensioner system
warning beep sounding:
Driving the vehicle with the air bag/
front seat belt pretensioner system
warning beep sounding is dangerous.
In a collision, the air bags and the front
seat belt pretensioner system will not
deploy and this could result in death or
serious injury. Contact an Authorized
Mazda Dealer to have the vehicle
inspected as soon as possible.
/C\FCA&('#*A'FKVKQPKPFD

7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Seat Belt Warning Beep
If the driver's seat belt is not fastened
when the ignition is switched ON, a beep
sound will be heard for about 6 seconds. If
the driver or the front passenger's seat belt
is not fastened and the vehicle is driven
at a speed faster than about 20 km/h (12
mph), a beep sound will be heard again for
a specifi ed period of time.
NOTE




y Some models do not have the seat
belt warning function for the front
passenger's seat.
 


y Placing heavy items on the front
passenger seat may cause the front
passenger seat belt warning function to
operate depending on the weight of the
item.
 


y To allow the front passenger seat
weight sensor to function properly, do
not place and sit on an additional seat
cushion on the front passenger seat.
The sensor may not function properly
because the additional seat cushion
could cause sensor interference.
 


y When a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
Ignition Not Switched Off (STOP)
Warning Beep
If the driver's door is opened while
the ignition is switched to ACC, a
continuous beep sound will be heard to
notify the driver that the ignition has not
been switched off (STOP). Left in this
condition, the keyless entry system will
not operate, the car cannot be locked, and
the battery power will be depleted.
Key Removed from Vehicle
Warning Beep
A beep sound will be heard 6 times and
the KEY warning light (red) will fl ash
continuously if the ignition has not been
switched off, all the doors are closed, and
the key is removed from the vehicle. This
is to notify the driver that the key has been
removed from the vehicle and the ignition
has not been switched off.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key is
carried together with a metal object or it
is placed in a poor signal reception area.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with a door
open or ajar or the ignition has not been
switched off while the key is being carried,
a beep will be heard for about 2 seconds
to indicate that the doors and the liftgate/
trunk lid cannot be locked.
Key Left-in-luggage Compartment
Warning Beep (With the advanced
keyless function)
If the key is left in the trunk with all doors
locked and the trunk lid closed, a beep
sound is heard for about 10 seconds to
remind the driver the key has been left in
the trunk. If this happens, open the trunk
lid by pressing the electric trunk lid opener
and remove the key. A key removed from
the trunk may not function because its
functions may have been temporarily
suspended. To restore the key function,
perform the applicable procedure (page
3-8 ).
/C\FCA&('#*A'FKVKQPKPFD

7–38
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function)
If a key is left in the vehicle cabin and all
the doors and the trunk are locked using
a separate key, a beep sound is heard for
about 10 seconds to remind the driver
that the key has been left in the vehicle
cabin. If this happens, open the door and
remove the key. A key removed from the
vehicle this way may not function because
its functions may have been temporarily
suspended. Perform the applicable
procedure to restore the functions of the
key (page 3-8 ).
i-ELOOP Warning Beep
The beep will activate if you attempt to
drive the vehicle under the following
conditions.
 


y The i-ELOOP indicator light is fl ashing
green.
 


y “i-ELOOP” charging" is indicated in the
Type B audio display.
The beep will stop when the vehicle is
stopped. Make sure the indicator light is
no longer illuminated and the message
is no longer displayed before driving the
vehicle.
Tire Infl ation Pressure Warning
Beep
The warning beep sound will be heard
for about 3 seconds when there is any
abnormality in tire infl ation pressures
(page 4-104 ).
Lane Departure Warning System
(LDWS) Warning Sound
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
 


y The volume of the LDWS warning
sound can be changed.
  Refer to Personalization Features on
page 9-12 .




y The type of the LDWS warning sound
can be changed.
  Refer to Personalization Features on
page 9-12 .
Blind Spot Monitoring (BSM)
System Warning Beep
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the BSM warning light is illuminated.
NOTE
A personalized function is available to
change the BSM warning beep sound
volume.
Refer to Personalization Features on
page 9-12 .
Reversing
If vehicles approach from the rear on the
left and right, the Blind Spot Monitoring
(BSM) warning beep operates.
/C\FCA&('#*A'FKVKQPKPFD

*Some models.7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Mazda Radar Cruise Control
(MRCC) System Warnings *
The Mazda Radar Cruise Control (MRCC)
system warnings notify the driver of
system malfunctions and cautions on use
when required.
Check based on the beep sound.
Cautions What to check
The beep sounds 1 time
while the Mazda Radar
Cruise Control (MRCC)
is operating The vehicle speed is
slower than 25 km/h (16
mph) and the Mazda
Radar Cruise Control
(MRCC) system has
been canceled.
The beep sounds
continuously while
driving The distance between
your vehicle and the
vehicle ahead is too
close. Verify the safety
of the surrounding area
and reduce vehicle
speed.
When the Mazda
Radar Cruise Control
(MRCC) is operating,
the beep sounds and the
Mazda Radar Cruise
Control (MRCC)
warning light (amber)
in the instrument cluster
fl ashes. A malfunction in
the system may be
indicated. Have your
vehicle inspected at
an Authorized Mazda
Dealer.
Collision warning
If there is the possibility of a collision
with a vehicle or obstruction ahead, the
beep sounds continuously and a warning is
indicated in the display.
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or fl ashes and
the buzzer operates at the same time.
Refer to Warning/Indicator Lights on page
4-21 .
Over Rev. Buzzer *
The buzzer sounds to notify the driver if
the engine speed is about to exceed the
permissible engine speed.
CAUTION
Operate the accelerator and shift gears
according to the driving conditions so
that the buzzer does not sound. If the
engine speed exceeds the permissible
engine speed, the engine could be
damaged.
/C\FCA&('#*A'FKVKQPKPFD

8–24
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
13. Max. permissible infl ation pressure
14. SAFETY WARNING
P215/65R15 95H is an example of a tire size and load index rating. Here is an explanation
of the various components of that tire size and load index rating. Note that the tire size and
load index rating may be different from the example.
P
Indicates a tire that may be installed on cars, SUVs, minivans and light trucks as designated
by the Tire and Rim Association (T&RA).
NOTE
If your tire size does not begin with a letter this may mean it is designated by either ETRTO
(European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing
Association).
215
“215” is the nominal width of the tire in millimeters. This three-digit number gives the
width in millimeters of the tire from sidewall edge to sidewall edge. In general, the larger
the number, the wider the tire.
6 5
“65” is the aspect ratio. This two-digit number indicates the tire's ratio of height to width.
R
“R” is the tire construction symbol. R indicates “Radial ply construction”.
1 5
“15” is the wheel rim diameter in inches.
9 5
“95” is the Load Index. This two-or three-digit number indicates how much weight each tire
can support.
/C\FCA&('#*A'FKVKQPKPFD

9–14
Specifi cations
Personalization Features
Item Feature Factory Setting Available Settings
Lights-on reminder
*4 The volume of the lights-on reminder warning
alarm can be changed.
Refer to Settings on page 5-55 . Off High/Low/Off
Blind Spot
Monitoring (BSM)
system The volume of the BSM warning beep can be
changed.
*5
Refer to Settings on page 5-55 . High High/
Low/
Off
Lane Departure
Warning System
(LDWS) The warning sound for the Lane Departure
Warning System (LDWS) can be changed.
*6
Refer to Settings on page 5-55 . Beep Beep/Rumble Strip
The volume of the warning sound
for the Lane Departure Warning
System (LDWS) can be changed.
Refer to Settings on page 5-55 . Rumble
strip High High/Mid/Low
Beep High High/Low
The sensitivity of the warning for the Lane
Departure Warning System (LDWS) can be
changed.
Refer to Settings on page 5-55 . Low High/Low
The warning timing in which the Lane
Departure Warning System (LDWS)
determines that the vehicle may be deviating
from its lane can be changed.
Refer to Settings on page 5-55 . Before line At line/Before line
Meter display The distance unit can be changed.
Refer to Settings on page 5-55 . Miles or Km Miles/Km
The display language can be changed.
Refer to Settings on page 5-55 . English, French,
or Spanish English/
French/
Spanish
The temperature unit can be changed.
Refer to Settings on page 5-55 . F° or C° F°/C°
Forward Obstruction
Warning (FOW) The system can be changed so that Forward
Obstruction Warning (FOW) does not
operate.
*3
Refer to Settings on page 5-55 . On On/Off
The distance at which the collision warning
activates can be changed.
Refer to Settings on page 5-55 . Near Near/Far
The volume of the collision warning can be
changed.
Refer to Settings on page 5-55 . High High/Low/Off
Smart City Brake
Support (SCBS) The system can be changed so that Smart City
Brake Support (SCBS) does not operate.
*3
Refer to Settings on page 5-55 . On On/Off
Fuel Economy
Monitor Setting can be changed so that the ending
screen of the Fuel Economy Monitor is
displayed.
Refer to Fuel Economy Monitor on page 4-86 . OFF ON/OFF
/C\FCA&('#*A'FKVKQPKPFD

9–15
Specifi cations
Personalization Features
Item Feature Factory Setting Available Settings
Fuel economy
resetting procedure Setting can be changed so that the fuel
economy reset is linked with the trip meter
reset.
Refer to Fuel Economy Monitor on page 4-86 . OFF ON/OFF
Active driving
display Setting can be changed so that the Turn-by-
Turn (TBT) of the Active driving display is not
displayed.
Refer to Active driving display on page 4-19 . On On/Off
*1 If the setting is changed to Off, the following operation is performed according to the headlight switch position:
y At position: Headlights turn off immediately after the ignition is switched off.y At any position other than : Headlights do not turn off after the ignition is switched off.
*2 When set to Off, the lights-on reminder is operable.
*3 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda recommends
that these systems remain On.
*4 The setting of the lights-on reminder can be changed with the time setting of auto headlight off function set to
Off. Refer to Lights-On Reminder on page 7-36 .
*5 Only the volume of the warning beep during Blind Spot Monitoring (BSM) operation can be changed. The
volume of the warning beep during Rear Cross Traffi c Alert (RCTA) operation cannot be changed.
*6 For vehicles with an audio system other than the on-screen function type, the warning sound cannot be changed.
The warning sound is only a beep.
/C\FCA&('#*A'FKVKQPKPFD