ignition MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

6–73
Maintenance and Care
Appearance Care
Maintaining the Finish
Washing
CAUTION
  When the wiper lever is in the
position and the ignition is switched
ON, the wipers may move
automatically in the following cases:
 


 If the windscreen above the rain
sensor is touched or wiped with a
cloth.
 


 If the windscreen is struck with a
hand or other object from either
outside or inside the vehicle.
  Keep hands and scrapers clear of the
windscreen when the wiper lever is
in the
position and the ignition
is switched ON as fi ngers could be
pinched or the wipers and wiper
blades damaged when the wipers
activate automatically.
 If you are going to clean the
windscreen, be sure the wipers are
turned off completely (when it is
most likely that the engine is left
running) this is particularly important
when clearing ice and snow.
 
 Do not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems or
damage to electrical parts.
  When washing and waxing the
vehicle, be careful not to apply
excessive force to any single area
of the vehicle roof or the aerial.
Otherwise, you could dent the
vehicle or damage the aerial. To help protect the fi nish from rust
and deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface when:
 


 The vehicle is washed without fi rst
rinsing off dirt and other foreign matter.
 


 The vehicle is washed with a rough, dry,
or dirty cloth.
 


 The vehicle is washed at a car wash that
uses brushes that are dirty or too stiff.
 


 Cleansers or wax containing abrasives
are used.
NOTE
  Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
  Scratches are more noticeable on
vehicles with darker paint fi nishes.
To minimize scratches on the vehicle's
paint fi nish:




 Rinse off any dirt or other foreign matter
using lukewarm or cold water before
washing.
 


 Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
 


 Rub gently when washing or drying the
vehicle.
 


 Take your vehicle only to a car wash
that keeps its brushes well maintained.
 


 Do not use abrasive cleansers or wax
that contain abrasives.
.B[EB@&'&&"@&EJUJPOJOEC







7–11
If Trouble Arises
Flat Tyre
9. Remove the valve cap from the valve
of the fl at tyre, install the injection hose
to the tyre valve, turn the sleeve to the
right, and tighten it.
Valve cap Valve Injection hose
10. Install the bottle to the air compressor
and press it in until the left and right
tabs are engaged securely.
Tabs
11. Insert the air compressor plug into the
accessory socket inside the vehicle and
switch the ignition to ACC.
Refer to Accessory Sockets on page
5-155 .
Centre console
Compressor
Compressor plug
CAUTION
When inserting the air compressor
plug into or removing it from the
accessory socket, make sure that the air
compressor switch is OFF. When turning
the air compressor ON/OFF, use the air
compressor switch.
12. The sealant is injected into the tyre
when the air compressor is switched
ON. After the sealant is injected
completely, wait until the tyre infl ation
pressure increases to the specifi ed tyre
infl ation pressure.
NOTE
The infl ation pressure may increase
to about 300 kPa (3.1 kgf/cm 2 , 3 bar,
43.5 psi) temporarily to inject the
sealant through the valve. Normally, the
infl ation pressure decreases gradually
and it reaches the actual infl ation
pressure after about 30 seconds.
.B[EB@&'&&"@&EJUJPOJOEC







7–22
If Trouble Arises
Battery Runs Out
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and other
electrical parts beyond repair with a 24 V power supply (two 12 V batteries in series or a
24 V motor generator set).
Connect leads in numerical order and disconnect in reverse order.
Jumper leads
Booster battery
Discharged battery
.B[EB@&'&&"@&EJUJPOJOEC







7–26
If Trouble Arises
Overheating
Overheating
If the High engine coolant temperature
warning light illuminates, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WARNING
Switch the ignition to off and
make sure the fan is not running
before attempting to work near the
cooling fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running indefi nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the High engine coolant temperature
warning light illuminates:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine compartment.
If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the bonnet and start the engine.
If neither coolant nor steam is
escaping:
Open the bonnet and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an expert repairer,
we recommend an Authorised Mazda
Repairer.
6. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If it is low, look for coolant leaks from
the radiator and hoses.
.B[EB@&'&&"@&EJUJPOJOEC







7–29
If Trouble Arises
Emergency Towing
CAUTION
Follow these instructions when towing
the vehicle with all wheels on the
ground.
 
 Shift to neutral (Manual transaxle),
or the N position (Automatic
transaxle).
  Switch the ignition to ACC. 
 Release the parking brake.
Remember that power assist for the
brakes and steering will not be available
when the engine is not running.
Towing Hooks
CAUTION
  The towing eyelet should be used
in an emergency (to get the vehicle
out of a ditch or a snow bank, for
example).
  When using the towing eyelets,
always pull the lead or chain in a
straight direction with respect to the
eyelet. Never apply a sideways force.
NOTE
When towing with chain or lead, wrap
the chain or lead with a soft cloth near
the bumper to prevent damage to the
bumper.
.B[EB@&'&&"@&EJUJPOJOEC







7–32
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
If a Warning Light Turns On or Flashes
If any warning light turns on/fl ashes, take appropriate action for each light. There is no
problem if the light turns off, however if the light does not turn off or turns on/fl ashes again,
consult an Authorised Mazda Repairer.
(Vehicles with type C/type D audio)
The warning contents can be verifi ed on the audio.
1. Select the
icon on the home screen to display the applications screen.
2. Select the “Warning Guidance”.
Stop Vehicle in Safe Place Immediately
If any of the following warning lights turns on, the system may have a malfunction. Stop the
vehicle in a safe place immediately and contact an Authorised Mazda Repairer.
Signal Warning
Brake System Warning
Light
This warning has the following functions:
Parking brake warning/Warning light inspection
The light illuminates when the parking brake is applied with the ignition switched to
START or ON. It turns off when the parking brake is fully released.
Low brake fl uid level warning
If the brake warning light remains illuminated even though the parking brake is
released, the brake fl uid may be low or there could be a problem with the brake
system. Park the vehicle in a safe place immediately and contact an expert repairer, we
recommend an Authorised Mazda Repairer.
WARNING
Do not drive with the brake system warning light illuminated. Contact an expert
repairer, we recommend an Authorised Mazda Repairer to have the brakes
inspected as soon as possible:
Driving with the brake system warning light illuminated is dangerous. It
indicates that your brakes may not work at all or that they could completely fail
at any time. If this light remains illuminated, after checking that the parking
brake is fully released, have the brakes inspected immediately.
CAUTION
In addition, the effectiveness of the braking may diminish so you may need to
depress the brake pedal more strongly than normal to stop the vehicle.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
ABS Warning Light If the ABS warning light stays on while you're driving, the ABS control unit has detected a
system malfunction. If this occurs, your brakes will function normally as if the vehicle had
no ABS.
Should this happen, consult an expert repairer, we recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it is the result of the weak battery and
does not indicate an ABS malfunction.
Recharge the battery.
(With DSC vehicles)
The brake assist system does not operate while the ABS warning light is illuminated.
Check Engine Light If this light illuminates while driving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an expert repairer, we
recommend an Authorised Mazda Repairer.
The check engine light may illuminate in the following cases:
The fuel tank level being very low or approaching empty. The engine's electrical system has a problem. The emission control system has a problem.
If the check engine light remains on, or it fl ashes continuously , do not drive at high speeds
and consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible.
(Amber)
i-stop warning
light
*
When illuminated
If the i-stop warning light (amber) remains illuminated even after continuously pressing the
i-stop OFF switch under conditions other than when the bonnet is opened or the driver has
exited the vehicle (driver's seat belt is unfastened and driver's door is opened), consult an
expert repairer, we recommend an Authorised Mazda Repairer.
When fl ashing
The light fl ashes if there is any malfunction in the i-stop system. Consult an expert repairer,
we recommend an Authorised Mazda Repairer.
(Amber)
RVM warning light *
This warning light illuminates when the ignition is switched ON. The colour of the light
changes from amber to green when the rear vehicle monitoring system is operable, or
turns off when the system is turned off. The light stays on if the system has a malfunction.
Consult an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
This warning light may illuminate as a result of a temporary decrease in the sensitivity
of the radar sensor due to bad weather or dirt on the bumper surface. However, this does
not indicate a malfunction.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Automatic
Transaxle Warning
Light
*
The light/indication illuminates when the transaxle has a problem.
CAUTION
If the automatic transaxle warning light illuminates, the transaxle
has an electrical problem. Continuing to drive your Mazda in this
condition could cause damage to your transaxle. Consult an expert
repairer, we recommend an Authorised Mazda Repairer as soon as
possible.
Air Bag/Seat
Belt Pretensioner
System Warning
Light A system malfunction is indicated if the warning light constantly fl ashes, constantly
illuminates or does not illuminate at all when the ignition is switched ON. If any of these
occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible. The system may not operate in an accident. WARNING
Never tamper with the air bag/pretensioner systems and always have an expert
repairer, we recommend an Authorised Mazda Repairer perform all servicing and
repairs:
Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner
could accidentally activate or become disabled causing serious injury or death.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–38
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Tyre Pressure
Monitoring System
Warning Light
*
If the tyre pressure monitoring system has a malfunction, the tyre pressure warning
light fl ashes for about 1 minute when the ignition is switched ON and then continues
illuminating. Have your vehicle checked by an expert repairer, we recommend an
Authorised Mazda Repairer as soon as possible.
WARNING

If the tyre pressure monitoring system warning light illuminates or fl ashes, or the
tyre pressure warning beep sound is heard, decrease vehicle speed immediately and
avoid sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or fl ashes, or the
tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high
speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a fl at, pull over to a safe position where you
can check the visual condition of the tyre and determine if you have enough air
to proceed to a place where air may be added and the system monitored again by
an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair
station.
Do not ignore the TPMS Warning Light:
Ignoring the TPMS warning light is dangerous, even if you know why it is
illuminated. Have the problem taken care of as soon as possible before it develops
into a more serious situation that could lead to tyre failure and a dangerous accident.
(Red)
(Illuminate)
KEY Warning Light If any malfunction occurs in the keyless entry system, it illuminates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light
(amber) fl ashes, the engine may not start. If the engine cannot be started, try starting it
using the emergency operation for starting the engine, and have the vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Amber)
(Flashing)
Lane Departure
Warning System
(LDWS) Warning
Light
*
The warning light fl ashes when the system has a malfunction. Have your vehicle inspected
at an expert repairer, we recommend an Authorised Mazda Repairer.
The LDWS does not operate when the warning light fl ashes.
CAUTION
If any of the following cases occurs, the system may have a malfunction. Have the
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light fl ashes while the vehicle is being driven. The light does not illuminate when the ignition is switched ON. Always use tyres for all wheels that are of the specifi ed size, and the same
manufacture, brand, and tread pattern. In addition, do not use tyres with signifi cantly
different wear patterns on the same vehicle. If such improper tyres are used, the
LDWS may not operate normally.
When an emergency spare tyre is used, the system may not operate normally.
Headlight
Auto-Levelling
Malfunction
Indicator Light
*
This indicator light stays on for a few seconds when the ignition is switched ON.
Thereafter, the indicator light will illuminate when the headlight auto-levelling system has
a malfunction.
If the indicator light illuminates, contact an expert repairer, we recommend an Authorised
Mazda Repairer.
NOTE
Vehicles with the adaptive front lighting system (AFS) are not equipped with the
headlight auto-levelling malfunction indicator light. If there is a malfunction with the
headlight auto-levelling function, the AFS OFF indicator light fl ashes.
(Amber)
High Beam Control
System (HBC)
Warning Light
*
When illuminated
The warning light illuminates if the area of the windscreen in front of the forward sensing
camera (FSC) is fogged or obstructed.
When fl ashing
This light fl ashes if there is a malfunction in the high beam control system (HBC). Have
your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
(Flashing)
Mazda Radar
Cruise Control
(MRCC) Warning
Light
*
The warning light fl ashes if there is a malfunction in the system while the Mazda Radar
Cruise Control (MRCC) system is on. Have your vehicle inspected at an expert repairer, we
recommend an Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC