steering wheel MAZDA MODEL 3 HATCHBACK 2015 (in English) Owner's Manual

4–111
When Driving
i-ACTIVSENSE
NOTE
  The LDWS remains on stand-by
until it detects white or yellow lines
on both the left and right sides, or on
either side.
  When the system detects a white
or yellow line on one side only, the
system will operate the warning only
when the vehicle deviates to the side
the white or yellow line detected.
Auto cancel
Under the following conditions, the
LDWS is automatically cancelled and
kept on stand-by, and the LDWS warning
light (amber) in the instrument cluster
illuminates.
 


 The system cannot detect white or
yellow lines.
 


 The vehicle speed is less than about 65
km/h (40 mph).
 


 The vehicle is making a sharp turn.



 The vehicle is making a turn at an
inadequate speed.
 


 The temperature inside the camera is
high or low.
 


 The windscreen around the camera is
foggy.
 


 The windscreen around the camera is
blocked by an obstruction, causing poor
forward visibility.
The lane indication (bordered line) is
indicated in the active driving display
(Type A instrument cluster
*1 ) or the multi
information display (Type B instrument
cluster
*1 ).
The LDWS is automatically enabled when
the condition changes and the system is
operable.
*1 To determine which instrument cluster
is equipped on your Mazda, Refer to
Meters and Gauges on page 4-24 .
Auto cancel of warning
Under the following conditions, the
LDWS determines that the driver is
making lane changes and the warning is
automatically cancelled.
The LDWS is automatically enabled after
the operation.
 


 The steering wheel is operated abruptly.



 The brake pedal is depressed abruptly.



 The accelerator pedal is depressed
abruptly.
 


 A direction indicator lever is operated
(after the direction indicator lever is
returned, the LDWS warning may not
operate for about 3 seconds which is the
period of time required to make a lane
correction).
.B[EB@&'&&"@&EJUJPOJOEC







4–112
When Driving
i-ACTIVSENSE
NOTE
  After about 5 seconds have elapsed
with the direction indicator lever left
operating, the LDWS warning may
operate if the vehicle is close to a
white or yellow line.
  The sensitivity of the warning
(sensitivity with which the system
determines the driver's intentional
lane change) can be changed.
 Refer to Personalisation Features on
page 9-16 .
Cancelling the System
To cancel the LDWS, press the LDWS
switch. The LDWS indicator light (Green/
Amber) in the instrument cluster turns off.
The lane indication displayed in the
active driving display (Type A instrument
cluster
*1 ) or the multi information display
(Type B instrument cluster *1 ) turns off.
*1 To determine which instrument cluster
is equipped on your Mazda, Refer to
Meters and Gauges on page 4-24 .
LDWS Warning
If the system determines that the vehicle
may be deviating from its lane while the
system is operating, the LDWS warning
sounds and the LDWS indicator light
(green) fl ashes.
Refer to Lane Departure Warning System
(LDWS) Warning Sound on page 7-52 .
In the active driving display (Type
A instrument cluster
*1 ) or the multi
information display (Type B instrument
cluster
*1 ), the direction in which the
system determined that the vehicle may
be deviating from its lane is indicated.
Operate the steering wheel adequately and
drive in the centre of the lane.
*1 To determine which instrument cluster
is equipped on your Mazda, Refer to
Meters and Gauges on page 4-24 .
Indication on display
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–133
When Driving
i-ACTIVSENSE
Adjustable Speed Limiter *
The adjustable speed limiter is a function to prevent the vehicle from being driven at a
vehicle speed faster than a set speed. The vehicle speed is controlled to kept it below the set
speed even if the accelerator pedal is depressed.
The adjustable speed limiter can be set between 30 km/h (20 mph) and 200 km/h (125 mph).
The vehicle speed may exceed the set speed when the vehicle is driven on a down slope,
however, the system notifi es the driver by fl ashing the display and operating a warning
sound.
WARNING
Always turn off the system when changing drivers:
If the driver is changed and the new driver is unaware of the adjustable speed limiter
function, the vehicle may not accelerate when the driver depresses the accelerator
pedal, leading to an accident.
The system consists of the adjustable speed limiter display and the speed limiter switch on
the steering wheel.
CANCEL switch
Speed limiter switchSpeed limiter switch RESUME switch Cruise Control SystemMazda Radar Cruise Control (MRCC)
SET+/SET- switchCANCEL switch
RESUME switch
SET+/SET- switch
Active Driving Display Display in the instrument cluster
With multi
information displayWithout multi
information display
.B[EB@&'&&"@&EJUJPOJOEC







4–142
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) system will not operate if the driver is
deliberately performing driving operations (accelerator pedal and steering wheel).
  The Smart City Brake Support (SCBS) system will operate under the following
conditions.
 


 The engine is running.



 The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



 The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



 The Smart City Brake Support (SCBS) system is not turned off.



 The DSC operation is not turned off using the DSC OFF switch.



 The DSC is not malfunctioning. 

 The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam refl ected off the refl ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
 


 Refl ection of the laser is poor due to the shape of the vehicle ahead.



 The vehicle ahead is signifi cantly dirty.



 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 The windscreen is dirty.



 The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
profi le.




 Vehicles with certain shapes such as a vehicle carrier. 

 Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat.



 If there is the possibility of partial contact with a vehicle ahead.



 When driving on continuously curving roads, and entering and exiting exits.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front).
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.
.B[EB@&'&&"@&EJUJPOJOEC







4–14 6
When Driving
i-ACTIVSENSE
NOTE
  The Smart Brake Support (SBS) system operates when all of the following conditions
are met:
 


 The ignition is switched ON.



 The Smart Brake Support (SBS) system is on.



 The DSC OFF indicator light is not illuminated.



 The vehicle speed is about 15 km/h or faster (10 mph or faster).



 The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


 The Dynamic Stability Control (DSC) is not operating. 

 The Smart Brake Support (SBS) system may not operate under the following
conditions:
 


 If there is the possibility of hitting only a part of a vehicle ahead.



 If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



 The vehicle is driven at the same speed as the vehicle ahead.



 The accelerator pedal is depressed.



 The brake pedal is depressed.



 The steering wheel is being operated.



 The selector lever is being operated.



 The direction indicator is being used. 

 Although the objects which activate the system are 4-wheeled vehicles, the radar
sensor could detect the following objects, determine them to be an obstruction, and
operate the Smart Brake Support (SBS) system.
 


 Objects on the road at the entrance to a curve (including guardrails and snow banks).



 A vehicle appears in the opposite lane while cornering or rounding a curve.



 When crossing a narrow bridge.



 When passing under a low gate or through a tunnel or narrow gate.



 When entering an underground parking area.



 Metal objects, bumps, or protruding objects on the road.



 If you suddenly come close to a vehicle ahead.



 When driving in areas where there is high grass or forage.



 Two-wheeled vehicles such as motorbikes or bicycles.



 Pedestrians or non-metallic objects such as standing trees. 

 When the system operates, the user is notifi ed by the fl ashing Smart Brake Support
(SBS) indicator light (red) and the active driving display.
  The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction.
 Refer to Warning Lights on page 4-41 .
.B[EB@&'&&"@&EJUJPOJOEC







4–169
When Driving
Rear View Monitor
Viewing the Display
Guide lines which indicate the width of the vehicle (yellow) are displayed on the screen as a
reference to the approximate width of the vehicle in comparison to the width of the parking
space you are about to back into.
Use this display view for parking your vehicle in a parking space or garage.
b
a
a) Vehicle width guide lines (yellow)
These guide lines serve as a reference to the approximate width of the vehicle.
b) Distance guide lines.
These guide lines indicate the approximate distance to a point measured from the
vehicle's rear (from the end of the bumper).
The red and yellow lines indicate the points about 50 cm (19 in) for the red line and 100
cm (39.3 in) for the yellow lines from the rear bumper (at the centre point of each of the
lines).
CAUTION
The guide lines on the screen are fi xed lines. They are not synced to the driver's turning
of the steering wheel. Always be careful and check the area to the vehicle's rear and the
surrounding area directly with your eyes while backing up.
.B[EB@&'&&"@&EJUJPOJOEC







4–170
When Driving
Rear View Monitor
Rear View Monitor Operation
The operation of the rear view monitor when reversing the vehicle varies depending on
the traffi c, road, and vehicle conditions. The amount of steering and the timing also varies
depending on conditions, so confi rm the surrounding conditions directly with your eyes and
steer the vehicle in accordance with the conditions.
Be well aware of the above cautions prior to using the rear view monitor.
NOTE
Images displayed on the monitor from the rear view parking camera are reversed images
(mirror images).
1. Shift the shift lever to R to switch the display to the rear view monitor display.
2. Confi rming the surrounding conditions, reverse the vehicle.
(Display condition) (Vehicle condition)
3. After your vehicle begins entering the parking space, continue backing up slowly so that
the distance between the vehicle width lines and the sides of the parking space on the left
and right are roughly equal.
4. Continue to adjust the steering wheel until the vehicle width guide lines are parallel to
the left and right sides of the parking space.
.B[EB@&'&&"@&EJUJPOJOEC







5–20
Interior Features
Audio System
CAUTION
When washing the inside of the window
which has an aerial, use a soft cloth
dampened in lukewarm water, gently
wiping the aerial lines.
Use of glass cleaning products could
damage the aerial.
Operating Tips for Audio
System
WARNING
Always adjust the audio while the
vehicle is stopped:
Do not adjust the audio control
switches while driving the vehicle.
Adjusting the audio while driving
the vehicle is dangerous as it could
distract your attention from the vehicle
operation which could lead to a serious
accident.
Even if the audio control switches are
equipped on the steering wheel, learn
to use the switches without looking
down at them so that you can keep your
maximum attention on the road while
driving the vehicle.
CAUTION
For the purposes of safe driving, adjust
the audio volume to a level that allows
you to hear sounds outside of the vehicle
including car horns and particularly
emergency vehicle sirens.
.B[EB@&'&&"@&EJUJPOJOEC







5–97
Interior Features
Bluetooth®
Microphone (hands-free)
The microphone is used for speaking voice commands or when making a Hands-free call.
Talk button, Pick-Up button and Hang-Up button (hands-free)
The basic functions of Bluetooth
® Hands-Free can be used for such things as making calls or
hanging up using the talk, pick-up and hang-up buttons on the steering wheel.
Commander switch (Type C/Type D)
The commander switch is used for volume adjustment and display operation. Tilt or turn the
commander knob to move the cursor. Press the commander knob to select the icon.
Volume adjustment
The power/volume dial of the audio unit
*1 or the volume dial of the commander switch *2
is used to adjust the volume. Turn the dial to the right to increase volume, to the left to
decrease it.
The volume can also be adjusted using the volume button on the steering wheel.
*1 Type A/Type B
*2 Type C/Type D
NOTE
If the volume is lower compared to other audio modes, increase the volume from the
device side.
(Type C/Type D)
Conversation volume and the volume of the voice guidance and ringtone can each be set in
advance.
1. Select the
icon on the home screen and display the Communication screen.
2. Select
.
3. Adjust the
and the using the slider.
.B[EB@&'&&"@&EJUJPOJOEC







5–130
Interior Features
Bluetooth®
NOTE
  If the ignition is switched off
during a hands-free call, the line is
transferred to the device (Mobile
phone) automatically.
  If the DTMF code has two or more
digits or symbols, each one must be
transmitted individually.
Call Interrupt
A call can be interrupted to receive an
incoming call from a third party.
When
is selected or the pick-
up button on the steering wheel is pressed,
the current call is held and the system
switches to the new incoming call.
When
is selected, the current
call is ended and the system switches to
the new incoming call (GSM network
only).
When
is selected or the hang-up
button on the steering wheel is pressed, an
incoming call is refused.
NOTE
  The function may not be available
depending on the contractual content
of the mobile device.
  The function may not be operable
depending on the type of the
telephone network and the mobile
device.
Receiving and Replying to
Messages (available only with
E-mail/SMS compatible phones)
SMS (Short Message Service) messages,
and E-mail received by connected devices
can be downloaded, displayed, and played
(read by the system).
Additionally, replies can also be made
to calls and messages in the received
messages.
Downloading messages
Up to 20 new messages can be
downloaded and displayed from a
connected device.
NOTE
For e-mail, 20 messages for each
account can be downloaded.
(Automatic downloading)
The “Auto Download Email” (E-mail) or
“Auto Download SMS” (SMS) setting
must be on. A message is downloaded
automatically when the Bluetooth
® unit is
connected to the device.
Refer to Communication Settings on page
5-134 .
(Manually downloading)
When the “Auto Download Email”
(E-mail) or “Auto Download SMS” (SMS)
setting is off, the message is downloaded
using the following procedure.
1. Select the
icon on the home screen
and display the Communication screen.
2. Select
or to display the
Inbox.
3. Select
.
.B[EB@&'&&"@&EJUJPOJOEC