steering wheel MAZDA MODEL 3 HATCHBACK 2015 (in English) User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL 3 HATCHBACK, Model: MAZDA MODEL 3 HATCHBACK 2015Pages: 689, PDF Size: 7.08 MB
Page 165 of 689
4–15
When Driving
Start/Stop Engine
NOTE
To ensure safe and comfortable use of the vehicle, the i-stop function controls engine stop
and restart automatically while constantly monitoring operations other than those of the
driver, such as the vehicle's interior and exterior environment, and the operational status
of the vehicle.
The engine stops automatically when all of the following conditions are met:
The engine has been started and the vehicle is driven for a certain period. The i-stop
function will not operate if the vehicle is not fi rst driven, no matter how long the
engine is left idling. Also, after the vehicle is driven for a certain period and then
stopped, the i-stop function (automatic engine-stop and restart) operates only once
while the vehicle is stopped.
The engine is started with the bonnet closed.
(SKYACTIV-G 1.5, SKYACTIV-G 2.0)
The engine has warmed up suffi ciently.
(Manual transaxle)
The vehicle speed is about 3 km/h (2 mph) or less.
(Automatic transaxle)
The vehicle is stopped.
The battery is in good condition.
The bonnet is closed.
All the doors and the liftgate/boot lid are closed.
The driver's seat belt is fastened.
The windscreen defroster switch is off.
(Dual-zone automatic air-conditioning)
The temperature setting dial for the air conditioning is set to a position other than
maximum heating/maximum cooling (A/C ON).
(Dual-zone automatic air-conditioning)
The vehicle's interior temperature and the set temperature for the air-conditioning
system are nearly the same.
(European model)
The vehicle is driven at elevations of 1,800 meters (5,905 ft) or less.
(Except European model)
The vehicle is driven at elevations of 1,500 meters (4,921 ft) or less.
The i-stop warning light (amber) is not illuminated or fl ashing.
The keyless entry system operate normally.
The brakes are applied suffi ciently (brake system vacuum level is suffi cient).
The steering wheel is not being operated.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 166 of 689
4–16
When Driving
Start/Stop Engine
NOTE
(Automatic transaxle)
The selector lever is in the D/M position (not second gear fi xed mode) or the N
position.
The automatic transaxle fl uid has warmed up suffi ciently.
The automatic transaxle fl uid temperature is not abnormally high.
The steering wheel is positioned so that the wheels are pointed nearly straight ahead
(if force is applied to the steering wheel even with the wheels pointed straight ahead,
the i-stop function may not operate. Loosen your grip on the steering wheel to allow
the i-stop function to operate).
The brake pedal is depressed to stop the vehicle (if the i-stop indicator light (green)
fl ashes without the i-stop function operating, it is possible that the brake pedal
has not been depressed suffi ciently. Depress the brake pedal a little more strongly
(except European model)).
Emergency braking is not applied.
The vehicle is not stopped on a steep grade in a place such as a multilevel car
parking facility.
(SKYACTIV-D 2.2)
The fuel injection learning, which occurs periodically and automatically, is not
performed.
If any one of the following conditions occurs, extra time may be required for the
engine to stop automatically.
Battery power is depleted as a result of not using the vehicle for a long period.
The ambient temperature is high or low.
The battery leads have been disconnected for battery replacement and then
reconnected.
(SKYACTIV-D 2.2)
Particulate Matter (PM) is eliminated by the diesel particulate fi lter.
For safety reasons, if any one of the following operations is performed after the engine
has been automatically stopped, the i-stop warning light (amber) illuminates and the
engine will not restart automatically even if the clutch pedal is depressed (manual
transaxle) or the brake pedal is released (automatic transaxle). If this occurs, use the
standard engine starting procedure to start the engine.
The bonnet is opened.
The driver intends to get out of the vehicle (driver's seat belt is unfastened and
driver's door is opened).
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 168 of 689
4–18
When Driving
Start/Stop Engine
NOTE
If any one of the following operations is performed after the engine has been
automatically stopped (shift lever is in neutral position for vehicles with manual
transaxle), the engine will restart automatically even though the clutch pedal is not
depressed (manual transaxle) or the brake pedal is not released (automatic transaxle).
However, for safety reasons, if the shift lever is in a position other than neutral for
vehicles with manual transaxle, the engine will not restart automatically.
The i-stop OFF switch is pressed for several seconds.
(Dual-zone automatic air-conditioning)
The temperature setting dial of the air conditioning is set to maximum heating/
maximum cooling (A/C ON).
The windscreen defroster switch is on.
(Except European model)
The driver intends to get out of the vehicle (driver's seat belt is unfastened and any
door or the liftgate/boot lid is opened).
The brakes are released slightly on a slope and the vehicle begins to move.
(Automatic transaxle)
The accelerator pedal is depressed while the selector lever is in the D/M position
(not second gear fi xed mode).
The selector lever is shifted to the R position.
The selector lever is shifted from the N or P position to the D/M position (not second
gear fi xed mode).
The steering wheel is operated with the selector lever in the D/M position (not
second gear fi xed mode).
The selector lever is in the M position, second gear fi xed mode.
If any one of the following vehicle conditions occur after the engine has been
automatically stopped (shift lever is in neutral position for vehicles with manual
transaxle), the engine will restart automatically even though the clutch pedal is not
depressed (manual transaxle) or the brake pedal is not released (automatic transaxle).
However, for safety reasons, if the shift lever is in a position other than neutral for
vehicles with manual transaxle, the engine will not restart automatically.
(Dual-zone automatic air-conditioning)
There is a large difference between the cabin temperature and the temperature set for
the air-conditioning system.
Two minutes have elapsed since the i-stop function started operating.
The battery power is depleted.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 206 of 689
*Some models.4–56
When Driving
Transaxle
Using steering shift switch *
To shift up to a higher gear with the
steering shift switches, pull the UP switch
(
) toward you once with your
fi ngers.
UP switch (+/OFF)
WARNING
Keep your hands on the steering wheel
rim when using fi ngers on the steering
shift switches (6-speed transaxle
model):
Putting your hands inside the rim of
the steering wheel when using the
steering shift switches is dangerous. If
the driver's air bag were to deploy in a
collision, your hands could be impacted
causing injury.
NOTE
When driving slowly, the gears may
not shift up.
In manual shift mode, do not run the
engine with the tachometer needle
in the RED ZONE. When the engine
rpm is high, a gear may shift up
automatically to protect the engine.
NOTE
When depressing the accelerator
fully, the transaxle will shift to a
lower gear, depending on vehicle
speed.
The steering shift switch can be used
temporarily even if the selector lever
is in the D position while driving. In
addition, it returns to automatic shift
mode when the UP switch (
)
is pulled rearward for a suffi cient
amount of time.
Manually shifting down
You can shift gears down by operating the
shift lever or the steering shift switches
* .
4-speed transaxle model : M4 : M3 :
M2: M1
6-speed transaxle model : M6 : M5 :
M4: M3 : M2: M1
Using selector lever
To shift down to a lower gear, tap the
selector lever forward
once.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 207 of 689
*Some models.4–57
When Driving
Transaxle
Using steering shift switch *
To shift down to a lower gear with the
steering shift switches, pull the DOWN
switch
toward you once with your
fi ngers.
DOWN switch (-)
WARNING
Do not use engine braking on slippery
road surfaces or at high speeds:
Shifting down while driving on wet,
snowy, or frozen roads, or while driving
at high speeds causes sudden engine
braking, which is dangerous. The
sudden change in tyre speed could
cause the tyres to skid. This could
lead to loss of vehicle control and an
accident.
Keep your hands on the steering wheel
rim when using fi ngers on the steering
shift switches: (6-speed transaxle
model)
Putting your hands inside the rim of
the steering wheel when using the
steering shift switches is dangerous. If
the driver's air bag were to deploy in a
collision, your hands could be impacted
causing injury.
NOTE
When driving at high speeds, the
gear may not shift down.
During deceleration, the gear may
automatically shift down depending
on vehicle speed.
When depressing the accelerator
fully, the transaxle will shift to a
lower gear, depending on vehicle
speed.
Second gear fi xed mode
When the selector lever is moved back
while the vehicle speed is about 10 km/h
(6.2 mph) or less, the transaxle is set in the
second gear fi xed mode. The gear is fi xed
in second while in this mode for easier
acceleration from a stop and driving on
slippery roads such as snow-covered
roads.
If the selector lever is moved back
or
forward
while in the second gear fi xed
mode, the mode will be cancelled.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 230 of 689
4–80
When Driving
Switches and Controls
Horn
To sound the horn, press the mark on
the steering wheel.
Hazard Warning Flasher
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffi c hazard
and that they must take extreme caution
when near it.
Depress the hazard warning fl asher and
all the direction indicators will fl ash. The
hazard warning indicator lights in the
instrument cluster fl ash simultaneously.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 243 of 689
4–93
When Driving
i-ELOOP
i-ELOOP Indicator Light/Control
Status Display
The driver is notifi ed of the i-ELOOP
power generating status and the vehicle
conditions by the i-ELOOP indicator light
and the control status display.
i-ELOOP Indicator Light
Illuminated (vehicle without type C/type
D audio)
The light turns on during power
generation.
Flashing
If the engine is started after the vehicle has
not been driven for a long period of time,
the i-ELOOP indicator light may fl ash.
Leave the engine idling and wait until the
indicator light turns off.
NOTE
The beep will sound if the vehicle is
driven while the i-ELOOP indicator
light is fl ashing. In addition, if you
turn the steering wheel while the
light is fl ashing, it will feel heavier
than normal, but this does not
indicate an abnormality. Stop the
vehicle in a safe location with the
engine running and do not attempt to
turn the steering wheel. The steering
operation will return to normal after
the i-ELOOP indicator light stops
fl ashing.
(Vehicles with type C/type D audio) A notifi cation is displayed in the
centre display and the i-ELOOP
indicator light fl ashes at the same
time.
Refer to Warning Message Indicated
on Display on page 7-47 .
Control status display (vehicles with
type C/type D audio)
The i-ELOOP power generating status is
displayed in the centre display.
Refer to Control Status Display on page
4-95 .
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 249 of 689
4–99
When Driving
Power Steering
Power Steering
Power steering is only operable when
the engine is running. If the engine is
off or if the power steering system is
inoperable, you can still steer, but it
requires more physical effort.
If the steering feels stiffer than usual
during normal driving or the steering
vibrates, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
The warning light notifi es the driver
of system abnormalities and operation
conditions.
In addition, the buzzer may also activate
depending on the system abnormality or
operation condition.
Refer to Warning Lights on page 4-41 .
Refer to Power Steering Warning Buzzer
on page 7-53 .
CAUTION
Never hold the steering wheel to the
extreme left or right for more than
5 seconds with the engine running.
This could damage the power steering
system.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 253 of 689
*Some models.4–103
When Driving
i-ACTIVSENSE
Adaptive Front Lighting
System (AFS)
*
The adaptive front lighting system (AFS)
automatically adjusts the headlight beams
to the left or right in conjunction with the
operation of the steering wheel after the
headlights have been turned on.
AFS OFF Indicator Light
When illuminated
This indicator light illuminates briefl y
when the ignition is switched ON, and
then turns off. Pressing the AFS OFF
switch cancels the AFS function and
illuminates the indicator light.
When fl ashing
The indicator light fl ashes continuously
if the system is malfunctioning. Consult
an expert repairer, we recommend an
Authorised Mazda Repairer.
NOTE
Even if the AFS is not operating due
to some malfunction, the normal
headlight function is still operable.
If there is a malfunction with the
headlight auto-levelling function, the
indicator light fl ashes.
AFS OFF switch
Pressing the AFS OFF switch turns off the
AFS. The AFS OFF indicator light in the
instrument cluster illuminates.
Pressing the AFS OFF switch again turns
off the switch illumination and turns on
the AFS operation. The AFS OFF indicator
light turns off.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 258 of 689
4–10 8
When Driving
i-ACTIVSENSE
WARNING
Do not use the LDWS under the following conditions:
The system may not operate adequately according to the actual driving conditions,
resulting in an accident.
Driving on roads with tight curves.
Driving under bad weather conditions (rain, fog, and snow).
The functions of the LDWS have limitations:
Always stay on course using the steering wheel and drive with care. The system is not
designed to compensate for a driver’s lack of caution and if you rely too much on the
LDWS it could lead to an accident. The driver is responsible for assuring lane changes
and other manoeuvres. Always pay attention to the direction in which the vehicle is
travelling and the vehicle’s surroundings.
CAUTION
Do not modify the suspension. If the vehicle height or the damping force of the
suspensions is changed, the LDWS may not operate correctly.
NOTE
If your vehicle deviates from its traffi c lane, the LDWS operates (warning sound and
indicator light). Steer the vehicle adequately to drive the vehicle to the centre of the
lane.
When the direction indicator lever is operated for a lane change, the LDWS warning
is automatically cancelled. The LDWS warning becomes operable when the direction
indicator lever is returned and the system detects the white or yellow lines.
If the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white or yellow line, the system determines that the driver is
making a lane change and the LDWS warning is automatically cancelled.
The LDWS may not operate during the period immediately after the vehicle has
deviated from its lane and the LDWS has operated, or the vehicle deviates from its
lane repeatedly within a short period of time.
The LDWS does not operate if it does not detect the white or yellow lines of the traffi c
lane.
. B [ E B @ & ' & & " @ & E J U J P O J O E C