warning light MAZDA MODEL 3 HATCHBACK 2015 (in English) Owner's Manual

*Some models.3–46
Before Driving
Security System
Theft-Deterrent System
(With the Intrusion
Sensor)
*
If the theft deterrent system detects an
inappropriate entry into the vehicle or the
intrusion sensor detects movement in the
vehicle which could result in the vehicle or
its contents being stolen, the alarm alerts
the surrounding area of an abnormality by
sounding the siren and fl ashing the hazard
warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
The intrusion sensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.
The intrusion sensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
 
 Do not hang clothing or objects from
a head restraint or a coat hook.
  Return the extension sunvisors to
their original positions.
  Do not blind the intrusion sensor by
covering it or placing objects over it.
  Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
  Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
  Do not install seats or seat covers
that are not Mazda genuine products.
  To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

Intrusion sensor and
intrusion sensor bezel
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.3–47
Before Driving
Security System
Operation
Siren triggering conditions
The siren sounds intermittently and the
hazard warning lights fl ash for about 30
seconds when the system is triggered by
any one of the following:
 


 Unlocking a door with the key or an
inside door-lock knob.
 


 Forcing open a door, the bonnet or the
liftgate/boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
 


 The intrusion sensor detects a movement
in the vehicle.
The system will be triggered again (up to
10 times) if one of the above conditions
remains.
 


 Disconnecting the battery terminal (the
hazard warning lights do not fl ash).
The system will be triggered about 10
times.
NOTE
If the battery goes dead while the theft-
deterrent system is armed, the siren will
activate and the hazard warning lights
will fl ash when the battery is charged or
replaced.
How to Arm the System
1. Close the windows and the sunroof *
securely.
NOTE
Even with a window or the sunroof *
open, the system can be armed,
however, leaving the windows and the
sunroof
* even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion/Tilt
Sensor on page 3-48 .
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and
the liftgate/boot lid are closed.
4. Press the lock button on the transmitter.
The hazard warning lights will fl ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument panel fl ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.3–48
Before Driving
Security System
NOTE
  The theft deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate/boot lid and the bonnet
closed.
 Refer to Transmitter on page 3-4 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door or the liftgate/
boot lid .
 


 Opening the bonnet.



 Switching the ignition ON.

 To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter while the theft-deterrent
system is armed, the hazard warning
lights will fl ash once to indicate that
the system is armed.
Cancelling the Intrusion Sensor
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
(Intrusion sensor)
 


 Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
 


 Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
 


 Hanging small objects/accessories in
the vehicle, hanging clothing on a coat
hook, or placing other items which can
move easily inside the vehicle.
 


 Parking in an area where there is strong
vibration or loud noise.
 


 When using a high pressure or automatic
car wash.
 


 Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
 


 Doors are locked with a window or the
sunroof* left open. 


 An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the liftgate/boot lid
remains closed for 30 seconds, all
the doors and the liftgate/boot lid
automatically re-lock and the theft
deterrent system arms even if a window
and the sunroof
* is left open.
.B[EB@&'&&"@&EJUJPOJOEC







3–49
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will fl ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove compartment.
Mazda recommends that you affi x it to the
lower rear corner of a front door window.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.3–50
Before Driving
Security System
Theft-Deterrent System
(Without the Intrusion
Sensor)
*
If the theft deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and fl ashing the hazard
warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Operation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights fl ash for about 30
seconds when the system is triggered by
any one of the following:
 


 Unlocking a door with the key or an
inside door-lock knob.
 


 Forcing open a door, the bonnet or the
liftgate/boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
If the system is triggered again, the lights
and horn will activate until the driver's
door or the liftgate/boot lid is unlocked
with the transmitter.
(With advanced key)
The lights and horn can also be
deactivated by pressing the request switch
on a door.
NOTE
If the battery goes dead while the theft-
deterrent system is armed, the horn will
activate and the hazard warning lights
will fl ash when the battery is charged or
replaced.
How to Arm the System
1. Close the windows and the sunroof *
securely.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and
the liftgate/boot lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will fl ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument panel fl ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
.B[EB@&'&&"@&EJUJPOJOEC







3–51
Before Driving
Security System
NOTE
  The theft deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate/boot lid and the bonnet
closed.
 Refer to Transmitter on page 3-4 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door or the liftgate/
boot lid.
 


 Opening the bonnet.



 Switching the ignition ON.



(With the advanced keyless
function)
  Pressing the electric liftgate/boot
lid opener while the key is being
carried.
  To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
fl ash once to indicate that the system
is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Switching the ignition ON.



(With the advanced keyless function)
 Pressing a request switch on the doors.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop an Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
(With the advanced keyless function)
 


 Pressing a request switch on the doors.



 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
.B[EB@&'&&"@&EJUJPOJOEC







3–56
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, fl ares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
 


 Have the proper ratio of antifreeze in the
radiator.
  Refer to Engine Coolant on page 6-30 .



 Inspect the battery and its leads. Cold
reduces battery capacity.
 


 Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).
 


 Inspect the ignition system for damage
and loose connections.
 


 Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-34 ).
NOTE

 Do not use the parking brake in
freezing weather as it may freeze.
Instead, shift to P with an automatic
transaxle and to 1 or R with a manual
transaxle. Block the rear wheels.
  Remove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
  Do not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
.B[EB@&'&&"@&EJUJPOJOEC







3–57
Before Driving
Driving Tips
NOTE
  Never use warm or hot water for
removing snow or ice from windows
and mirrors as it could result in the
glass cracking.
  Drive slowly. Braking performance
can be adversely affected if
snow or ice adheres to the brake
components. If this situation occurs,
drive the vehicle slowly, releasing
the accelerator pedal and lightly
applying the brakes several times
until the brake performance returns
to normal.
Snow Tyres
WARNING
Use only the same size and type tyres
(snow, radial, or non-radial) on all four
wheels:
Using tyres different in size or type is
dangerous. Your vehicle's handling
could be greatly affected and result in
an accident.
CAUTION
Check local regulations before using
studded tyres.
Use snow tyres on all four wheels
Do not exceed the maximum permissible
speed for your snow tyres or legal speed
limits.
Europe
When snow tyres are used, select the
specifi ed size and pressure (page 9-13 ).
Tyre Chains
Check local regulations before using tyre
chains.
CAUTION
  Chains may affect handling. 
 Do not go faster than 50 km/h (30
mph) or the chain manufacturer's
recommended limit, whichever is
lower.
  Drive carefully and avoid bumps,
holes, and sharp turns.
  Avoid locked-wheel braking. 
 Do not use chains on a temporary
spare tyre; it may result in damage to
the vehicle and to the tyre.
  Do not use chains on roads that are
free of snow or ice. The tyres and
chains could be damaged.
  Chains may scratch or chip
aluminium wheels.
.B[EB@&'&&"@&EJUJPOJOEC







3–59
Before Driving
Driving Tips
Driving In Flooded Area
WARNING
Dry off brakes that have become
wet by driving slowly, releasing the
accelerator pedal and lightly applying
the brakes several times until the brake
performance returns to normal:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been affected.
CAUTION
Do not drive the vehicle on fl ooded
roads as it could cause short circuiting
of electrical/electronic parts, or
engine damage or stalling from water
absorption. If the vehicle has been
immersed in water, consult an expert
repairer, we recommend an Authorised
Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







3–69
Before Driving
Towing
Safety Chains
Safety chains must be used as a precautionary measure should the trailer become
unintentionally unhitched. They should cross under the trailer tongue and attach to the hitch.
Leave enough slack to allow full turns. Consult literature published by your trailer or hitch
manufacturer for more details.
WARNING
Make sure the safety chain is securely attached to both the trailer and the vehicle prior
to departure:
Towing a trailer without using a safety chain securely attached to both the trailer and
the vehicle is dangerous. If damage occurs to the coupling unit or hitch ball, the trailer
could wander into another lane and cause a collision.
Trailer Lights
CAUTION
Do not connect a trailer lighting system directly to the lighting system of your Mazda.
This may damage your vehicle's electrical system and lighting systems. To connect the
lighting system, consult an Authorised Mazda Dealer.
Trailer Brakes
Check the Maximum trailer towing-load table in Weight Limits (page 3-61 ), and if your
trailer weight exceeds the value in the TOTAL TRAILER WEIGHT (Trailer without brake),
trailer brakes are required.
If your trailer has brakes, make sure they meet regulations.
WARNING
Do not connect a hydraulic trailer-brake system to your vehicle's brake system:
Connecting a hydraulic trailer-brake system directly to the vehicle brake system is
dangerous and will result in inadequate braking and possible injury.
.B[EB@&'&&"@&EJUJPOJOEC