warning lights MAZDA MODEL 3 HATCHBACK 2015 (in English) Service Manual

4–121
When Driving
i-ACTIVSENSE
Indication on Display
The Distance Recognition Support System (DRSS) operation status is indicated in the active
driving display. Regarding malfunctions, check the vehicle conditions or have it inspected
by an expert repairer, we recommend an Authorised Mazda Repairer according to the
content of the displayed message.
Refer to Warning/Indicator Lights on page 4-40 .
NOTE
  When the ignition is switched off, the operation status before the system was turned
off is maintained. For example, if the ignition is switched off with the Distance
Recognition Support System (DRSS) operable, the system will be operable when the
ignition is switched ON the next time.
  The Distance Recognition Support System (DRSS) can be turned on/off and the
system's sensitivity can be changed.
 Refer to Personalisation Features on page 9-16 .
Vehicle ahead
display
Distance between
vehicle display
.B[EB@&'&&"@&EJUJPOJOEC







4–126
When Driving
i-ACTIVSENSE
NOTE
  During headway control travel, the system accelerates and decelerates your vehicle
in conjunction with the speed of the vehicle ahead. However, if it is necessary to
accelerate for a lane change or if the vehicle ahead brakes suddenly causing you to
close in on the vehicle rapidly, accelerate using the accelerator pedal or decelerate
using the brake pedal depending on the conditions.
  While the Mazda Radar Cruise Control (MRCC) system is in use, it does not cancel
even if the selector lever (automatic transaxle)/shift lever (manual transaxle) is
operated and any intended engine braking will not occur. If deceleration is required,
lower the vehicle speed setting or depress the brake pedal.
  The brake lights are illuminated while the Mazda Radar Cruise Control (MRCC)
automatic braking is operating, however, they may not be illuminated while the
vehicle is on a down slope at the set vehicle speed or travelling at a constant speed and
following a vehicle ahead.
  The Mazda Radar Cruise Control (MRCC) warning light (amber) fl ashes when the
system has a malfunction.
 Refer to Warning Lights on page 4-41 .
Mazda Radar Cruise Control (MRCC) Display Indication
The setting status and operation conditions of the Mazda Radar Cruise Control (MRCC)
system are indicated in the active driving display.
Vehicle ahead display
MRCC Distance between vehicle display
MRCC Set vehicle
speed
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–14 3
When Driving
i-ACTIVSENSE
NOTE
  In the following cases, the laser sensor (front) may inadvertently determine that there
is a vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


 Objects on the road at the entrance to a curve.



 Vehicles passing in the opposite lane while making a curve.



 Metal objects, bumps, or protruding objects on the road.



 When passing through a toll gate.



 When passing under a vinyl curtain or fl ag.



 Plastic objects such as pylons.



 Two-wheeled vehicles, pedestrians, animals or standing trees.



 Vehicle is driven with some of the tyres having signifi cant wear. 

 When the system operates, the user is notifi ed by the fl ashing Smart City Brake
Support (SCBS) indicator light (red) and the active driving display * .   The Smart City Brake Support (SCBS) warning light (amber) turns on when the
system has a malfunction.
 Refer to Warning Lights on page 4-41 .
.B[EB@&'&&"@&EJUJPOJOEC







4–14 6
When Driving
i-ACTIVSENSE
NOTE
  The Smart Brake Support (SBS) system operates when all of the following conditions
are met:
 


 The ignition is switched ON.



 The Smart Brake Support (SBS) system is on.



 The DSC OFF indicator light is not illuminated.



 The vehicle speed is about 15 km/h or faster (10 mph or faster).



 The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


 The Dynamic Stability Control (DSC) is not operating. 

 The Smart Brake Support (SBS) system may not operate under the following
conditions:
 


 If there is the possibility of hitting only a part of a vehicle ahead.



 If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



 The vehicle is driven at the same speed as the vehicle ahead.



 The accelerator pedal is depressed.



 The brake pedal is depressed.



 The steering wheel is being operated.



 The selector lever is being operated.



 The direction indicator is being used. 

 Although the objects which activate the system are 4-wheeled vehicles, the radar
sensor could detect the following objects, determine them to be an obstruction, and
operate the Smart Brake Support (SBS) system.
 


 Objects on the road at the entrance to a curve (including guardrails and snow banks).



 A vehicle appears in the opposite lane while cornering or rounding a curve.



 When crossing a narrow bridge.



 When passing under a low gate or through a tunnel or narrow gate.



 When entering an underground parking area.



 Metal objects, bumps, or protruding objects on the road.



 If you suddenly come close to a vehicle ahead.



 When driving in areas where there is high grass or forage.



 Two-wheeled vehicles such as motorbikes or bicycles.



 Pedestrians or non-metallic objects such as standing trees. 

 When the system operates, the user is notifi ed by the fl ashing Smart Brake Support
(SBS) indicator light (red) and the active driving display.
  The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction.
 Refer to Warning Lights on page 4-41 .
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–161
When Driving
Tyre Pressure Monitoring System
Tyre Pressure Monitoring System *
The Tyre Pressure Monitoring System (TPMS) monitors the air pressure of all four tyres. If
the air pressure of one or more tyres is too low, the system warns the driver by indicating the
tyre pressure monitoring system warning light in the instrument cluster and operating a beep
sound. The system monitors the tyre pressures indirectly using the data sent from the ABS
wheel speed sensors.
To allow the system to operate correctly, the system needs to be initialized with the specifi ed
tyre pressure (value on the tyre pressure label). Follow the procedure and perform the
initialization.
Refer to Tyre Pressure Monitoring System Initialization on page 4-164 .
The warning light fl ashes when the system has a malfunction.
Refer to Warning Lights on page 4-41 .
ABS wheel speed sensor
.B[EB@&'&&"@&EJUJPOJOEC







6–52
Maintenance and Care
Owner Maintenance
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer when the replacement is
necessary.
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the fl ying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights (With xenon fusion
headlights)
Low/High beam bulbs
You cannot replace the low/high beam
bulbs by yourself. The bulbs must
be replaced at an expert repairer, we
recommend an Authorised Mazda
Repairer.
Headlights (With halogen headlights)
Low-beam bulbs
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the headlight switch is off.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–68
Maintenance and Care
Owner Maintenance
Fuse Panel Description
Fuse block (Engine compartment)
Multiplex slow blow fuse
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 FOG 15 A Front fog lights
*
2 H/L HI 20 A Headlight high beam
3 H/CLEAN 20 A Headlight washer *
4 STOP 10 A Brake lights, Rear fog light *
5 ROOM 15 A Overhead light
6
7.5 A Engine control system *
7 FUEL WARM 15 A Fuel warmer *
8 HAZARD 25 A Hazard warning fl ashers, Direction indicator lights
9 ABS/DSCS 30 A ABS, Dynamic stability control system *
10 METER2 7.5 A Instrument cluster *
11 AUDIO2 7.5 A Audio system *
12 BOSE 25 A Bose ® Sound System-equipped model *
13 AUDIO1 15 A Audio system *
14 FUEL PUMP 15 A Fuel system *
15 HID R
D R L 15 A Headlight (RH) *1
16 AT PUMP 15 A Transaxle control system *
17 HORN 15 A Horn
18 TAIL 15 A Tail lights, Number plate lights, Position lights
.B[EB@&'&&"@&EJUJPOJOEC







6–77
Maintenance and Care
Appearance Care
Plastic Part Maintenance
 












 When cleaning the plastic lenses of
the lights, do not use petrol, paraffi n,
rectifi ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signifi cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, fl ush with water
immediately.
 


 If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fl uids such as petrol,
oil, engine coolant, or battery fl uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or fl uids using a soft
cloth immediately.
 


 High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
 


 Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
 


 In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
Interior Care
WARNING
Do not spray water in the cabin:
Splashing water on electrical parts
such as the audio unit and switches
is dangerous as it could cause a
malfunction or a fi re.
Instrument panel Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
instrument panel. They will damage and
discolour the instrument panel. If these
solutions get on the instrument panel, wipe
them off immediately.
CAUTION
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discolouration,
wrinkling, cracks and peeling.
Instrument panel top (soft pad)
 




 Extremely soft material is used for the
soft pad surface. When cleaning, it is
recommended that you use a clean towel
dampened in a mild detergent to remove
soiling.
 


 If the soft pad surface is rubbed harshly,
it could result in the surface being
damaged leaving white scratch marks.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.



Parking in an Emergency ................... 7-2
Parking in an Emergency ............... 7-2
Roadside Emergency Triangle
Retaining Strap
* ............................. 7-2
Flat Tyre ............................................... 7-3
Spare Tyre and Tool Storage .......... 7-3
Emergency Flat Tyre Repair Kit* ........ 7-8
Changing a Flat Tyre (With spare
tyre) .............................................. 7-15
Battery Runs Out .............................. 7-21
Jump-Starting ............................... 7-21
Emergency Starting .......................... 7-24
Starting a Flooded Engine (MZR 1.6,
SKYACTIV-G 1.5 and SKYACTIV-G
2.0) ............................................... 7-24
Push-Starting ................................ 7-24
Running Out of Fuel (SKYACTIV-D
2.2) ............................................... 7-25
Overheating ....................................... 7-26
Overheating .................................. 7-26
Emergency Towing ............................ 7-28
Towing Description ...................... 7-28
Towing Hooks .............................. 7-29 Warning/Indicator Lights and Warning
Sounds ................................................ 7-32
If a Warning Light Turns On or
Flashes .......................................... 7-32
Message Indicated in Multi-
information Display ..................... 7-45
Message Indicated on Display* ...... 7-47
Warning Sound is Activated ......... 7-49
When Liftgate/Boot Lid Cannot be
Opened ............................................... 7-54
When Liftgate/Boot Lid Cannot be
Opened ......................................... 7-54
Active Driving Display Does Not
Operate ............................................... 7-56
If the Active Driving Display does not
operate .......................................... 7-56
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–2
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traffi c hazard
and that they must take extreme caution
when near it.

Depress the hazard warning fl asher and
all the direction indicators will fl ash. The
hazard warning indicator lights in the
instrument cluster fl ash simultaneously.
NOTE

 The direction indicators do not work
when the hazard warning lights are
on.
  Check local regulations about the use
of hazard warning lights while the
vehicle is being towed to verify that
it is not in violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
Keep the roadside emergency triangle in
the right side trim and secure it with the
strap.
Saloon
Strap
Hatchback
Strap
.B[EB@&'&&"@&EJUJPOJOEC