reset MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

Page 117 of 689

3–39
Before Driving
Windows
Auto-opening/closing
To fully open the window automatically,
press the switch completely down, then
release. The window will fully open
automatically.
To fully close the window automatically,
pull the switch completely up, then
release. The window will fully close
automatically.
To stop the window partway, pull or press
the switch in the opposite direction and
then release it.
Power window system initialization
procedure
If the battery was disconnected during
vehicle maintenance, or for other reasons
(such as a switch continues to be operated
after the window is fully open/closed),
the window will not fully open and close
automatically.
The power window auto function will only
resume on a power window that has been
reset.
1. Switch the ignition ON.
2. Make sure that the power window lock
switch located on the driver's door is
not depressed.
3. Press the switch and fully open the
window.
4. Pull up the switch to fully close the
window and continue holding the
switch for about 2 seconds after the
window fully closed. Jam-safe window
If a person's hands, head or an object
blocks the window during the auto-closing
operation, the window will stop and open
halfway.
WARNING
Make sure nothing blocks the window
just before it reaches the fully closed
position or while holding up the power
window switch:
Blocking the power window just before
it reaches the fully closed position or
while holding up the power window
switch is dangerous.
In this case, the jam-safe function
cannot prevent the window from
closing all the way. If fi ngers are
caught, serious injuries could occur.
NOTE
  Depending on driving conditions, a
closing power window could stop
and start opening when the window
feels a shock that is similar to
something blocking it.
 In the event the jam-safe function
activates and the power window
cannot be closed automatically, pull
and hold the switch and the window
will close.
  The jam-safe window function does
not operate until the system has been
reset.
.B[EB@&'&&"@&EJUJPOJOEC

Page 120 of 689

3–42
Before Driving
Windows
NOTE
Before washing your Mazda, make sure
the sunroof is completely closed so that
water does not get inside the cabin area.
After washing your Mazda or after it
rains, wipe the water off the sunroof
before operating it to avoid water
penetration which could cause rust and
water damage to your headliner.
Tilt Operation
The rear of the sunroof can be tilted open
to provide more ventilation.
To fully tilt automatically, momentarily
press the tilt/slide switch.
To stop tilting partway, press the tilt/slide
switch.
To close to the desired position, press the
tilt/slide switch in the forward direction.
Close (Tilt down)
Tilt up
Slide Operation
To fully open automatically, momentarily
press the tilt/slide switch in the backward
direction.
To stop sliding partway, press the tilt/slide
switch.
To close to the desired position, press the
tilt/slide switch in the forward direction.
CloseOpen
Power Sunroof Reset Procedure
If the battery is disconnected, the sunroof
will not operate. The sunroof will not
operate correctly until it is reset. Carry
out the following procedure to reset the
sunroof and resume operation:
1. Switch the ignition ON.
2. Press the tilt switch, to partially tilt
open the rear of the sunroof.
3. Repeat Step 2. The rear of the sunroof
tilts open to the fully open position,
then closes a little.
NOTE
If the reset procedure is performed
while the sunroof is in the slide position
(partially open) it will close before the
rear tilt opens.
.B[EB@&'&&"@&EJUJPOJOEC

Page 123 of 689

3–45
Before Driving
Security System
NOTE
  The keys carry a unique electronic
code. For this reason, and to assure
your safety, obtaining a replacement
key requires some waiting time.
They are only available through an
Authorised Mazda Repairer.
  Always keep a spare key in case one
is lost. If a key is lost, consult an
Authorised Mazda Repairer as soon
as possible.
  If you lose a key, an Authorised
Mazda Repairer will reset the
electronic codes of your remaining
keys and immobilizer system.
Bring all the remaining keys to an
Authorised Mazda Repairer to reset.
 Starting the vehicle with a key that
has not been reset is not possible.
Operation
NOTE
  The engine may not start and security
indicator light may illuminate or
fl ash if the key is placed in an area
where it is diffi cult for the system
to detect the signal, such as on the
instrument panel or in the glove
compartment. Move the key to a
location within the signal range,
switch the ignition off, and then
restart the engine.
  Signals from a TV or radio station,
or from a transceiver or mobile
telephone could interfere with your
immobilizer system. If you are using
the proper key and the engine fails
to start, check the security indicator
light.
Arming
The system is armed when the ignition is
switched from ON to off.
The security indicator light in the
instrument cluster fl ashes every 2 seconds
until the system is disarmed.
Disarming
The system is disarmed when the
ignition is switched ON with the correct
programmed key. The security indicator
light illuminates for about 3 seconds and
then turns off. If the engine does not start
with the correct key, and the security
indicator light remains illuminated or
fl ashing, try the following:
Make sure the key is within the
operational range for signal transmission.
Switch the ignition off, and then restart
the engine. If the engine does not start
after 3 or more tries, contact an Authorised
Mazda Repairer.
NOTE
  If the security indicator light fl ashes
continuously while you are driving,
do not shut off the engine. Go to an
Authorised Mazda Repairer and have
it checked. If the engine is shut off
while the indicator light is fl ashing,
you will not be able to restart it.
  Because the electronic codes are
reset when the immobilizer system
is repaired, the keys are needed.
Make sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
.B[EB@&'&&"@&EJUJPOJOEC

Page 169 of 689

4–19
When Driving
Start/Stop Engine
NOTE
  If any one of the following occurs, the length of time the engine is stopped
automatically could be shorter or the length of time required before i-stop functions
again could be longer.
 


 The ambient temperature is high or low.



 The battery power is depleted.



 The power consumption of vehicle equipment is high. 

 The i-stop function does not operate when the ambient temperature is extremely high
or low.
  The engine may not stop automatically for a while after the battery leads are
reconnected after temporarily disconnecting them. In addition, if the battery is
replaced, the i-stop system will need to be reset and checked to make sure it operates
correctly. When replacing the battery, consult an expert repairer, we recommend an
Authorised Mazda Repairer.
i-stop OFF Switch
The i-stop function can be turned off by
pressing the switch until the beep sounds
and the i-stop warning light (amber) in the
instrument cluster illuminates. The i-stop
function can be turned back on by pressing
the switch again until the beep sounds and
the i-stop warning light (amber) turns off.
NOTE
If the i-stop function was turned off
using the i-stop OFF switch, the system
will resume operation the next time the
engine is started.
.B[EB@&'&&"@&EJUJPOJOEC

Page 176 of 689

4–26
When Driving
Instrument Cluster and Display
NOTE
When the ignition is switched to ACC
or off, the odometer or trip meters
cannot be displayed, however, pressing
the selector can inadvertently switch
the trip meters or reset them during an
approximate ten-minute period in the
following cases:
 
 After the ignition is switched to off
from ON.
  After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is fi lled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed. The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
NOTE
 (Vehicles with type C/type D audio) If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
 Refer to Fuel Economy Monitor on
page 4-94 .
  Only the trip meters record tenths of
kilometres (miles).
  The trip record will be erased when:




 The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


 The vehicle is driven over 9999.9
km (mile).
.B[EB@&'&&"@&EJUJPOJOEC

Page 179 of 689

*Some models.4–29
When Driving
Instrument Cluster and Display
NOTE

 When the illumination dimmer is
cancelled, the instrument cluster
cannot be dimmed even if the light
switch is turned to the
or
position.  When the illumination dimmer is
cancelled, the screen in the centre
display switches to constant display
of the daytime screen.
Outside Temperature Display
(Without Multi-information
display)
*
When the ignition is switched ON, the
outside temperature is displayed.
NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and
vehicle conditions:
 


 Signifi cantly cold or hot
temperatures.
 


 Sudden changes in outside
temperature.
 


 The vehicle is parked.



 The vehicle is driven at low
speeds. The outside temperature unit can be
switched between Celsius and Fahrenheit
using the following procedure.
1. Press the INFO button with the ignition
switched off and continue pressing the
INFO button for 5 seconds or longer
while switching the ignition ON. The
outside temperature display fl ashes.
2. Press the up
or down part of the
INFO switch to change the outside
temperature unit.
3. Press and hold the INFO button for 3
seconds or longer while the outside
temperature display is fl ashing. The
outside temperature display illuminates.
Cruise Control Set Vehicle Speed
Display (Without Multi-
information display)
*
The vehicle speed preset using the cruise
control is displayed.
.B[EB@&'&&"@&EJUJPOJOEC

Page 180 of 689

*Some models.4–30
When Driving
Instrument Cluster and Display
Trip Computer and INFO Switch *
The following information can be selected
by pressing the up
or down part of the
INFO switch with the ignition switched
ON.
 


 Approximate distance you can travel on
the available fuel
 


 Average fuel economy



 Current fuel economy



 Average vehicle speed



 Vehicle speed alarm *
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
(European model)
(Except European model)
NOTE
  Even though the distance-to-empty
display may indicate a suffi cient
amount of remaining driving distance
before refuelling is required, refuel
as soon as possible if the fuel level
is very low or the low fuel warning
light illuminates.
  The display may not change unless
you add more than approximately 9 L
(2.3 US gal, 1.9 Imp gal) of fuel.
  The distance-to-empty is the
approximate remaining distance
the vehicle can be driven until all
the graduation marks in the fuel
gauge (indicating the remaining fuel
supply) disappear.
Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total travelled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed every
minute.
(European model)
(Except European model)
To clear the data being displayed, press the
INFO button for more than 1.5 seconds.
After pressing the INFO button, - - - L/100
km (- - - mpg) will be displayed for about
1 minute before the fuel economy is
recalculated and displayed.
.B[EB@&'&&"@&EJUJPOJOEC

Page 181 of 689

*Some models.4–31
When Driving
Instrument Cluster and Display
Current fuel economy mode
This mode displays the current fuel
economy by calculating the amount of fuel
consumption and the distance travelled.
Current fuel economy will be calculated
and displayed every 2 seconds.
(European model)
(Except European model)
When you've slowed to about 5 km/h (3
mph), - - - L/100 km (- - - mpg) will be
displayed.
Average vehicle speed mode
This mode displays the average vehicle
speed by calculating the distance and the
time travelled since connecting the battery
or resetting the data.
Average vehicle speed will be calculated
and displayed every 10 seconds.
(European model)
(Except European model)
To clear the data being displayed, press the
INFO button for more than 1.5 seconds.
After pressing the INFO button, - - - km/h
(- - - mph) will be displayed for about
1 minute before the vehicle speed is
recalculated and displayed.
Vehicle speed alarm mode *
In this mode, the current setting for the
vehicle speed alarm is displayed. You can
change the vehicle speed setting at which
the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep
sound is heard. The set vehicle speed
fl ashes several times.
The vehicle speed alarm can be set using
the INFO switch.
NOTE
  Always set the vehicle speed
according to the laws and regulations
of the country/city in which the
vehicle is driven. In addition, always
verify the speed of the vehicle using
the speedometer.
  The vehicle speed alarm function can
be set between 30 and 250 km/h (20
and 150 mph).
The vehicle speed alarm can be set using
the following procedure.
1. Press the INFO switch on the speed
alarm screen.
2. Select ON and press the INFO switch.
3. Set the vehicle speed by pressing the
INFO up or down button, and then
press the INFO button.
.B[EB@&'&&"@&EJUJPOJOEC

Page 184 of 689

*Some models.4–34
When Driving
Instrument Cluster and Display
Outside Temperature Warning *
When the outside temperature is low, the
indication fl ashes and a beep sound is
heard to warn the driver of the possibility
of icy roads.
If the outside temperature is lower than
about 4 °C, the outside temperature
display and the
mark fl ashes for about
ten seconds and a beep sound is heard
once.
NOTE
If the outside temperature is lower than
-20 °C, the beep sound does not operate.
However, the
mark illuminates.
Cruise Control Set Vehicle Speed
Display
The vehicle speed preset using the cruise
control is displayed.
.B[EB@&'&&"@&EJUJPOJOEC

Page 185 of 689

4–35
When Driving
Instrument Cluster and Display
Distance-to-empty Mode
This mode displays the approximate distance you can travel on the remaining fuel based on
the fuel economy.
The distance-to-empty will be calculated and displayed every second.
NOTE
  Even though the distance-to-empty display may indicate a suffi cient amount of
remaining driving distance before refuelling is required , refuel as soon as possible if
the fuel level is very low or the low fuel warning light illuminates.
  The display will not change unless you add more than approximately 9 L (2.3 US gal,
1.9 Imp gal) of fuel.
  The distance-to-empty is the approximate remaining distance the vehicle can be driven
until all the graduation marks in the fuel gauge indicating the remaining fuel supply
disappear.
Average Fuel Economy Mode
This mode displays the average fuel economy by calculating the total fuel consumption
and the total travelled distance since purchasing the vehicle, re-connecting the battery after
disconnection, or resetting the data.
The average fuel economy is calculated and displayed every minute.
To clear the data being displayed, press the INFO button for more than 1.5 seconds. After
pressing the INFO button, - - - L/100 km (- - - mpg) will be displayed for about 1 minute
before the fuel economy is recalculated and displayed.
.B[EB@&'&&"@&EJUJPOJOEC

Page:   1-10 11-20 21-30 31-40 41-50 ... 50 next >