clock MAZDA MODEL 6 2004 (in English) User Guide

6-55
Interior Comfort
Interior Equipment
Form No. 8R29-EA-02I
5. Pass the plug cord through the hole of
the tray and insert the plug in the
socket.
6. Make sure the plug cord is running
through the cap slot; reinstall the cap
and turn it clockwise (about 45°
to the
opened position).7. Set the plug cord into the slit of the tray
mat and replace the tray mat.
Plug
Plug cord
shuseizumi_J56J_8R29_EA_02I.book Page 55 Saturday, September 7, 2002 12:58 PM

7-4
In Case of an Emergency
Flat Tire
Form No. 8R29-EA-02I

Jack
To remove the jack
1. Remove the jack container lid.
2. Turn the wing bolt counterclockwise.
To secure the jack
Perform the removal procedure in reverse.

Spare Tire
Your Mazda has a temporary spare tire.
The temporary spare is lighter and smaller
than a conventional tire, and is designed
only for emergency use and should be
used only for VERY short periods.
Temporary spares should NEVER be used
for long drives or extended periods.
Jack
Wing bolt
Driving with a Temporary Spare Tire on Ice or Snow:Driving with a spare tire on the front
(driving) wheels on ice or snow is
dangerous. Handling will be affected.
You could lose control of the vehicle
and have an accident. Put the spare
tire on the rear axle and move a
regular tire to the front.
To avoid damage to the temporary
spare or to the vehicle, observe the
following precautions:
•
Don’t exceed 80 km/h (50 mph).
•
Avoid driving over obstacles. Also,
don’t drive through an automatic car
wash. This tire’s diameter is smaller
than a conventional tire, so the
ground clearance is reduced about
43 mm (1.7 in).
•
Don’t use a tire chain on this tire
because it won’t fit properly.
•
Don’t use your temporary spare on
any other vehicle, it has been
designed only for your Mazda.
•
Use only one temporary spare tire
on your vehicle at the same time.
WARNING
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 4 Saturday, September 7, 2002 12:58 PM

7-5
In Case of an Emergency
Flat Tire
Form No. 8R29-EA-02I
To remove the spare tire
1. Remove the trunk board.
2. Turn the tire hold-down bolt
counterclockwise.
To secure the spare tire
Perform the removal procedure in reverse.If you have a flat tire, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tire.
Stopping in traffic or on the shoulder of a
busy road is dangerous.
Trunk board
Lug wrench
Changing a Flat Tire
NOTE
If the following occurs while driving, it
could indicate a flat tire.
•
Steering becomes difficult.
•
The vehicle begins to vibrate
excessively.
•
The vehicle pulls in one direction.
Jacking a Vehicle:Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a
jack.
Passenger in Vehicle Supported by a
Jack:Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury. Never allow anyone inside a
vehicle supported by a jack.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 5 Saturday, September 7, 2002 12:58 PM

7-7
In Case of an Emergency
Flat Tire
Form No. 8R29-EA-02I
2. Loosen the lug nuts by turning them
counterclockwise one turn each, but
don’t remove any until the tire has been
raised off the ground.
3. Place the jack under the jacking
position closest to the tire being
changed.
4. Insert the lug wrench into the jack.
Jacking position
Incorrect Jacking Position:Attempting to jack the vehicle in
positions other than those
recommended in this manual is
dangerous. The vehicle could slip off
the jack and seriously injure or even
kill someone. Use only the front and
rear jacking positions recommended
in this manual.
Improper Jack:
Using a jack that isn’t designed for
your Mazda is dangerous. The vehicle
could slip off the jack and seriously
injure someone. Use only the jack
provided with your Mazda.
Placing Objects Under the Jack:
Jacking the vehicle with an object
under the jack is dangerous. The jack
could slip and someone could be
seriously injured by the jack or the
falling vehicle. Never place objects
under the jack.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 7 Saturday, September 7, 2002 12:58 PM

7-8
In Case of an Emergency
Flat Tire
Form No. 8R29-EA-02I
5. Turn the lug wrench clockwise and
raise the vehicle high enough so that
the spare tire can be installed. Before
removing the lug nuts, make sure your
Mazda is firmly in position and that it
cannot slip or move.
6. Remove the lug nuts by turning them
counterclockwise; then remove the
wheel.
Locking Lug Nuts
If your vehicle has optional antitheft
wheel lug nuts, one on each wheel will
lock the tires and you must use a special
key to unlock them. This key is attached
to the lug wrench and is stored with the
spare tire. Register them with the lock
manufacturer by filling out the card
provided in the glove box and mailing it in
the accompanying envelope. If you lose
your key, consult an Authorized Mazda
Dealer or use the lock manufacturer’s
order form, which is with the registration
card.
To remove an antitheft lug nut
1. Get the key for the locking lug nut.
2. Place it on top of the nut, and be sure to
hold the key square to it. If you hold
the key at an angle, you may damage
both key and nut. Don’t use a power
impact wrench.
3. Place the lug wrench on top of the key
and apply pressure. Turn the wrench
counterclockwise.
To replace the nut
1. Place the key on top of the nut.
2. Place the lug wrench on top of the key,
apply pressure, and turn it clockwise.
Antitheft lug nutSpecial key
shuseizumi_J56J_8R29_EA_02I.book Page 8 Saturday, September 7, 2002 12:58 PM

7-10
In Case of an Emergency
Flat Tire
Form No. 8R29-EA-02I
4. Turn the lug wrench counterclockwise
and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
If you’re unsure of how tight the nuts
should be, have them inspected at a
service station.
Nut tightening torque:

N·m (kgf·m, ft·lbf) 88—118 (9—12, 65—87)
Loose Lug Nuts:Improperly or loosely tightened lug
nuts are dangerous. The wheel could
wobble or come off. This could result
in loss of vehicle control and cause a
serious accident. Always securely and
correctly tighten the lug nuts.
Metric Studs and Lug Nuts:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip
off and cause an accident. Be sure to
reinstall the same nuts you removed
or replace them with metric nuts of
the same configuration.
Incorrect Tire Air Pressure:
Driving on tires with incorrect air
pressure is dangerous. Tires with
incorrect pressure could affect
handling and result in an accident.
Don’t drive with any tires that have
incorrect air pressure. When you
check the regular tires’ air pressure,
check the spare tire, too.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 10 Saturday, September 7, 2002 12:58 PM

8-14
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I

Changing Coolant
Change coolant according to Scheduled
Maintenance (page 8-3).
For mixture percentage:To change coolant
1. Remove the cooling system cap. •
Use only soft (demineralized) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant’s effectiveness.
•
Don’t add only water. Always add a
proper coolant mixture.
•
The engine has aluminum parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
•
DO NOT USE alcohol or methanol
antifreeze. DO NOT MIX alcohol
or methanol with the coolant. This
could damage the cooling system.
•
Don’t use a solution that contains
more than 60 % antifreeze.
This would reduce effectiveness.
ProtectionVo l u m e
Antifreeze
solutionWa t e r
Above
−16
°C (3
°F) 35% 65%
Above
−26
°C (
−15
°F) 45% 55%
Above
−40
°C (
−40
°F) 55% 45%
CAUTIONRemoving the Cooling System Cap:Removing the cooling system cap or
drain plug while the engine is
running or hot is dangerous. This
might lead to cooling system and
engine damage and could result in
serious injury from escaping hot
coolant or steam. Turn off the engine
and wait until it’s cool. Even then, be
very careful when removing the cap
or drain plug. Wrap a thick cloth
around it and slowly turn it
counterclockwise to the first stop.
Step back while the pressure escapes.
When you’re sure all the pressure is
gone, press down on the cap — still
using a cloth — turn the cap, and
remove it.
WARNING
Loosen
Tighten
Loosen Tighten 2.3-liter engine
shuseizumi_J56J_8R29_EA_02I.book Page 14 Saturday, September 7, 2002 12:58 PM