Lock MAZDA MODEL 6 2004 (in English) Workshop Manual

5-10
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I
3.0-liter engine
For normal acceleration, we recommend
these shift points.
For cruising
Downshifting
When you must slow down in heavy
traffic or on a steep upgrade
, downshift
before the engine starts to overwork. This
reduces the chance of stalling and gives
better acceleration when you need more
speed.
On a steep downgrade, downshifting helps
maintain safe speed and prolongs brake
life.
Various Lockouts:
1 to 2 27 km/h (17 mph)
2 to 3 48 km/h (30 mph)
3 to 4 56 km/h (35 mph)
4 to 5 63 km/h (39 mph)
1 to 2 13 km/h (8 mph)
2 to 3 34 km/h (21 mph)
3 to 4 52 km/h (32 mph)
4 to 5 66 km/h (41 mph)
Automatic Transaxle
Controls
Indicates that you must
depress the brake pedal to
shift (The ignition switch
must be in the ACC or ON
position).
Indicates the shift lever can
be shifted freely into any
position.
shuseizumi_J56J_8R29_EA_02I.book Page 10 Saturday, September 7, 2002 12:58 PM

5-11
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Transaxle Ranges
The shift lever must be in P or N to
operate the starter.
P (Park)
P locks the transaxle and prevents the
front wheels from rotating.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete stop
before shifting to or from R, except as
explained under Rocking the Vehicle
(page 4-7).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.D (Drive)
D is the normal driving position. From a
stop, the transaxle will automatically shift
through a 4-gear/5-gear
* sequence.*3.0-liter engine model
M (Manual)
M is the manual shift mode position.
Gears can be shifted up or down by
tapping the shift lever back or forward
from this position.
Holding the Vehicle with P:Setting the shift lever to the P position
without using the parking brake to
hold the vehicle is dangerous. If P
fails to hold, the vehicle could move
and cause an accident. To hold the
vehicle, set the shift lever to P AND
set the parking brake.
•
Shifting into P, N or R while the
vehicle is moving can damage your
transaxle.
•
Shifting into a driving gear or
reverse when the engine is running
faster than idle can damage the
transaxle.
WARNING
CAUTION
Shifting from N or P:It’s dangerous to shift from N or P
into a driving gear when the engine is
running faster than idle. If this is
done, the vehicle could move
suddenly, causing an accident or
serious injury. If the engine is
running faster than idle, don’t shift
from N or P into a driving gear.
Shifting into N while Driving:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which
could lead to an accident or serious
injury. Do not shift into N when
driving the vehicle.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 11 Saturday, September 7, 2002 12:58 PM

5-12
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Shift-Lock System
The shift-lock system prevents shifting
out of P unless the brake pedal is
depressed.

To shift from P:
1. Depress and hold the brake pedal.
2. Start the engine.
3. Move the shift lever.

Manual Shift Mode
This mode gives you the feel of driving a
manual transaxle vehicle by tapping the
shift lever forward and back while in this
mode.
To change to manual shift mode, shift the
lever from D to M.To return to automatic shift mode, shift
the lever from M to D.

Indicators
Shift position indicator
In manual shift mode, the "M" of the shift
position indicator in the instrument panel
illuminates.
Gear position indicator
In manual shift mode, the numeral for the
selected gear illuminates below the shift
position indicator.
NOTE
•
When the ignition switch is in the
LOCK position, the transaxle
cannot be shifted from P.
•
To be sure the vehicle is in park,
the ignition key cannot be
removed unless the shift lever is in
P.
NOTE
•
If you change to manual shift mode
when the vehicle is stopped, the
gear will shift to M1.
•
If you tap the shift lever back when
the vehicle is stopped and the gear
is at M1, the gear will shift to M2.
M2 is helpful for starting on
slippery surfaces.
Shift position
indicator
Gear position
indicator
shuseizumi_J56J_8R29_EA_02I.book Page 12 Saturday, September 7, 2002 12:58 PM

5-24
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8R29-EA-02I

Speedometer
The speedometer indicates the speed of
the vehicle.

Odometer and Trip Meter
The display mode can be changed
between trip meter A and trip meter B by
pressing the selector while they are
displayed. The selected mode will be
displayed.
Odometer
The odometer records the total distance
the vehicle has been driven.
Tr i p m e t e r
The trip meter can record the total
distance of two trips. One is recorded in
trip meter A, and the other is recorded in
trip meter B.
For instance, trip meter A can record the
distance from the point of origin, and trip
meter B can record the distance from
where the fuel tank is filled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
Selector
Odometer
Trip meter
Odometer
Odometer Trip meter A
Press the selector
Press the selector Trip meter B
NOTE
(Standard meter)

The odometer and trip meter can be
displayed as follows even when the
ignition switch is in the ACC or LOCK
position.
The headlight switch must be in the
or position to see the display.
•
Displays for 10 minutes after the
ignition switch is turned to the ACC
or LOCK position from the ON
position.
•
Displays for 10 minutes after any
door is opened.
shuseizumi_J56J_8R29_EA_02I.book Page 24 Saturday, September 7, 2002 12:58 PM

5-30
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I

Charging System Warning Light
This warning light comes on when the
ignition switch is turned to the ON
position and goes off when the engine is
started.
If the warning light comes on while
driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off
the right-of-way. Consult an Authorized
Mazda Dealer.

Engine Oil Pressure Warning
Light
This warning light indicates low engine
oil pressure.
If the light comes on while driving:
1. Drive to the side of the road and park
off the right-of-way.
Brake Warning Light:Driving with the brake system
warning light on is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this
light remains on, after checking that
the parking brake is released, have
the brakes inspected immediately.
Don’t drive with this light on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
ABS Warning Light and Brake
Warning Light on at the Same Time:Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
Don’t continue driving when the
charging system warning light is
illuminated.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 30 Saturday, September 7, 2002 12:58 PM

5-31
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I
2. Turn off the engine and inspect the
engine oil level (page 8-10). If it’s low,
add oil.
3. Check the light.
If the light remains on even after you add
oil, have your vehicle towed to the nearest
service station or to an Authorized Mazda
Dealer.

Check Engine Light
If this light comes on while driving, the
vehicle may have a problem. It is
important to note the driving conditions
when the light came on and consult an
Authorized Mazda Dealer.
The check engine light may come on in
the following cases:
•
The fuel tank level being very low or
approaching empty.
•
The engine’s electrical system has a
problem.
•
The emission control system has a
problem.
•
The fuel-filler cap is missing or not
tightened securely.If the check engine light remains on, do
not drive at high speeds and consult an
Authorized Mazda Dealer as soon as
possible.

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible. Don’t run the engine if oil pressure is
low. It could result in extensive engine
damage.
CAUTION
ABS Warning Light and Brake Warning Light on at the Same Time:Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 31 Saturday, September 7, 2002 12:58 PM

5-36
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I

Cruise Main Indicator Light
This light comes on when the ON/OFF
switch is pressed and the cruise control
system is activated.

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.

Light-On Indicator Light (Black-
out meter)
This indicator light comes on when the
exterior lights are on.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.
Beeps
shuseizumi_J56J_8R29_EA_02I.book Page 36 Saturday, September 7, 2002 12:58 PM

5-37
Driving Your Mazda
Form No. 8R29-EA-02I
Switches and Controls

Headlights
To turn on the lights, turn the knob on the
end of the control lever.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Headlight High-Low Beam
Push the lever forward for high beam.
Pull it back for low.

Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.
Lighting Control
Lever Position OFF
Headlights Off Off On
Taillights
Parking lights
License lightsOff On On
NOTE
•
If the light switch is left on, the
lights will automatically switch off
30 seconds after turning the ignition
switch to the LOCK position or
removing the key.
The lights will automatically switch
back on when the ignition switch is
turned to the ACC or ON position.
•
To prevent discharging the battery,
don’t leave the lights on while the
engine is off.
Low beamHigh beam
shuseizumi_J56J_8R29_EA_02I.book Page 37 Saturday, September 7, 2002 12:58 PM

5-39
Driving Your Mazda
Switches and Controls
Form No. 8R29-EA-02I
Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn the front fog lights on, rotate the
fog light switch to the position.
The headlight switch must be in the
position to turn on the front fog lights.
To turn them off, rotate the fog light
switch to the or OFF position or turn
the headlight switch to the OFF position.The ignition switch must be in the ON
position.
Fog Lights
NOTE
The fog lights will turn off when the
headlights are set at high beam.
Fog light switch
Windshield Wipers and
Wa s h e r
Frozen Washer Fluid:Using windshield washer fluid in
freezing temperatures is dangerous.
The washer fluid could freeze on the
windshield and block your vision.
You could have an accident. Don’t use
the washer without first warming the
windshield.
NOTE
Because heavy ice and snow can jam
the wiper blades, the wiper motor is
protected from motor breakdown,
overheating and possible fire by a
circuit breaker. This mechanism will
automatically stop operation of the
blades, but only for about 5 minutes.
If this happens, turn off the wiper
switch and park off the right-of-way,
and remove the snow and ice.
After 5 minutes, turn on the switch and
the blades should operate normally. If
they don’t resume functioning, consult
an Authorized Mazda Dealer as soon
as possible.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 39 Saturday, September 7, 2002 12:58 PM

6-6
Interior Comfort
Climate Control System
Form No. 8R29-EA-02I

Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.Fan control dial
This dial allows variable fan speeds.
0—Fan off
1—Low speed
2—Medium low speed
3—Medium high speed
4—High speed
Manual Type
Temperature control dial Fan control dial Mode selector dial
Air intake selector
A/C SwitchRear window
defroster switch
(page 5-41)
Cold Hot
shuseizumi_J56J_8R29_EA_02I.book Page 6 Saturday, September 7, 2002 12:58 PM