oil MAZDA MODEL 626 2002 Owner's Manual

8-17
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Inspecting Power Steering Fluid
Level
Inspect the fluid level at each engine oil
change. Add fluid if necessary; it does not
require periodic changing.
The level must be kept between the HIGH
and LOW marks.
Visually examine the lines and hoses for
leaks and damage.
1. Park on a level surface, well off the
right-of-way, and set the parking brake
firmly.
2. Turn off the engine and allow it to cool. 3. Remove the filler cap and attached
dipstick.
4. Wipe them clean and put them back.
5. Remove again and inspect the level.
6. It must be between HIGH and LOW. Add fluid if necessary.
Don ’t overfill.
If new fluid is required frequently, consult
an Authorized Mazda Dealer.
Power Steering Fluid
To avoid damage to the power steering
pump, don’ t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-4).
CAUTION
High
Low OK
J94S.book Page 17 Saturday, June 23, 2001 1:04 PM

8-21
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
All moving points of the body, such as
door and hood hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the engine hood’s secondary
latch keeps the hood from opening when
the primary latch is released. A viscous paper air filter fits inside the air
cleaner housing, as shown. It
’s been
specially treated and should not be
cleaned and reused. Replace it when
necessary.





Replacing the Air Filter
1. Unfasten the clamps.
Body LubricationAir Filter
Don ’t drive without an air filter. This
could result in excessive engine wear.
NOTE
If the vehicle is operated in very dusty
or sandy areas, replace the filter more
often than recommended intervals.
CAUTION
Clamp
J94S.book Page 21 Saturday, June 23, 2001 1:04 PM

8-30
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Yo u r M a z d a’s headlights have replaceable
halogen bulbs.




Replacing a Headlight Bulb
1. Make sure the headlight switch is off.
2. Lift the hood and find the bulb in the
rear of the headlight body.
3. 2.5-liter engine Remove the bolts and the coolant
reservoir.
4. Detach the electrical connector from the bulb by squeezing the tabs and
pulling it to the rear.
Handling Halogen Bulbs:When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when lit.
Never touch the glass portion of the
bulb with your bare hands and always
wear eye protection when handling or
working around halogen bulbs.
Children and Halogen Bulbs:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
Always keep halogen bulbs out of the
reach of children.
WARNING
Do not touch the glass surface
Bolts
J94S.book Page 30 Saturday, June 23, 2001 1:04 PM

8-43
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for metallic, mica, and solid colors. 3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.





Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.





Bright-Metal Maintenance
• Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
• To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
• During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn ’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J94S.book Page 43 Saturday, June 23, 2001 1:04 PM

8-45
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G





Dashboard Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
dashboard. They ’ll damage and discolor
it. If these solutions get on the dashboard,
wipe them off immediately.





Cleaning the Upholstery and
Interior Trim
Vinyl
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl with a leather-and-vinyl
cleaner.
Leather
Real leather isn ’t uniform and may have
scars, scratches, and wrinkles. Clean it
with a leather cleaner or mild soap.
Wipe it with a damp soft cloth; then dry
and buff it with a dry soft cloth.
Fabric
Remove dust and loose dirt from fabric
with a whisk broom or vacuum cleaner.
Clean it with a mild soap solution good
for upholstery and carpets. Remove fresh
spots immediately with a fabric spot
cleaner.
To keep the fabric looking clean and
fresh, take care of it. Otherwise its color
will be affected, it can be stained easily,
and its fire-resistance may be reduced.





Cleaning the Lap/Shoulder Belt
We b b i n g
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Don ’t bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is
no remaining moisture before retracting
them.





Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them
with glass cleaner. Follow the directions
on the container.
Interior Care
Use only recommended cleaners and
procedures. Others may affect
appearance and fire-resistance.
Damaged Seat Belt:Using damaged seat belts is
dangerous. In a collision, damaged
belts cannot provide adequate
protection. Have your Authorized
Mazda Dealer replace damaged belts
immediately.
Don ’t scrape or scratch the inside of
the rear window. You may damage the
rear window defroster grid.
CAUTION
WARNING
CAUTION
J94S.book Page 45 Saturday, June 23, 2001 1:04 PM

10-4
Form No. 8Q50-EA-01G
Specifications





Engine






Electrical System
*1Manual transaxle*2Automatic transaxle






Lubricant Quality
*Refer to the recommended SAE viscosity numbers on 8-10.
Specifications
Model
Item 2.0-liter engine 2.5-liter engine
Type DOHC-16V in-line, 4-cyl DOHC-24V V6 6-cyl
Bore ×Stroke 83.0 × 92.0mm (3.27 × 3.62 in) 84.5 × 74.2mm (3.33 × 2.92 in)
Displacement 1,991 ml (1,991 cc , 121.5 cu in) 2,496 ml (2,496 cc , 152.3 cu in)
Compression ratio 9.19.5
Model
Item 2.0 liter engine
2.5-liter engine
Battery Maintenance-free 12V-48AH/5HR
Alternator 12V-80A12V-90A
Starter 12V-1.0 kW
12V-1.7 kW
*1, 12V-1.6 kW *2
Spark-plug
numberNGK BKR5E-11, BKR6E-11
—
DENSO K16PR-U11, K20PR-U11 PKJ16CR8, PKJ20CR8
Spark-plug gap 1.0 —1.1 mm (0.040 —0.043 in) 0.7 —0.8 mm (0.028 —0.031 in)
Lubricant Classification
Engine oil
*
API Service ILSAC
SG (Energy Conserving II) —
SH (Energy Conserving II) GF-I
SJ GF-II
SL GF-III
Manual transaxle oil Any temperature
API Service GL-4 or GL-5
(SAE 75W-90)
Above 50
°F (10 °C)
API Service GL-4 or GL-5
(SAE 80W-90)
Automatic transaxle fluid 2.0-liter engine ATF M-III or equivalent (e.g. Mercon
®)
2.5-liter engine ATF M-III or equivalent (e.g. Dexron ® III)
Power steering fluid ATF M-III or equivalent (e.g. Dexron® II)
Brake/clutch fluid SAE J1703 or FMVSS116 DOT-3
J94S.book Page 4 Saturday, June 23, 2001 1:04 PM

10-5
Specifications
Form No. 8Q50-EA-01G





Capacities
(Approximate Quantities)
*The indicated engine oil capacities are for general reference purposes only. When adding
or changing oil, verify the engine oil level with the oil dipstick.






Dimensions
Unit: mm (in)






We i g h t s
Unit: kg (lb)
GVWR: Gross Vehicle Weight Rating
GAWR: Gross Axle Weight Rating
Unit
Item L US qt Imp qt
Engine oil
*
2.0-liter engine with oil filter
replacement
3.5 3.7 3.1
without oil filter
replacement 3.3 3.5 2.9
2.5-liter engine with oil filter
replacement
4.0 4.2 3.5
without oil filter
replacement 3.7 3.9 3.3
Coolant 7.5 7.9 6.6
Transaxle oil Manual transaxle 2.7 2.9 2.4
Automatic
transaxle
2.0-liter engine 8.86 9.37 7.80
2.5-liter engine 8.0 8.5 7.0
Fuel tank L US gal Imp gal
64.0 16.9 14.1
Overall length 4,760 (187.4)
Overall width 1,760 (69.3)
Overall height 1,400 (55.1)
Front tread 1,500 (59.1)
Rear tread 1,490 (58.7)
Wheelbase 2,670 (105.1) Model
Item 2.0-liter engine 2.5-liter engine
GVWR 1,771 (3,904) 1,827 (4,028)
GAWR Front 959 (2,114) 1,004 (2,214)
Rear 812 (1,790) 823 (1,814)
J94S.book Page 5 Saturday, June 23, 2001 1:04 PM

11-3
Index
Form No. 8Q50-EA-01G
D
Driving Tips ....................................... 4-7
Automatic transaxle
.................. 5-12
Break-in period
........................... 4-7
Driving in flooded area
............. 4-10
Hazardous driving
....................... 4-8
Money-saving suggestions
.......... 4-7
Rocking the vehicle
.................... 4-8
Trailer towing
........................... 4-11
Winter driving
............................. 4-9
E
Emergency Starting .......................... 7-12
Flooded engine
.......................... 7-12
Jump-starting
............................ 7-12
Push-starting
............................. 7-14
Emergency Towing
.......................... 7-15
Emission Control System
................... 4-4
Engine Coolant
...................................... 8-13
Exhaust gas
................................. 4-5
Hood release
............................... 3-9
Oil
............................................. 8-10
Overheating
............................... 7-10
Starting
........................................ 5-3
Engine Compartment Overview
........ 8-9
Engine Coolant Overheating
............................... 7-10
Engine Coolant Temperature
Gauge
............................................... 5-21
Exhaust Gas
....................................... 4-5
Exterior Care
.................................... 8-42
Eyeglass Holder
............................... 6-41
F
Flasher Hazard warning
.........................5-36
Headlights
.................................5-32
Flat Tire
..............................................7-3
Changing
.....................................7-5
Spare tire and tool storage
...........7-3
Fluids Classification
.............................10-4
Owner maintenance
.....................8-7
Foot Brake
..........................................5-4
Front seats
..........................................2-2
Fuel Filler lid and cap
.......................3-14
Gauge
........................................5-22
Requirements
..............................4-2
Tank capacity
............................10-5
Fuses
.................................................8-35
Panel description
.......................8-37
Replacement
..............................8-35
G
Gauges ..............................................5-19
Glove Box
........................................6-42
H
Hazard Warning Flasher ...................5-36
Hazardous Driving
.............................4-8
Headlights Control
......................................5-32
Flashing
.....................................5-32
High-low beam
..........................5-32
On reminder
..............................5-32
Hood Release
......................................3-9
Horn
..................................................5-36
J94S.book Page 3 Saturday, June 23, 2001 1:04 PM

11-6
Index
Form No. 8Q50-EA-01G
T
Trunk Release Handle ...................... 3-12
Turn and Lane-Change Signals
....... 5-33
V
Vanity Mirrors ................................. 6-44
Vehicle Information Labels
............. 10-2
W
Warning Lights ................................ 5-23
ABS
.......................................... 5-28
Air bag system
.......................... 5-28
Brake system
............................ 5-25
Charging system
....................... 5-26
Check engine
............................ 5-27
Door-ajar
................................... 5-28
Engine oil pressure
................... 5-26
Immobilizer system
.................. 5-29
Low fuel
.................................... 5-27
Low washer fluid level
............. 5-27
Seat belt
.................................... 5-25
TCS
........................................... 5-27
Warranty
............................................ 9-8
Washer Fluid
.................................... 8-20
Weights
............................................ 10-5
Wheel Replacement
......................... 8-28
Windows Power windows
.......................... 3-7
Windshield Washer
.......................... 5-35
Windshield Wipers
.......................... 5-34
Blades replacement
................... 8-22
Winter Driving
................................... 4-9
J94S.book Page 6 Saturday, June 23, 2001 1:04 PM