engine coolant MAZDA MODEL B-SERIES 2004 (in English) Owner's Manual

How Limp to Safety works
If the engine begins to overheat:
•The engine coolant temperature
gauge will move to the red (hot)
area.
• The
symbol will illuminate.
• The “Service Engine Soon”
indicator light will illuminate.
If the engine reaches a preset over-temperature condition, the engine
will automatically switch to alternating cylinder operation. Each disabled
cylinder acts as an air pump and cools the engine.
When this occurs the vehicle will still operate. However:
• The engine power will be limited.
• The air conditioning system will be disabled.
This system has given you an early warning of engine damage and you
should immediately drive to a place of safety where the engine can be
cooled or the vehicle towed to a service shop. Continuing to drive in this
Limp to Safety mode will increase engine temperature some more,
increasing the chance of engine damage, and:
• The engine will completely shut down.
• Steering and braking effort will increase.
If you have decided not to have the vehicle towed, and when the engine
temperature cools, you try to re-start it and it appears to have returned
to normal operation, don’ t delay in getting to a service facility as soon as
possible to diagnose what caused the overheat and prevent further
engine damage.
When Limp to Safety mode is activated
You have limited engine power when in the Limp to Safety mode, so
drive the vehicle with caution. The vehicle will not be able to maintain
high speed operation and the engine will run rough. Remember that the
engine is capable of completely shutting down automatically to prevent
engine damage, therefore:
1. Pull off the road as soon as safely possible and turn off the engine.
2. Arrange for the vehicle to be taken to a service facility.
3. If this is not possible, wait for the engine to cool down.
4. When the engine has cooled down, first check the coolant level. If low, then use a rag and carefully turn the cap one notch
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
207

counter-clockwise carefully to avoid being burned by hot steam.
When there is no steam, keep you face back as you carefully remove
the cap and then replenish the coolant to the full line.
WARNING: Never remove the coolant reservoir cap while the
engine is running or hot.
5. Replace the cap and see if the engine starts and runs normally and drive it to a service place under reduced load and with the air
conditioning off. If it quickly goes into Limp to Safety mode again,
shut it down in a safe location and have the vehicle towed for
service.
WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS
Important safety precautions WARNING: Do not overfill the fuel tank. The pressure in an
overfilled tank may cause leakage and lead to fuel spray and
fire.
WARNING: The fuel system may be under pressure. If the fuel
filler cap is venting vapor or if you hear a hissing sound, wait
until it stops before completely removing the fuel filler cap.
Otherwise, fuel may spray out and injure you or others.
WARNING: If you do not use the proper fuel filler cap,
excessive pressure or vacuum in the fuel tank may damage the
fuel system or cause the fuel cap to disengage in a collision,
which may result in possible personal injury.
WARNING: Automotive fuels can cause serious injury or death
if misused or mishandled.
WARNING: Fuel ethanol and gasoline may contain benzene,
which is a cancer-causing agent.
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
208

•4.0L V6 engine
Check the power steering fluid. Refer to the service maintenance section
for the service interval schedules. If adding fluid is necessary, use only
MERCON AT F.
1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be
near the center of the normal area between H and C).
2. While the engine idles, turn the steering wheel left and right several times.
3. Turn the engine off.
4. If your vehicle is equipped with a 3.0L V6 engine, check the
fluid level on the dipstick. It should be within the FULL HOT range.
Do not add fluid if the level is within this range.
5. If your vehicle is equipped with a 4.0L SOHC V6 or 2.3L I4
engine, check the fluid level in the reservoir. It should be between
the MIN and MAX lines. Do not add fluid if the level is within this
range.
6. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the FULL HOT range. Be sure to put the
dipstick back in the reservoir.
DONOTOVERFILLPOWERSTEERINGFLUID
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
220

FluidMazda Part
NameApplication Capacity
Engine coolant
4Premium Engine
Coolant 2.3 L I4 engine
with manual
transmission10.0L (10.5
quarts)
2.3L I4 engine
with automatic
transmission 9.7L (10.2
quarts)
3.0L V6 engine
with manual
transmission 14.3L (15.1
quarts)
3.0L V6 engine
with automatic
transmission 14.0L (14.8
quarts)
4.0L V6 engine
with manual
transmission 13.0L (13.7
quarts)
4.0L V6 engine
with automatic
transmission 12.5L (13.2
quarts)
Fuel tank N/A Regular cab
(Short wheel
base)64.4L (17
gallons)
SuperCab 73.8L (19.5 gallons)
Transfer Case
Fluid Mazda
MERCON
AT F4x4 Vehicles 1.2L (1.25
quarts)
Front axle
lubricant Mazda SAE
80W-90
Premium Rear
Axle Lubricant4x4 Vehicles 1.7L (3.6 pints)
Rear axle
lubricant
5Mazda SAE
80W-90
Premium Rear
Axle Lubricant All
2.4-2.5L (5.0-5.3
pints)
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
241

FluidMazda Part
NameApplication Capacity
Windshield
washer fluid Ultra-Clear
Windshield
Washer
ConcentrateAll
2.6L (2.75
quarts)
1Ensure the correct automatic transmission fluid is used. Transmission
fluid requirements are indicated on the dipstick or on the dipstick
handle. MERCON and MERCONV are not interchangeable. DO NOT
mix MERCON and MERCONV. Refer to the service maintenance
section to determine the correct service interval.
2Service refill capacity is determined by filling the transmission to the
bottom of the filler hole with the vehicle on a level surface.
3Indicates only approximate dry-fill capacity. Some applications may vary
based on cooler size and if equipped with an in-tank cooler. The amount
of transmission fluid and fluid level should be set by the indication on
the dipstick’ s normal operating range.
4Add the coolant type originally equipped in your vehicle. DO NOT MIX
different colors or types of coolant. DO NOT USE Mazda Extended Life
Engine Coolant (orange in color). Refer to Adding engine coolant, in
this chapter.
5Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant.
Add 118 ml (4 oz.) of Additive Friction Modifier meeting Mazda
specifications for complete refill of Traction-Lok axles. Service refill
capacities are determined by filling the rear axle 6 mm to 14 mm (1/4
inch to 9/16 inch) below the bottom of the filler hole.
6Brake fluid will drop slowly as the brakes wear and will rise when brake
components are replaced. Fluid levels below the MAX line that do not
trigger the brake warning light are within the normal operating range,
there is no need to add fluid. If the levels are outside the normal
operating range, the performance of your brake system could be
compromised, seek service from your local Mazda dealer immediately.
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
242

LUBRICANT SPECIFICATIONS
ItemMazda part name or equivalent
Front axle (4X4) SAE 80W-90 Premium Rear Axle
Lubricant
Rear axle SAE 80W-90 Premium Rear Axle
Lubricant
1
Brake fluid and clutch fluid (if
equipped)High Performance DOT 3 Motor
Vehicle Brake Fluid
4
Door weather strips
Silicone Lubricant
Engine coolant Mazda Premium Engine Coolant3
Engine oil 2.3L I4 and 3.0L V6
enginesSAE 5W-20 Motor Oil
Engine oil 4.0L V6 engines SAE 5W-30 Motor Oil
Hinges, door checks, latches,
striker plates, fuel filler door hinge
and seat tracks Multi-Purpose Grease
Transmission /steering/parking
brake linkages and pivots, brake
and clutch pedal shaft, clutch pilot
bearing and input shaft spline
(manual transmission). Premium Long-Life Grease
Power steering fluid, transfer case
fluid (4X4) and transmission fluid
(manual) MERCON
AT F
Automatic transmission (5R44E
and 5R55E) MERCONVATF
2
Windshield washer fluid
Ultra-clear Windshield Washer
Concentrate
1Add 118 ml (4 oz.) of Additive Friction Modifier meeting Mazda
specifications for complete refill of Traction-Lok axles. If submerged in
water, the rear axle lubricant should be changed.
2Ensure the correct automatic transmission fluid is used. Transmission
fluid requirements are indicated on the dipstick or on the dipstick
handle. MERCON and MERCONV are not interchangeable. DO NOT
mix MERCON and MERCONV. Refer to your service maintenance
section to determine the correct service interval.
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
243

3Do not mix different types or colors of engine coolant.
4Brake fluid will drop slowly as the brakes wear and will rise when brake
components are replaced. Fluid levels below the MAX line that do not
trigger the brake warning light are within the normal operating range,
there is no need to add fluid. If the levels are outside the normal
operating range, the performance of your brake system could be
compromised, seek service from your local Mazda dealer immediately.
ENGINE SPECIFICATIONS
Engine 2.3L I4 engine 3.0L V6 engine 4.0L V6 engine
Cubic inches 138 182 245
Required fuel 87 octane 87 octane 87 octane
Firing order 1-3-4-2 1-4-2-5-3-6 1-4-2-5-3-6
Spark plug gap 1.04-1.19mm
(0.041-0.047
inch)1.07-1.17mm
(0.042-0.046
inch)1.3-1.4 mm
(0.052-0.056
inch)
Ignition system EDIS EDISEDIS
Compression
ratio 9.7:1
9.14:19.7:1
VEHICLE DIMENSIONS
Vehicle dimensions Regular Cab mm (in)SuperCab mm
(in)
(1) Overall length 4 786 (188.4) 5 168 (203.4)
(2) Overall width 1 785 (70.3) 1 785 (70.3)
(3) Overall height 4x2/4x4 1 651 (65.0) / 1 727 (68.0)1 651 (65.0) /
1 727 (68.0)
(4) Wheelbase 2 831 (111.4) 3 192 (125.7)
(5) Track - Front 1 486 (58.5) 1 485 (58.5)
(5) Track - Rear 1 455 (57.3) 1 455 (57.3)
2004 Mazda B Series(mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Maintenance and Specifications
244

A
ABS (see Brakes) .....................110
Air bag supplemental restraint
system ..........................................78and child safety seats ..............80
description ................................78
disposal ......................................84
driver air bag ............................82
indicator light ...........................83
operation ...................................82
passenger air bag .....................82
passenger deactivation
switch ........................................84
Ambulance packages ....................7
Antifreeze
(see Engine coolant) ................202
Anti-lock brake system
(see Brakes) ......................110–111
Audio system 6-CD in dash .............................22
Single CD ..................................19
Audio system
(see Radio) ................18–19, 22, 26
Automatic dimming rear view
mirror ...........................................46
Automatic transmission ............114 driving an automatic
overdrive .................................115
fluid, refill capacities ..............240
fluid, specification ..................244
Auxiliary power point .................45
Axle lubricant
specifications ..................243–244
refill capacities ........................240
traction lok ..............................113
B
Battery .......................................200 acid, treating emergencies .....200
jumping a disabled battery ....156
maintenance-free ....................200
servicing ..................................200
Bed extender ..............................53
BeltMinder ...................................73
Brakes ........................................110 anti-lock ...........................110–111
anti-lock brake system (ABS)
warning light ...........................111
fluid, checking and adding ....221
fluid, refill capacities ..............240
fluid, specifications .........243–244
lubricant
specifications ..................243–244
parking ....................................112
shift interlock ..........................114
Break-in period .............................5
Bulbs ............................................36
C
Calculating load ........................127
Capacities for refilling fluids ....240
Cassette tape player .......19, 22, 26
Cell phone warning ...................247
Certification Label ....................246
Changing a tire ...................49, 149
Child safety restraints ................90 child safety belts ......................90
Child safety seats ........................93 attaching with tether straps ....98
in front seat ..............................95
in rear seat ................................95
LATCH .....................................102
tether anchorage hardware .....98
Chimes (warning) .......................16
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Index
Index
248

Cleaning your vehicleengine compartment ..............174
exterior ............................174, 178
exterior lamps .........................176
instrument cluster lens ..........177
instrument panel ....................177
interior .....................................177
Mazda car care products .......178
mirrors .....................................176
plastic parts ............................176
washing ....................................173
waxing .....................................173
wheels ......................................174
windows ..................................178
wiper blades ............................176
Clock adjust AM/FM Stereo ...........................18
AM/FM stereo CD .....................20
AM/FM stereo tape/CD/MP3 ....23
Premium AM/FM stereo
CD6/MP3 ...................................26
Single CD ..................................19
Clutch fluid ..........................................221
operation while driving ..........117
recommended shift speeds ....118
Compass, electronic ..............46 –47
calibration .................................48
set zone adjustment .................47
Console ........................................53
Coolant checking and adding ..............202
refill capacities ................205, 240
specifications ..................243–244
Cruise control
(see Speed control) ....................49
Customer
Assistance ..................162–163, 166 D
Daytime running lamps
(see Lamps) ................................34
Dipstick
engine oil .................................192
Doors lubricant specifications ..........243
Driveline universal joint and
slip yoke ....................................225
Driving under special
conditions ..................119, 121–122 mud ..........................................122
sand .........................................122
snow and ice ...........................123
through water .................122–123
E
Emergencies, roadside jump-starting ..........................156
Emergency Flashers .................137
Emission control system ..........217
Engine ........................................244 cleaning ...................................174
coolant .....................................202
idle speed control ...................200
limp to safety cooling .............206
lubrication
specifications ..................243–244
refill capacities ........................240
service points ..................189–191
starting after a collision .........137
Engine block heater .................109
Engine oil ..................................192 checking and adding ..............192
dipstick ....................................192
filter, specifications ................198
recommendations ...................198
2004 Mazda B Series (mbs)
Owners Guide (post-2002-fmt)
Canadian French (fr-can)
Index
249