ignition MAZDA MODEL CX-3 2015 (in English) Service Manual

*Some models.4–24
When Driving
Instrument Cluster and Display


Trip Computer and INFO Switch .......................................................................... page 4-31



Speed Unit Selector ............................................................................................... page 4-24



Odometer, Trip Meter, Trip Computer and Trip Meter Selector ........................... page 4-26
Speedometer
The speedometer indicates the speed of the
vehicle.
NOTE
(Analog speedometer type)
If a few seconds have elapsed after
switching the ignition off, the needle
may deviate. However, this does not
indicate a problem.
Speed Unit Selector (Digital
Speedometer Type) *
In some countries, you may have to
change the speed units between km/h and
mph.
Press the speed unit selector for 1.5
seconds or more.
The speed units for the speedometer will
change between km/h and mph.
Speedometer
Speed unit selector
Odometer, Trip Meter and Trip
Meter Selector *
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.
Press the selector Press the selector
Press the selector Odometer
Trip meter A
Trip meter BSelector
$9@&;&&%@&EJUJPOJOEC







4–25
When Driving
Instrument Cluster and Display
NOTE
When the ignition is switched to ACC
or off, the odometer or trip meters
cannot be displayed, however, pressing
the selector can inadvertently switch
the trip meters or reset them during an
approximate ten-minute period in the
following cases:
 
 After the ignition is switched to off
from ON.
  After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is fi lled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed. The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
NOTE
 (Vehicles with type C/type D audio) If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
 Refer to Fuel Economy Monitor on
page 4-88 .
  Only the trip meters record tenths of
kilometres (miles).
  The trip record will be erased when:




 The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


 The vehicle is driven over 9999.9
km (mile).
$9@&;&&%@&EJUJPOJOEC







*Some models.4–26
When Driving
Instrument Cluster and Display
Odometer, Trip Meter, Trip
Computer and Trip Meter
Selector
*
The display mode can be changed
between trip meter A and trip meter B by
pressing the selector while one of them
is displayed. The selected mode will be
displayed.
Selector
Current fuel economy modeDistance-to-empty modeTrip meter B Trip meter AOdometer
NOTE
When the ignition is switched to ACC
or off, the odometer or trip meters
cannot be displayed, however, pressing
the selector can inadvertently switch
the trip meters or reset them during an
approximate ten-minute period in the
following cases:
 
 After the ignition is switched to off
from ON.
  After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is fi lled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
The trip meter records the total distance
the vehicle is driven until the meter is
again reset. Return it to “0.0” by holding
the selector depressed for 1 second
or more. Use this meter to measure
trip distances and to compute fuel
consumption.
$9@&;&&%@&EJUJPOJOEC







4–27
When Driving
Instrument Cluster and Display
NOTE
 (Vehicles with type C/type D audio) If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
 Refer to Fuel Economy Monitor on
page 4-88 .
  Only the trip meters record tenths of
kilometres (miles).
  The trip record will be erased when:




 The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


 The vehicle is driven over 9999.9
km (mile).
Trip Computer
The following information can be selected
by pressing the selector with the ignition
switched ON.
 


 Approximate distance you can travel on
the available fuel
 


 Current fuel economy
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer. Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
NOTE
  Even though the distance-to-empty
display may indicate a suffi cient
amount of remaining driving distance
before refuelling is required, refuel
as soon as possible if the fuel level
is very low or the low fuel warning
light illuminates.
  The display may not change unless
you add more than approximately 9 L
(2.3 US gal, 1.9 Imp gal) of fuel.
  The distance-to-empty is the
approximate remaining distance the
vehicle can be driven until all the
graduation marks in the fuel gauge
indicating the remaining fuel supply
disappear.
  If there is no past fuel economy
information such as after fi rst
purchasing your vehicle or the
information is deleted when the
battery leads are disconnected, the
actual distance-to empty/range may
differ from the amount indicated.
$9@&;&&%@&EJUJPOJOEC







4–29
When Driving
Instrument Cluster and Display
NOTE
When the tachometer needle enters the
STRIPED ZONE, this indicates to the
driver that the gears should be shifted
before entering the RED ZONE.
Fuel Gauge
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full.
Full
1/4 Full
Empty
If the low fuel warning light illuminates or
the fuel level is very low, refuel as soon as
possible.
Refer to Warning/Indicator Lights on page
4-36 .
NOTE
  After refuelling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve
since the fuel moves in the tank.
  The display indicating a quarter
or less remaining fuel has more
segments to show the remaining fuel
level in greater detail.
  The direction of the arrow ()
indicates that the fuel-fi ller fl ap is on
the left side of the vehicle.
(SKYACTIV-D 1.5)
If inconsistency in engine performance
or stalling occurs due to low fuel level
conditions, refuel the vehicle as soon as
possible and add at least 10 L (2.7 US gal,
2.2 Imp gal) of fuel.
Instrument panel Illumination
When the position lights are turned
on with the ignition switched ON,
the brightness of the instrument panel
illumination is dimmed.
NOTE
When the position lights are turned on,
the position lights indicator light in the
instrument cluster turns on.
Refer to Headlights on page 4-58 .
$9@&;&&%@&EJUJPOJOEC







*Some models.4–30
When Driving
Instrument Cluster and Display
The brightness of the instrument panel
and instrument panel illuminations can be
adjusted by rotating the knob.
 


 The brightness decreases by rotating the
knob to the left. A beep sound will be
heard when the knob has been rotated to
the maximum dim position.
 


 The brightness increases by rotating the
knob to the right.
Dim
Bright
Function for cancelling illumination
dimmer
The illumination dimmer can be
cancelled by rotating the instrument panel
illumination knob to the right until a beep
sound is heard while the instrument cluster
is dimmed with the ignition switched
ON. If the instrument cluster's visibility
is reduced due to glare from surrounding
brightness, cancel the illumination
dimmer.
NOTE
  When the illumination dimmer is
cancelled, the instrument cluster
cannot be dimmed even if the
position lights are turned on.
  When the illumination dimmer is
cancelled, the screen in the centre
display switches to constant display
of the daytime screen.
Outside Temperature Display *
When the ignition is switched ON, the
outside temperature is displayed.
NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and
vehicle conditions:
 


 Signifi cantly cold or hot
temperatures.
 


 Sudden changes in outside
temperature.
 


 The vehicle is parked.



 The vehicle is driven at low
speeds.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–31
When Driving
Instrument Cluster and Display
Cruise Control Set Vehicle Speed
Display*
The vehicle speed preset using the cruise
control is displayed.
Trip Computer and INFO Switch *
The following information can be selected
by pressing the up
or down part of the
INFO switch with the ignition switched
ON.
 


 Approximate distance you can travel on
the available fuel
 


 Average fuel economy



 Current fuel economy



 Average vehicle speed



 Vehicle speed alarm *
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
(European model)
(Except European model)
NOTE
  Even though the distance-to-empty
display may indicate a suffi cient
amount of remaining driving distance
before refuelling is required, refuel
as soon as possible if the fuel level
is very low or the low fuel warning
light illuminates.
  The display may not change unless
you add more than approximately 9 L
(2.3 US gal, 1.9 Imp gal) of fuel.
  The distance-to-empty is the
approximate remaining distance
the vehicle can be driven until all
the graduation marks in the fuel
gauge (indicating the remaining fuel
supply) disappear.
  If there is no past fuel economy
information such as after fi rst
purchasing your vehicle or the
information is deleted when the
battery leads are disconnected, the
actual distance-to empty/range may
differ from the amount indicated.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–39
When Driving
Instrument Cluster and Display
Signal Warning Lights Page
(Amber)
* Mazda Radar Cruise Control (MRCC) Warning Light *1 7-35
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or
when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an
expert repairer, we recommend an Authorised Mazda Repairer.
*2 The light turns on continuously when the parking brake is applied.
Indicator Lights
These lights turn on or fl ash to notify the user of the system operation status or a system
malfunction.
Signal Indicator Lights Page
* Blind Spot Monitoring (BSM) OFF Indicator Light *1 4-116
* Lane Departure Warning System (LDWS) OFF Indicator
Light*1 4-108
(Green) KEY Indicator Light 3-8
(Green) * Seat Belt Indicator Light (Rear seat) 2-17
(Green)
* High Beam Control System (HBC) Indicator Light 4-104
* Glow Indicator Light *1 4-43
* Diesel Particulate Filter Indicator Light *1 4-167
* Wrench Indicator Light *1 4-42
* TCS/DSC Indicator Light *1 4-82 , 4-84
* TCS OFF Indicator Light *1 4-83
$9@&;&&%@&EJUJPOJOEC







*Some models.4–41
When Driving
Instrument Cluster and Display
Signal Indicator Lights Page
(Green)
* Adjustable Speed Limiter Set Indicator Light 4-136
* Select Mode Indicator Light 4-94
Lights-On Indicator Light 4-58
* Front Fog Light Indicator Light 4-65
* Rear Fog Light Indicator Light 4-66
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or
when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an
expert repairer, we recommend an Authorised Mazda Repairer.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–42
When Driving
Instrument Cluster and Display
Wrench Indicator Light
When the ignition is switched ON, the
wrench indicator light is illuminated and
then turns off after a few seconds.
The wrench indicator light is illuminated
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
SKYACTIV-D 1.5
The wrench indicator light turns on
when the engine oil has deteriorated, is
insuffi cient
* , is around the X mark on
the oil level gauge or reaches a position
exceeding the X mark.
Check the engine oil. Refer to Inspecting
Engine Oil Level on page 6-28 .
Replace the engine oil if the wrench
indicator light does not turn off even
though the engine oil level is in the normal
range.
NOTE
  Depending on the vehicle use
conditions, the wrench indicator light
may turn on for reasons other than
the preset maintenance period.
  Whenever the engine oil is replaced,
a reset of the vehicle engine control
unit necessary.
 Your Authorised Mazda Repairer will
be able to reset the engine control
unit or see page 6-27 for the Vehicle
engine control unit reset procedure.
Low Engine Coolant Temperature
Indicator Light (Blue)
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suffi ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
$9@&;&&%@&EJUJPOJOEC