battery MAZDA MODEL CX-3 2015 Owners Manual (in English)

2–7
Essential Safety Equipment
Seats
NOTE
  If the ignition is switched off while
the seat warmer is operating (High,
Mid or Low) and then switched
ON again, the seat warmer will
automatically operate at the
temperature set before switching off
the ignition.
  Use the seat warmer when the engine
is running. Leaving the seat warmer
on for long periods with the engine
not running could cause the battery
power to be depleted.
  The temperature of the seat warmer
cannot be adjusted beyond High, Mid
and Low because the seat warmer is
controlled by a thermostat.
Rear Seat
Split Folding the Seatbacks
By lowering the rear seatbacks the luggage
compartment space can be expanded.
WARNING
Do not drive the vehicle with occupants
on folded down seatbacks or in the
luggage compartment.
Putting occupants in the luggage
compartment is dangerous because seat
belts cannot be fastened which could
lead to serious injury or death during
sudden braking or a collision.
Do not allow children to play inside the
vehicle with the seatbacks lowered.
Allowing children to play in the vehicle
with the seatbacks folded down is
dangerous. If a child enters the luggage
compartment and the seatbacks were
raised back up, the child may become
trapped in the luggage compartment
which could lead to an accident.
Tightly secure cargo in the luggage
compartment when it is transported
with the seatbacks folded down.
Driving without tightly securing cargo
and luggage is dangerous as it could
move and become an obstruction to
driving during emergency braking or
a collision resulting in an unexpected
accident.
$9@&;&&%@&EJUJPOJOEC







2–14
Essential Safety Equipment
Seat Belt Systems
WARNING
Instructions for Use of Seat Belt Assemblies:
Seatbelts are designed to bear upon the bony structure of the body, and should be worn
low across the front of the pelvis or the pelvis, chest and shoulders, as applicable;
wearing the lap section of the belt across the abdominal area must be avoided.
Seatbelts should be adjusted as fi rmly as possible, consistent with comfort, to provide
the protection for which they have been designed. A slack belt will greatly reduce the
protection afforded to the wearer.
Care should be taken to avoid contamination of the webbing with polishes, oils and
chemicals, and particularly battery acid. Cleaning may safely be carried out using mild
soap and water. The belt should be replaced if webbing becomes frayed, contaminated
or damaged.
It is essential to replace the entire assembly after it has been worn in a severe impact
even if damage to the assembly is not obvious.
Belts should not be worn with straps twisted.
Each belt assembly must only be used by one occupant; it is dangerous to put a belt
around a child being carried on the occupant's lap.
No modifi cations or additions should be made by the user which will either prevent
the seat belt adjusting devices from operating to remove slack, or prevent the seat belt
assembly from being adjusted to remove slack.
CAUTION
Belt retraction may become diffi cult if the belts and rings are soiled, so try to keep them
clean. For more details about cleaning the seat belts, refer to "Cleaning the Lap/Shoulder
Belt Webbing" (page 6-68 ).
Ring
$9@&;&&%@&EJUJPOJOEC







3–2
Before Driving
Keys
Keys
WARNING
Do not leave the key in your vehicle
with children and keep them in a place
where your children will not fi nd or
play with them:
Leaving children in a vehicle with the
key is dangerous. This could result in
someone being badly injured or even
killed. Children may fi nd these keys
to be an interesting toy to play with
and could cause the power windows or
other controls to operate, or even make
the vehicle move.
CAUTION
  Because the key (transmitter) uses
low-intensity radio waves, it may
not function correctly under the
following conditions:
 


 The key is carried with
communication devices such as
cellular phones.
 


 The key contacts or is covered by a
metal object.
 


 The key is near electronic devices
such as personal computers.
 


 Non-Mazda genuine electronic
equipment is installed in the
vehicle.
 


 There is equipment which
discharges radio waves near the
vehicle.
CAUTION

 The key (transmitter) may consume
battery power excessively if it
receives high-intensity radio waves.
Do not place the key near electronic
devices such as televisions or
personal computers.
  To avoid damage to the key
(transmitter), DO NOT:
 


 Drop the key.



 Get the key wet.



 Disassemble the key.



 Expose the key to high
temperatures on places such as the
instrument panel or bonnet, under
direct sunlight.
 


 Expose the key to any kind of
magnetic fi eld.




 Place heavy objects on the key.



 Put the key in an ultrasonic
cleaner.
 


 Put any magnetized objects close
to the key.
A code number is stamped on the plate
attached to the key set; detach this plate
and store it in a safe place (not in the
vehicle) for use if you need to make a
replacement key (auxiliary key).
Also write down the code number and
keep it in a separate safe and convenient
place, but not in the vehicle.
If your key (auxiliary key) is lost, consult
your Authorised Mazda Repairer and have
your code number ready.
$9@&;&&%@&EJUJPOJOEC







3–4
Before Driving
Keys
NOTE
  The keyless entry system operation
may vary due to local conditions.
  The keyless entry system is fully
operational (door/liftgate lock/
unlock) when the ignition is switched
off. The system does not operate
if the ignition is switched to any
position other than off.
  If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be dead. To install a new battery,
refer to Key Battery Replacement
(page 6-39 ).
  Battery life is about one year.
Replace the battery with a new one
if the KEY indicator light (green)
fl ashes in the instrument cluster.
Replacing the battery about once
a year is recommended because
the KEY warning light/indicator
light may not illuminate or fl ash
depending on the rate of battery
depletion.
  Additional keys can be obtained at
an Authorised Mazda Repairer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorised Mazda Repairer
when additional keys are required.
Transmitter
Operation buttons Operation indicator light
NOTE
 (European models) The headlights turn on/off by
operating the transmitter. Refer to
Leaving Home Light System on page
4-63 .
 (With theft-deterrent system) The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on
page 3-42 .
  (With the advanced keyless
function (European models))
 The setting can be changed so that a
beep sound is heard for confi rmation
when the doors and liftgate are
locked/unlocked using the key.
(With the advanced keyless
function (Except European
models))
 A beep sound can be heard for
confi rmation when the doors and
liftgate are locked/unlocked using the
key. If you prefer, the beep sound can
be turned off.
 The volume of the beep sound can
also be changed.
 Refer to Personalisation Features on
page 9-13 .
$9@&;&&%@&EJUJPOJOEC







*Some models.3–8
Before Driving
Advanced Keyless Entry System
Advanced Keyless Entry
System
*
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
The advanced keyless function allows you
to lock/unlock the doors and liftgate, or
open the liftgate while carrying the key.
System malfunctions or warnings are
indicated by the following warning lights
or beeps.
 


 KEY Warning Light (Red)
 Refer to Warning/Indicator Lights on
page 4-36 .
 


 Ignition Not Switched Off Warning
Beep
  Refer to Ignition Not Switched Off
(STOP) Warning Beep on page 7-51 .
 


 Key Removed from Vehicle Warning
Beep
  Refer to Key Removed from Vehicle
Warning Beep on page 7-51 .
 


 Request switch Inoperable Warning
Beep
  Refer to Request Switch Inoperable
Warning Beep (With the advanced
keyless function) on page 7-51 .




 Key Left-in-luggage Compartment
Warning Beep
  Refer to Key Left-in-luggage
Compartment Warning Beep (With the
advanced keyless function) on page
7-52 .
 


 Key Left-in-vehicle Warning Beep
 Refer to Key Left-in-vehicle Warning
Beep (With the advanced keyless
function) on page 7-52 .
NOTE
The advanced keyless entry system
functions can be deactivated to prevent
any possible adverse effect on a user
wearing a pacemaker or other medical
device. If the system is deactivated,
you will be unable to start the engine
by carrying the key. Consult an expert
repairer, we recommend an Authorised
Mazda Repairer for details. If the
advanced keyless entry system has been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .
$9@&;&&%@&EJUJPOJOEC







3–9
Before Driving
Advanced Keyless Entry System
Operational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
NOTE
When the battery power is low, or in
places where there are high-intensity
radio waves or noise, the operational
range may become narrower or
the system may not operate. For
determining battery replacement, Refer
to Keyless Entry System on page 3-3 .
Locking, Unlocking the Doors and
the Liftgate
Exterior aerial
Locking only
Operational range80 cm (31in) 80 cm (31in)
NOTE
The system may not operate if you
are too close to the windows or door
handles, or liftgate.
Opening the Liftgate
Exterior aerial
80 cm(31in)
Operational range
$9@&;&&%@&EJUJPOJOEC







*Some models.3–11
Before Driving
Doors and Locks
NOTE
  The vehicle lock-out prevention
feature prevents you from locking
yourself out of the vehicle.
(European models) All doors and the liftgate will
automatically unlock if they are
locked using the power door locks
with any door open.
 If all the doors are closed even
though the liftgate is open, all the
doors will lock.
(Except European models) All doors and the liftgate will
automatically unlock if they are
locked using the power door locks
with any door or the liftgate open.
 
(Door unlock (control) system with
collision detection) *
 This system automatically unlocks
the doors in the event the vehicle
is involved in an accident to allow
passengers to get out of the vehicle
immediately and prevent being
trapped inside. While the ignition
is switched ON and in the event the
vehicle receives an impact strong
enough to infl ate the air bags, all the
doors are automatically unlocked
after about 6 seconds have elapsed
from the time of the accident.
 The doors may not unlock depending
on how an impact is applied, the
force of the impact, and other
conditions of the accident.
 If door-related systems or the battery
is malfunctioning, the doors will not
unlock.
Locking, Unlocking with Key
All doors and the liftgate lock
automatically when the driver's door is
locked using the key. They all unlock
when the driver's door is unlocked using
the key.
Turn the key toward the front to lock,
toward the back to unlock.
LockUnlock
Double Locking System *
The double locking system is designed
to prevent someone who has broken into
your vehicle from opening the door from
the inside.
If you have any problems with the double
locking system, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
$9@&;&&%@&EJUJPOJOEC







*Some models.3–12
Before Driving
Doors and Locks
WARNING
Never activate the double locking
system with passengers, especially
children, still inside the vehicle:
Activating the system with passengers,
especially children, still inside the
vehicle is dangerous. The passengers
cannot open the doors from inside.
They would be trapped and subjected to
extreme temperatures. This could result
in serious injuries or even death.
How to Activate the system
1. Close all the windows and the
sunroof
* .
2. Switch the ignition off and take the key
with you.
3. Close all doors and liftgate.
4. Insert the key in the driver's door, turn
the key to the lock position, and return
it to the centre position. Then turn it
to the lock position again within 3
seconds.
Centre
position
Lock
position
NOTE
  You can also activate the system
by pressing the lock button on the
transmitter twice within 3 seconds.
 (With the advanced keyless
function)
 You can also activate the system by
pressing the request switch twice
within 3 seconds.
5. The indicator light illuminates for
about 3 seconds to indicate that the
system has been activated.
NOTE
The system cannot be activated when
any door or the liftgate is open.
How to Deactivate the System
Unlock the driver's door or switch the
ignition ON.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the system can only be deactivated by
unlocking a door with the key.
$9@&;&&%@&EJUJPOJOEC







3–21
Before Driving
Doors and Locks
NOTE
 

 When the liftgate latch is released by
pressing the electric liftgate opener,
the liftgate raises slightly to allow
it to be opened. If the liftgate is not
operated for a certain period of time
after the electric liftgate opener has
been pressed, the liftgate cannot be
raised any more from its slightly
raised position. Press the electric
liftgate opener again to fully open
the liftgate. To close the liftgate from
its slightly raised position, open it
fi rst by pressing the electric liftgate
opener, and waiting for 1 second or
longer then close it.
 If the liftgate is not fully closed,
the driver is notifi ed by a warning
indicated in the instrument cluster.
 
 If the vehicle battery is dead or there
is a malfunction in the electrical
system and the liftgate cannot be
unlocked, the liftgate can be opened
by performing the emergency
procedure.
 Refer to When Liftgate Cannot be
Opened on page 7-55 .
Closing the liftgate
CAUTION
When closing the liftgate, return the
luggage board to its original position.
If the liftgate is closed with the luggage
board standing upright, the luggage
compartment cover could be damaged.
Luggage compartment cover
Luggage board
Lower the liftgate slowly using the liftgate
grip recess, then push the liftgate closed
using both hands.
Do not slam it. Pull up on the liftgate to
make sure it is secure.
Liftgate grip recess
$9@&;&&%@&EJUJPOJOEC







3–35
Before Driving
Windows
Auto-opening/closing
To fully open the window automatically,
press the switch completely down, then
release. The window will fully open
automatically.
To fully close the window automatically,
pull the switch completely up, then
release. The window will fully close
automatically.
To stop the window partway, pull or press
the switch in the opposite direction and
then release it.
Power window system initialization
procedure
If the battery was disconnected during
vehicle maintenance, or for other reasons
(such as a switch continues to be operated
after the window is fully open/closed),
the window will not fully open and close
automatically.
The power window auto function will only
resume on a power window that has been
reset.
1. Switch the ignition ON.
2. Make sure that the power window lock
switch located on the driver's door is
not depressed.
3. Press the switch and fully open the
window.
4. Pull up the switch to fully close the
window and continue holding the
switch for about 2 seconds after the
window fully closed. Jam-safe window
If a person's hands, head or an object
blocks the window during the auto-closing
operation, the window will stop and open
halfway.
WARNING
Make sure nothing blocks the window
just before it reaches the fully closed
position or while holding up the power
window switch:
Blocking the power window just before
it reaches the fully closed position or
while holding up the power window
switch is dangerous.
In this case, the jam-safe function
cannot prevent the window from
closing all the way. If fi ngers are
caught, serious injuries could occur.
NOTE
  Depending on driving conditions, a
closing power window could stop
and start opening when the window
feels a shock that is similar to
something blocking it.
 In the event the jam-safe function
activates and the power window
cannot be closed automatically, pull
and hold the switch and the window
will close.
  The jam-safe window function does
not operate until the system has been
reset.
$9@&;&&%@&EJUJPOJOEC