turn signal MAZDA MODEL CX-3 2017 (in English) Owner's Manual

5–17
Interior Features
Audio System
Strong signal noise
This occurs very close to a transmitter
tower. The broadcast signals are extremely
strong, so the result is noise and sound
breakup at the radio receiver.


Station drift noise
When a vehicle reaches the area of two
strong stations broadcasting at similar
frequencies, the original station may be
temporarily lost and the second station
picked up. At this time there will be some
noise from this disturbance.

Station 2
88.3 MHz Station 1
88.1 MHz

Operating Tips for CD Player
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in
the CD player may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded optical
components will clear naturally in about
an hour. Wait for normal operation to
return before attempting to use the unit.
Handling the CD player
The following precautions should be
observed.
 


y Do not use deformed or cracked CDs.
The disc may not eject resulting in a
malfunction.

 


y Do not use non-conventional discs such
as heart-shaped, octagonal discs, etc.
The disc may not eject resulting in a
malfunction.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–28
Interior Features
Audio System
Operating the Radio
Band selector buttonChannel preset buttons
Scan button
Auto memory button
Tuning buttonAudio display

R a d i o O N
Press a band selector button (
) to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1
:FM2
:AM.

The selected mode will be indicated.
N O T E
If the FM broadcast signal becomes weak,
reception automatically changes from
STEREO to MONO for reduced noise.

Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Select the station by pressing the tuning
button (
, ) lightly. Seek tuning
Automatic search for radio stations starts
when the tuning button (
, ) is pressed
until a beep sound is heard. The search
stops when a station is found.
N O T E
If you continue to press and hold the
button, the frequency will continue
changing without stopping.

Scan tuning
Press and hold the scan button (
) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, press and hold
the scan button (
) again during this
interval.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–45
Interior Features
Audio System
N O T E
 


y If an analog broadcast is received once
and
is received while HD1 is
selected, the audio unit switches to the

station automatically.
 


y When the icon is illuminated, there
could be a noticeable difference in
sound quality and volume when a
change from digital to analog signals
occurs. If the sound quality and volume
become noticeably diminished or cut
off, select the
icon to turn off

( icon is not illuminated). 


y Once an analog broadcast is received
when HD1 is selected from the Favorite
channels, it is switched to

automatically. If the radio reception
conditions are poor, or HD is off,
switching to
broadcasts is
not possible.
 


y When an HD specialty channel (HD2 to
HD8) is selected from the Favorite
channels, “Signal Lost” is displayed
and no audio is output until

is received. If the radio reception
conditions are poor, “Signal Lost”
continues to be displayed.
 


y If the icon is not illuminated,
information such as song titles of the

station are received,
however, the audio output is analog.

iTunes Tagging (for Apple devices with
USB use only)
By tagging a song currently being aired,
the song can be easily purchased from the
iTunes Store. Up to 100 tags can be stored.

1. Select the icon. The tag is stored in
the audio unit.
2. Connect the device via USB. The
tag is sent to the connected device
automatically.
3. Synchronize the device with iTunes.
The tagged song can now be purchased
from the iTunes Store.

N O T E
 


y Both AM and FM can be
used.
 


y Because iTunes tagging only supports
purchases from the iTunes Store, direct
downloading of music from the vehicle's
audio unit is not possible.
 


y If the available memory for the
connected device is insuf¿ cient, the tag
is not sent.
 


y If an error occurs while the tag is being
sent, reconnect the device.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–46
Maintenance and Care
Owner Maintenance
Light Bulbs

With LED Headlights
With Halogen Headlights
Overhead lights (Front)/Map lights
Overhead lights (Rear)Overhead lights (Front)/Map lights
Headlights (High beam)/
Daytime running lights Headlights (Low beam)
Daytime running lights/
Parking lightsSide turn signal lights
Fog lights
Front side-marker lights/
Parking lights Front side-marker lights/
Parking lights
Front turn signal lights
Luggage compartment light
License plate lights
Reverse lights
Taillights Rear turn signal lights Rear side-marker lights
Brake lights/TaillightsHigh-mount brake light
Some models.
Side turn signal lights
Headlights (High beam) Headlights (Low beam)
Fog lights
Front turn signal lights

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–49
Maintenance and Care
Owner Maintenance
Daytime running lights/Parking lights/
Front side-marker lights (With LED
headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front side-marker lights/Parking lights
(With halogen headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.



4. Install the new bulb in the reverse order
of the removal procedure.

Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.



3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.



5. Install the new bulb in the reverse order
of the removal procedure.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–50
Maintenance and Care
Owner Maintenance
*Some models.
Fog lights * , Side turn signal lights * ,
Brake lights/Taillights (With LED
headlights), Rear side-marker lights
(With LED headlights),Taillights (With
LED headlights), High-mount brake
light
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Rear turn signal lights, Brake lights/
Taillights (With halogen headlights),
Rear side-marker lights (With halogen
headlights)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the bolts counterclockwise and
remove them.


3. Pull the unit rearward to remove it.



4. Turn the socket and bulb assembly
counterclockwise and remove it.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–51
Maintenance and Care
Owner Maintenance
5. Disconnect the bulb from the socket.
Rear turn signal lights



Brake lights/Taillights



Rear side-marker lights



6. Install the new bulb in the reverse order
of the removal procedure.

Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.



3. Turn the socket and bulb assembly
counterclockwise and remove it.
4. Disconnect the bulb from the socket.



5. Install the new bulb in the reverse order
of the removal procedure.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–57
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
16 AT PUMP 15 A Transaxle control system
*
17 AT 15 A Transaxle control system *
18 D.LOCK 25 A Power door locks
19 H/L RH 20 A Headlight (RH)
20

7.5 A Engine control system
21 TAIL 20 A Taillights, License plate lights, Parking lights
22 — — —
23 ROOM 25 A Overhead light
24 FOG 15 A Fog lights
*
25 H/CLEAN 20 A —
26 STOP 10 A Brake lights
27 HORN 15 A Horn
28 H/L LH 20 A Headlight (LH)
29 ABS/DSC S 30 A ABS, Dynamic stability control system
*
30 HAZARD 15 A Hazard warning À ashers, Turn signal lights
31 FUEL PUMP 15 A Fuel system
32 FUEL WARM 25 A —
33 WIPER 20 A Front window wiper
34

50 A For protection of various circuits
35 FAN2 30 A —
36 FUEL PUMP 30 A —
37 ABS/DSC M 50 A ABS, Dynamic stability control system
*
38 EVVT 20 A Engine control system *
39 — — —
40 FAN1 30 A —
41 FAN3 40 A Cooling fan
42 ENG.MAIN 40 A Engine control system
43 EPS 60 A —
44 DEFOG 40 A Rear window defogger
45 IG2 30 A For protection of various circuits
46 INJECTOR 30 A Engine control system
47 HEATER 40 A Air conditioner
48 P.WINDOW1 30 A Power windows
49 DCDC DE 40 A —

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–2
If Trouble Arises
Parking in an Emergency
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.



The hazard warning lights warn other
drivers that your vehicle is a traf¿ c hazard
and that they must take extreme caution
when near it.



Depress the hazard warning À asher and
all the turn signals will À ash. The hazard
warning indicator lights in the instrument
cluster À ash simultaneously.
N O T E




y The turn signals do not work when the
hazard warning lights are on.
 


y Check local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–27
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
If a Warning Light Turns On or Flashes
If any warning light turns on/À ashes, take appropriate action for each light. There is no
problem if the light turns off, however if the light does not turn off or turns on/À ashes again,
consult an Authorized Mazda Dealer.
(Vehicles with type B audio)
The warning contents can be veri¿ ed on the audio.

1. Select the icon on the home screen to display the applications screen.
2. Select the “Warning Guidance”.

Stop Vehicle in Safe Place Immediately
If any of the following warning lights turns on, the system may have a malfunction. Stop the
vehicle in a safe place immediately and contact an Authorized Mazda Dealer.

Signal Warning


Brake System Warning
Light
This warning has the following functions:
Parking brake warning/Warning light inspection
The light illuminates when the parking brake is applied with the ignition switched to
START or ON. It turns off when the parking brake is fully released.
Low brake À uid level warning
If the brake warning light remains illuminated even though the parking brake is
released, the brake À uid may be low or there could be a problem with the brake system.
Park the vehicle in a safe place immediately and contact an Authorized Mazda Dealer.
WARNING
Do not drive with the brake system warning light illuminated. Contact an
Authorized Mazda Dealer to have the brakes inspected as soon as possible:
Driving with the brake system warning light illuminated is dangerous. It indicates
that your brakes may not work at all or that they could completely fail at any
time. If this light remains illuminated, after checking that the parking brake is fully
released, have the brakes inspected immediately.
CAUTION
In addition, the eff ectiveness of the braking may diminish so you may need to
depress the brake pedal more strongly than normal to stop the vehicle.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD