MAZDA MODEL CX-3 2017 Owners Manual (in English)

7–7
If Trouble Arises
Flat Tire
CAUTION
 


¾ When using the temporary spare tire,
driving stability may decrease compared
to when using only the conventional tire.
Drive carefully.
 


¾ To avoid damage to the temporary
spare tire or to the vehicle, observe the
following precautions:
 


¾ Do not exceed 80 km/h (50 mph).



¾ Avoid driving over obstacles. Also, do
not drive through an automatic car
wash. This tire's diameter is smaller
than a conventional tire, so the
ground clearance is reduced.
 


¾ Do not use a tire chain on this tire
because it will not fi t properly.
 


¾ Do not use your temporary spare
tire on any other vehicle, it has been
designed only for your Mazda.
 


¾ Use only one temporary spare tire on
your vehicle at the same time.


To remove the spare tire
1 . (With luggage board)
Lift up the luggage board.
2. (With luggage board)
Pull the luggage board outward a
little and insert the opposite end into
the holders so that the luggage board
stands.


Luggage board
Holders

3. Lift the luggage mat.


Luggage mat

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–8
If Trouble Arises
Flat Tire
4. For vehicles equipped with a sub-
woofer, uncouple the connector.


Connector
N O T E
Extra strength may be required to
uncouple the connector. Be sure to squeeze
the tab ¿ rmly.

5. For vehicles equipped with a sub-
woofer, loosen the hold-down bolt and
remove the woofer and spare tire.



For vehicles not equipped with a sub-
woofer, turn the spare tire hold-down
bolt counterclockwise and remove the
spare tire.


Spare tire hold-down bolt

To secure the spare tire
Store the spare tire in the reverse order
of removal. After storing, verify that the
spare tire is stored securely.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–9
If Trouble Arises
Flat Tire
Changing a Flat Tire
N O T E
If the following occurs while driving, it
could indicate a À at tire.




y Steering becomes dif¿ cult.



y The vehicle begins to vibrate
excessively.
 


y The vehicle pulls in one direction.
If you have a À at tire, drive slowly to a
level spot that is well off the road and out
of the way of traf¿ c to change the tire.
Stopping in traf¿ c or on the shoulder of a
busy road is dangerous.
WARNING
Be sure to follow the directions for
changing a tire:
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure someone.
No person should place any portion
of their body under a vehicle that is
supported by a jack.

Never allow anyone inside a vehicle
supported by a jack:
Allowing someone to remain in
a vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.

N O T E
Make sure the jack is well lubricated
before using it.

1. Park on a level surface off the right-of-
way and ¿ rmly set the parking brake.
2. Shift into Park (P) and turn off the
engine.
3. Turn on the hazard warning À asher.
4. Have everyone get out of the vehicle
and away from the vehicle and traf¿ c.
5. Remove the jack, tool, and spare tire
(page 7-3 ).
6. Block the wheel diagonally opposite
the À at tire. When blocking a wheel,
place a tire block both in front and
behind the tire.


N O T E
When blocking a tire, use rocks or wood
blocks of suf¿ cient size if possible to hold
the tire in place.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–10
If Trouble Arises
Flat Tire
Removing a Flat Tire
1. If your vehicle is equipped with a
wheel cover, pry off the wheel cover
with the beveled end of the jack lever.



N O T E
Force the end of the jack lever ¿ rmly
between wheel and cover, or removal will
be dif¿ cult.

CAUTION
Align the notch on the wheel cover
with the valve stem when installing it.


Tire valve Notch

Damage could occur during
installation if the wheel cover is not
properly aligned.

2. Loosen the lug nuts by turning them
counterclockwise one turn each, but do
not remove any lug nuts until the tire
has been raised off the ground.



3. Place the jack on the ground.
4. Turn the jack screw in the direction
shown in the ¿ gure and adjust the jack
head so that it is close to the jack-up
position.


Jack head

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–11
If Trouble Arises
Flat Tire
5. Place the jack under the jack-up
position closest to the tire being
changed with the jack head squarely
under the jack-up point.


Jacking position

6. Continue raising the jack head
gradually by rotating the screw with
your hand until the jack head is inserted
into the jack-up position.


Tire blocks
Jacking position

WARNING
Use only the front and rear jacking
positions recommended in this manual:
Attempting to jack the vehicle
in positions other than those
recommended in this manual is
dangerous. The vehicle could slip off
the jack and seriously injure or even kill
someone. Use only the front and rear
jacking positions recommended in this
manual.

Do not jack up the vehicle in a position
other than the designated jack-up
position or place any objects on or
under the jack:
Jacking up the vehicle in a position
other than the designated jack-up
position or placing objects on or
under the jack is dangerous as it could
deform the vehicle body or the vehicle
could fall off the jack resulting in an
accident.

Use only the jack provided with your
Mazda:
Using a jack that is not designed for
your Mazda is dangerous. The vehicle
could slip off the jack and seriously
injure someone.

Never place objects under the jack:
Jacking the vehicle with an object
under the jack is dangerous. The jack
could slip and someone could be
seriously injured by the jack or the
falling vehicle.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–12
If Trouble Arises
Flat Tire
7. Insert the jack lever and attach the lug
wrench to tire jack.



8. Turn the jack handle clockwise and
raise the vehicle high enough so that
the spare tire can be installed. Before
removing the lug nuts, make sure your
Mazda is ¿ rmly in position and that it
cannot slip or move.



WARNING
Do not jack up the vehicle higher than is
necessary:
Jacking up the vehicle higher than
is necessary is dangerous as it could
destabilize the vehicle resulting in an
accident.

Do not start the engine or shake the
vehicle while it is jacked up:
Starting the engine or shaking
the vehicle while it is jacked up is
dangerous as it could cause the vehicle
to fall off the jack resulting in an
accident.

Never go under the vehicle while it is
jacked up:
Going under the vehicle while it is
jacked up is dangerous as it could
result in death or serious injury if the
vehicle were to fall off the jack.

9. Remove the lug nuts by turning them
counterclockwise; then remove the
wheel and center cap.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–13
If Trouble Arises
Flat Tire
*Some models.
Locking Lug Nuts *
If your vehicle has Mazda optional
antitheft wheel lug nuts, one on each
wheel will lock the tires and you must
use a special key to unlock them. This
key will attach to the lug wrench.
Register them with the lock manufacturer
by ¿ lling out the card provided in the
glove compartment and mailing it in the
accompanying envelope. If you lose this
key, consult an Authorized Mazda Dealer
or use the lock manufacturer's order form,
which is with the registration card.
Accessory wheel locks cannot be used on
steel wheels. This includes situations when
the spare tire is installed. If the spare tire
is installed, one of the original lug nuts
(which should still be in the vehicle) must
be installed in place of the wheel lock.

Special key Antitheft lug nut

To remove an antitheft lug nut
1. Obtain the special key for the antitheft
lug nut.
2. Place the special key on top of the
antitheft lug nut, and be sure to hold
the key square to it. If you hold the key
at an angle, you may damage both key
and nut. Do not use a power impact
wrench.
3. Place the lug wrench on top of the key
and apply pressure. Turn the wrench
counterclockwise.

To install the antitheft lug nut
1. Place the special key on top of the nut,
and be sure to hold the key square to
it. If you hold the key at an angle, you
may damage both key and nut. Do not
use a power impact wrench.
2. Place the lug wrench on top of the
special key, apply pressure, and turn it
clockwise.

Nut tightening torque
N·m (kgf·m, ft·lbf) 108—147 (12—14, 80—108)

Mounting the Spare Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.



%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–14
If Trouble Arises
Flat Tire
WARNING
Make sure the mounting surfaces of
the wheel, hub and lug nuts are clean
before changing or replacing tires:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off , resulting in
an accident.

2. Mount the spare tire.
3. Install the lug nuts with the beveled
edge inward; tighten them by hand.



WARNING
Do not apply oil or grease to lug nuts
and bolts and do not tighten the
lug nuts beyond the recommended
tightening torque:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the tire
to come off , resulting in an accident.
In addition, lug nuts and bolts could
be damaged if tightened more than
necessary.

4. Turn the lug wrench counterclockwise
and lower the vehicle. 5. Use the lug wrench to tighten the nuts
in the order shown.



If you are unsure of how tight the nuts
should be, have them inspected at an
Authorized Mazda Dealer.

Nut tightening torque
N·m (kgf·m, ft·lbf) 108—147 (12—14, 80—108)

WARNING
Always securely and correctly tighten
the lug nuts:
Improperly or loosely tightened lug
nuts are dangerous. The wheel could
wobble or come off . This could result
in loss of vehicle control and cause a
serious accident.

Be sure to reinstall the same nuts you
removed or replace them with metric
nuts of the same confi guration:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip off
and cause an accident.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–15
If Trouble Arises
Flat Tire
6. (Without À at tire belt)
Store the damaged tire in the luggage
compartment.
(With À at tire belt)
Remove the luggage compartment
cover (if equipped).
Refer to Luggage Compartment on
page 3-22 .


Strap



Pin
Pin

7. Remove the belt for securing the À at
tire. 8. (With luggage board)
Pull the luggage board outward and
place it on top of the luggage mat.


Luggage board
Luggage mat


Luggage mat
Luggage board
9. Remove the center cap by tapping it
with the lug wrench.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–16
If Trouble Arises
Flat Tire
10. Thread the belt through the rear seat as
shown in the ¿ gure.






11. Place the À at tire in the luggage
compartment.


12. Thread the buckle through the wheel as
shown in the ¿ gure.



13. Thread the belt through the buckle
while pressing the tire to the seatback.



14. Pull the belt end to secure the À at tire.



%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD