display MAZDA MODEL CX-30 2019 Owners Manual (in English)

1. Drive to the side of the road and
park off the right-of-way on level
ground.
2. Turn off the engine and wait 5
minutes for the oil to drain back
into the sump.
3. Inspect the engine oil level (page
6-27). If it's low, add the
appropriate amount of engine oil
while being careful not to overfill.
CAUTION
Do not run the engine if the oil
level is low. Otherwise, it could
result in extensive engine damage.
4. Start the engine and check the
warning light.

If the light remains illuminated even
though the oil level is normal or after
adding oil, stop the engine
immediately and have your vehicle
towed to an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼High Engine Coolant Temperature
Warning Indication
Displays if the engine coolant
temperature has increased excessively.
“Elevated Engine Coolant Temp. Drive
Slowly” displayed
Drive slowly to reduce engine load
until you can find a safe place to stop
the vehicle and wait for the engine to
cool down.
“Excessive Engine Coolant Temp. Stop
the Vehicle in a Safe Location”
displayed
This indicates the possibility of
overheating. Park the vehicle in a safe
place immediately and stop the
engine.
Refer to Overheating on page 7-44.
CAUTION
Do not drive the vehicle with the high
engine coolant temperature warning
light illuminated. Otherwise, it could
result in damage to the engine.
▼Power Steering Malfunction
Indication/Indicator Light
The message is displayed if the electric
power steering has a malfunction.
If the message is displayed, stop the
vehicle in a safe place and do not
operate the steering wheel. There is no
problem if the indication turns off
when the engine is restarted after
some time has passed. If the indication
displays even after the engine is
restarted, contact an expert repairer
(we recommend an Authorised Mazda
Repairer) if the message is displayed
continuously.
NOTE
xIf the message is displayed, the
power steering will not operate
normally. In this case, the steering
wheel can still be operated,
however, the operation may feel
heavy compared to normal, or the
steering wheel could vibrate when
turning.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-51

xRepeatedly jerking the steering
wheel left and right while the vehicle
is stopped or moving extremely
slowly will cause the power steering
system to go into protective mode
which will make the steering feel
heavy, but this does not indicate a
problem. If this occurs, park the
vehicle safely and wait several
minutes for the system to return to
normal.
▼ABS Warning Indication/Warning
Light
If the ABS warning light stays on while
you're driving , the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
NOTE
xWhen the engine is jump-started to
charge the battery, uneven rpm
occurs and the ABS warning light
may illuminate. If this occurs, it is the
result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.
xThe brake assist system does not
operate while the ABS warning light
is illuminated.
▼Master Warning Indication
The indication displays if the system
has a malfunction.
Check the reason for the indication
displaying on the centre display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
▼Brake Control System Warning
Indication/Warning Light (Amber)
The warning light illuminates when the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼Electric Parking Brake (EPB)
Indication/Indicator Light
This warning has the following
functions:
Parking brake warning/Indicator light
inspection
The light illuminates when the parking
brake is applied with the ignition
switched to START or ON. It turns
off
when the parking brake is released.
When the light is
flashing
The light flashes if the Electric Parking
Brake (EPB) has a malfunction. If the
light remains flashing even if the
Electric Parking Brake (EPB) switch is
operated, consult an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-52

▼Brake Override Warning Indication
This message is displayed when the
accelerator pedal and brake pedal are
depressed at the same time while
driving.
Release the accelerator pedal and
depress the brake pedal.
▼Check Engine Indication/Light
If this light illuminates while driving ,
the vehicle may have a problem. It is
important to note the driving
conditions when the light illuminated
and consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
The check engine light may illuminate
in the following cases:
xThe engine's electrical system has a
problem.
xThe emission control system has a
problem.
x(Except SKYACTIV-D 1.8)
xThe fuel tank level being very low
or approaching empty.
xThe
fuel-filler cap is missing or not
tightened securely.
If the check engine light remains on, or
it flashes continuously , do not drive at
high speeds and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
WARNING
If the check engine light turns on, do
not disconnect the battery leads.
If the battery leads are disconnected
and then reconnected, the engine
could be damaged and catch on
fire.
▼i-stop Warning Indication/
Warning Light (Amber)*
When the light is turned on
xA problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when
the ignition is switched ON.
x(Except European model)
If the i-stop warning light (amber)
remains on while the engine is
running , the battery performance
may have decreased. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-53

▼Petrol Particulate Filter Warning
Indication/Warning Light
(SKYACTIV-X 2.0)
“Excessive Soot Levels in Filter. Drive
Until Warning Light Turns
Off” is
displayed/When the light is turned on
The particulate matter (PM) cannot be
removed automatically and the
amount of collected PM reaches a
specified amount.
After the engine has sufficiently
warmed up (engine coolant
temperature of 80 °C (176 °F) or
more), depress the accelerator pedal
and drive the vehicle at a speed of 20
km/h (12 mph) or more for about 30
minutes to eliminate the PM.
“Abnormal Soot Levels in Filter. Have
the Vehicle Inspected.” is displayed/
When the light is
flashing
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
CAUTION
If the vehicle is continually driven as
usual with the petrol particulate filter
warning light illuminated, PM increases
and the warning light may start
flashing. If the petrol particulate filter
warning light starts flashing, have the
vehicle inspected immediately at an
expert repairer (we recommend an
Authorised Mazda Repairer). If the
vehicle is not inspected and continues
to be driven, the engine may
malfunction.
NOTE
xWhen the petrol particulate filter
warning light flashes, the engine
output is restricted to protect the
petrol particulate filter.
xThe engine sound and exhaust gas
smell may change when PM is being
removed while driving.
▼Diesel Particulate Filter Warning
Indication/Warning Light
(SKYACTIV-D 1.8)
“Excessive Soot Levels in Filter. Drive
Until Warning Light Turns Off” is
displayed/When the light is turned on
The particulate matter (PM) cannot be
removed automatically and the
amount of collected PM reaches a
specified amount.
After the engine has sufficiently
warmed up (engine coolant
temperature of 80 °C (176 °F) or
more), depress the accelerator pedal
and drive the vehicle at a speed of 15
km/h (9.3 mph) or more for about 15
to 20 minutes to eliminate the PM.
“Abnormal Soot Levels in Filter. Have
the Vehicle Inspected” is displayed/
When the light is flashing
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-54

▼KEY Warning Indication/Warning
Light (Red)
“Keyless Entry System Malfunc. Have
the Vehicle Inspected” is displayed
This message is displayed if the
advanced keyless entry & push button
start system has a problem.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
CAUTION
If the message is indicated, or the push
button start indicator light (amber)
flashes, the engine may not start. If the
engine cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-9.
“Key Not Detected” is displayed
xIf the presence of the key cannot be
detected (dead battery, battery
malfunction, no key), it is displayed
when the driver attempts to start the
engine (push button start operation,
brake pedal depression).
xDisplayed when it is determined that
a key that was in the vehicle has
been removed from the vehicle. (Key
taken out warning. Other than
IG-OFF).
▼Security Indicator Light
If the security indicator light flashes
continuously while you are driving, do
not shut
off the engine. Go to an
expert repairer (we recommend an
Authorised Mazda Repairer) and have
it checked. If the engine is shut off
while the indicator light is
flashing , you
will not be able to restart it.
Make sure the key is within the
operational range for signal
transmission. Switch the ignition off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
NOTE
Because the electronic codes are reset
when the immobilizer system is
repaired, the keys are needed. Make
sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
▼AWD Warning Indication/
Warning Light*
“AWD Malfunction. Front Wheel
Drive Only. Have the Vehicle
Inspected” is displayed/When the
light is turned on
The indication is displayed/the light
turns on under the following
conditions. The system may have a
malfunction. Have the vehicle checked
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-56*Some models.

at an expert repairer (we recommend
an Authorised Mazda Repairer).
xWhen there is a malfunction in the
AWD system.
“Excessive AWD System Load. Drive
Slowly Until Warning Light Turns Off.
Vehicle Now in Front Wheel Drive” is
displayed/When the light is flashing
The indication is displayed/the light
flashes under the following conditions.
Park the vehicle in a safe place and
check that the warning indication light
turns
off/ the warning light stops
flashing, and then drive the vehicle.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer) if the indication is
continuously displayed.
xWhen the differential oil temperature
is excessively high.
xWhen there is a large difference
between the front and rear wheel
rotation, such as when trying to
remove the vehicle from mud.
“Mismatched Tyre Diameters. Vehicle
Now in Front Wheel Drive” is
displayed/When the light is turned on
The indication is displayed/the light
turns on under the following
conditions. Inspect the tyre sizes or
tyre pressures on all 4 wheels. Contact
an expert repairer (we recommend an
Authorised Mazda Repairer) if the
indication remains on or the warning
light remains illuminated.
xWhen any of the tyre diameter is
different.
xWhen any of the tyre pressure is
incorrect.
▼120 km/h Warning Light*
The 120 km/h warning light
illuminates when the vehicle speed
exceeds 120 km/h.
Action to be taken
Lower the vehicle speed.
▼Tyre Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Flashing)
*
If there is a problem with the TPMS or
the voltage of a tyre pressure sensor
decreases, the TPMS warning light
flashes and a message is displayed on
the multi-information display. Have
your vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or
flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-57

Do not ignore the TPMS warning light
when it is turned on or flashing:
Continuing to drive the vehicle while
ignoring the illumination/flashing of
the TPMS warning light is dangerous
because a tyre may burst which could
lead to an accident. Take appropriate
measures as soon as possible.
▼High Beam Control System (HBC)
Warning Indication/Warning Light
(Amber)
*
The light remains turned on if there is a
problem with the system. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼Adaptive LED Headlights (ALH)
Warning Indication/Warning Light
(Amber)
*
The light remains turned on if there is a
problem with the system. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼i-ACTIVSENSE Warning
Indication/Warning Light*
The indication displays if the system
has a malfunction.
Check the reason for the indication
displaying on the centre display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
▼Exterior Light Warning Indication/
Warning Light
This light illuminates if there is a
malfunction in the exterior lights
(except number plate lights). Have
your vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
CAUTION
Do not drive the vehicle while an
exterior light has a malfunction. Poor
visibility, and not being able to signal
braking and turns may cause an
accident. In addition, if the vehicle is
driven with the lights not turned on, it
may conflict with laws and regulations
due to poor maintenance.
▼Low Fuel Warning Indication/
Warning Light
The light turns on when the remaining
fuel is about 9.0 L (2.3 US gal, 1.9 Imp
gal). If you continue to drive after the
light turns on without refuelling and
the fuel gauge reaches nearly empty,
the light flashes.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-58*Some models.

NOTE
The light illumination timing may vary
because fuel inside the fuel tank moves
around according to the driving
conditions and the vehicle posture.
Action to be taken
Add fuel. If the light is flashing, refuel
as soon as possible.
▼Engine Oil Level Warning
Indication/Warning Light
This warning light indicates that the
engine oil level is around the MIN
mark (page 6-27).
CAUTION
Do not continue to drive the vehicle
with the engine oil level warning
indication/warning light displayed/
turned on. If the vehicle continues to
be driven with an insufficient amount
of engine oil, it could cause damage to
the engine.
Action to be taken
Add 1 L (0.3 US gal, 0.2 Imp gal) of
engine oil (page 6-24).
▼Seat Belt Warning Indication/
Warning Light (Front seat)
The seat belt warning light turns on if
the driver or front passenger's seat is
occupied and the seat belt is not
fastened with the ignition switched
ON.
If the driver or front passenger's seat
belt is unfastened (only when the front
passenger's seat is occupied) and the
vehicle is driven at a speed faster than
about 20 km/h (12 mph), the warning
light flashes. After a short time, the
warning light stops flashing, but
remains illuminated. If a seat belt
remains unfastened, the warning light
flashes again for a given period of
time.
NOTE
xIf the driver or front passenger's seat
belt is unfastened after the warning
light turns on, and the vehicle speed
exceeds 20 km/h (12 mph), the
warning light flashes again.
xPlacing heavy items on the front
passenger's seat may cause the front
passenger's seat belt warning
function to operate depending on
the weight of the item.
xTo allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger's
seat. The sensor may not function
properly because the additional seat
cushion could cause sensor
interference.
xIf a small child is seated on the front
passenger's seat, the warning light
may not operate.
Action to be taken
Fasten the seat belts.
▼Seat Belt Warning Light (Rear seat)
(Red)
If the rear seat belts are not fastened
while the ignition is switched ON , the
driver and the passenger are alerted by
the warning light.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-59

The warning light operates even if there
is no passenger on the rear seat.
NOTE
If a rear seat belt is not fastened by a
certain period of time after the engine
has been started, the warning light
turns
off.
Action to be taken
Fasten the seat belts.
▼Low Washer Fluid Level Warning
Indication/Warning Light*
This warning light indicates that little
washer fluid remains.
Action to be taken
Add washer fluid (page 6-31).
▼Door-Ajar/Liftgate-Ajar Warning
Indication/Warning Light
The light turns on if any door/liftgate is
not closed securely.
Action to be taken
Close the door/liftgate securely.
▼Tyre Pressure Monitoring System
(TPMS) Warning Indication/
Warning Light (Turns on)
*
If a tyre pressure decreases below the
specified air pressure, the TPMS
warning light turns on.
At the same time, a message and the
tyre pressure of each tyre are displayed
on the multi-information display
alternately. In addition, the tyre (s)
with low air pressure is displayed in
yellow.
WARNING
Do not drive the vehicle at high
speeds if the TPMS warning light turns
on or flashes:
Driving the vehicle at high speeds
while the TPMS warning light is turned
on or flashing is dangerous because
the brake performance and the
steering wheel operability will be
reduced. If the vehicle is driven at high
speeds or the brakes are suddenly
applied, it could lead to an accident.
Gradually apply the brakes to lower the
vehicle's speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-60*Some models.

Do not ignore the TPMS warning light
when it is turned on or flashing:
Continuing to drive the vehicle while
ignoring the illumination/flashing of
the TPMS warning light is dangerous
because a tyre may burst which could
lead to an accident. Take appropriate
measures as soon as possible.
NOTE
While the TPMS is learning the tyre
positions, such as immediately after a
tyre position has been changed, the
tyre pressure at the tyre position prior
to it being changed is displayed until
the system completes the learning. For
this reason, the tyre pressures
displayed for the tyre positions may be
different from the actual tyre pressures
at the tyre positions.
Action to be taken
Adjust the tyre pressures to the
appropriate pressures.
Refer to Tyre Inflation Pressure on page
6-41.
CAUTION
¾Adjust the tyre pressures while the
tyres are cool. Because the air
pressure in the tyres fluctuates
depending on the temperature,
before adjusting the tyre pressures,
let the vehicle sit for an hour or drive
it only within a 1.6 km (1 mile)
distance. If the tyre pressures are
adjusted while the tyres are warm,
the tyre pressures may decrease
below the specified air pressure after
cooling down which could turn on
the warning light. In addition,
because the air pressure in the tyres
decreases when the ambient
temperature is low, if the ambient
temperature increases, an
illuminated TPMS warning light may
turn off. Under any circumstances,
always adjust the tyre pressures while
the tyres are cool.
¾After adjusting the tyre pressures, the
TPMS warning light turns off. If the
TPMS warning light does not turn
off,
drive the vehicle at a speed of about
25 km (16 mph) or faster for 3
minutes or longer and make sure the
warning light turns off.
If the TPMS warning light remains on
even after adjusting the tyre pressures,
one of the tyres may have a puncture.
▼KEY Indicator Light (Green)
(Flashing)
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-61