clutch MAZDA MODEL CX-30 2019 Owners Manual (in English)

Ignition Switch
▼Push Button Start Positions
The system operates only when the key
is within operational range.
Each time the push button start is
pressed, the ignition switches in the
order of
off, ACC, and ON. Pressing
the push button start again from ON
switches the ignition
off.
1. Indicator light
2. Push button start
NOTE
xThe engine starts by pressing the
push button start while depressing
the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission). To switch
the ignition position, press the push
button start without depressing the
pedal.
xDo not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transmission,
the selector lever is in the P position,
and the ignition is in ACC), the
ignition switches off automatically
after about 25 minutes.
Off
The power supply to electrical devices
turns off and the indicator light
(amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat,
always switch the ignition off, set the
parking brake, and make sure the
selector lever is in P (automatic
transmission) position or in 1st gear
or R (manual transmission):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transmission)
position or to 1st gear or R (manual
transmission) is dangerous.
Unexpected vehicle movement could
occur which could result in an
accident.
In addition, if your intention is to leave
the vehicle for even a short period, it is
important to switch the ignition
off, as
leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is
flashing , a message is
displayed on the multi-information,
and the beep sound is heard, this
indicates that the steering wheel is not
unlocked. To unlock the steering
wheel, press the push button start
while moving the steering wheel left
and right.
When Driving
Start/Stop Engine
4-4

This is for improved exhaust gas
purification and does not indicate
any parts defect.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Continue to depress the brake
pedal firmly until the engine has
completely started.
5.(Manual transmission)
Continue to depress the clutch
pedal firmly until the engine has
completely started.
(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
NOTE
x(Manual transmission)
The starter will not operate if the
clutch pedal is not depressed
sufficiently.
x(Automatic transmission)
The starter will not operate if the
selector lever is not in P or N
position and the brake pedal is
not depressed sufficiently.
6. Make sure that the push button
start indicator light (green) turns
on.
1. Indicator light
2. Push button start
NOTE
xIf the push button start indicator
light (green) flashes, make sure
that the key is being carried.
xIf the push button start indicator
light (green)
flashes with the key
being carried, touch the key to
the push button start and start
the engine.
Refer to Engine Start Function
When Key Battery is Dead on
page 4-8.
CAUTION
If the KEY warning indication (red)
is displayed, or the push button
start indicator light (amber)
flashes,
this could indicate a problem with
the engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC
or ON.
Refer to KEY Warning Indication/
Warning Light (Red) on page
7-56.
Have your vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible.
NOTE
xUnder the following conditions,
the KEY warning indication (red)
is displayed after the push button
start is pressed. This informs the
driver that the push button start
will not switch to ACC, even if it
is pressed from off (page 7-56).
xThe key battery is dead.xThe key is out of operational
range.
xThe key is placed in areas where
it is difficult for the system to
detect the signal (page 3-7).
When Driving
Start/Stop Engine
4-6

xA key from another
manufacturer similar to the key
is in the operational range.
x(Forced engine starting method)
If the KEY warning indication
(red) is displayed, or the push
button start indicator light
(amber) flashes, this could
indicate that the engine may not
start using the usual starting
method (page 7-56). Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible. If this occurs,
the engine can be force-started.
Press and hold the push button
start until the engine starts. Other
procedures necessary for starting
the engine, such as having the key
in the cabin, and depressing the
clutch pedal (manual
transmission) or the brake pedal
(automatic transmission) are
required.
xWhen the engine is force-started,
the KEY warning indication (red)
remains displayed and the push
button start indicator light
(amber) remains flashing.
x(Automatic transmission)
When the selector lever is in the
neutral (N) position, the push
button start indicator light (green)
does not turn on.
7. Press the push button start after the
push button start indicator light
(green) turns on.
NOTE
xAfter starting the engine, the push
button start indicator light
(amber) turns off and the ignition
switches to the ON position.
x(SKYACTIV-G 2.0, SKYACTIV-G
2.5, SKYACTIV-X 2.0)
After pressing the push button
start and before the engine starts,
the operation sound of the fuel
pump motor from near the fuel
tank can be heard, however, this
does not indicate a malfunction.
x(SKYACTIV-D 1.8)
xThe starter does not rotate until
the glow indicator light turns
off.
xIf the ignition is left switched
ON for a long period of time
without the engine running
after the glow plugs are
warmed up, the glow plugs may
warm up again which will
illuminate the glow indicator
light.
xWhen starting the engine, do
not release the clutch pedal
(manual transmission) or the
brake pedal (automatic
transmission) until the glow
indicator light in the instrument
cluster turns off and the engine
starts, after pressing the push
button start.
xIf the clutch pedal (manual
transmission) or the brake
pedal (automatic transmission)
is released before the engine
starts, depress the clutch pedal
(manual transmission) or the
brake pedal (automatic
transmission) again and press
the push button start to start
the engine.
8. After starting the engine, let it idle
for about 10 seconds (Prohibited in
Germany).
When Driving
Start/Stop Engine
4-7

NOTE
x(Germany)
Drive immediately after starting
the engine. However do not use
high engine speeds until reaching
the operating temperature.
x(SKYACTIV-G 2.0, SKYACTIV-G
2.5,
SKYACTIV-X 2.0)
xWhether the engine is cold or
warm, it should be started
without the use of the
accelerator.
xIf the engine does not start the
first time, refer to Starting a
Flooded Engine under
Emergency Starting. If the
engine still does not start, have
your vehicle inspected by an
expert repairer (we recommend
an Authorised Mazda Repairer)
(page 7-42).
x(SKYACTIV-D 1.8)
If the ambient temperature is
lower than about >+ 10 °C (14
°F), the maximum engine speed
may not be attained for about 3
minutes after the engine starts to
protect the engine.
x(Manual transmission vehicle
with i-stop function)
If the engine has stopped due to
stalling , it can be restarted by
depressing the clutch pedal
within 3 seconds of the engine
stopping.
The engine cannot be restarted
even if the clutch pedal is
depressed under the following
conditions:
xThe driver's door is open.xThe driver's seat belt is
unfastened.
xThe clutch pedal is not released
completely after the engine
stalled.
xThe clutch pedal is depressed
with the engine not stopped
completely.
▼Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not to
allow the following , otherwise the
signal from the key will not be received
correctly and the engine may not start.
¾Metal parts of other keys or metal
objects touch the key.
¾Spare keys or keys for other vehicles
equipped with an immobilizer
system touch or come near the key.
¾Devices for electronic purchases, or
security passage touch or come near
the key.
If the engine cannot be started due to
a dead key battery, the engine can be
started using the following procedure:
1. Continue to depress the brake
pedal firmly until the engine has
completely started.
2.(Manual transmission)
Continue to depress the clutch
pedal
firmly until the engine has
completely started.
When Driving
Start/Stop Engine
4-8

(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
3. Make sure that the push button
start indication light (green) flashes.
4. Align the centre area of the emblem
on the transmitter with the centre
area of the push button start while
the push button start indicator light
(green) flashes.

1. Indicator light
2. Push button start
3. Transmitter
4. Emblem

5. Make sure that the push button
start indicator light (green) turns
on.
6. Press the push button start to start
the engine.
NOTE
xThe engine cannot be started
unless the clutch pedal is fully
depressed (manual transmission)
or the brake pedal is fully
depressed (automatic
transmission).
xIf there is a malfunction with the
push button start function, the
push button start indicator light
(amber) flashes. In this case, the
engine may start, however, have
the vehicle checked at an expert
repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible.
xIf the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle
checked at an expert repairer (we
recommend an Authorised
Mazda Repairer).
xTo switch the ignition position
without starting the engine,
perform the following operations
after the push button start
indicator light (green) turns on.
1. Release the clutch pedal
(manual transmission) or
brake pedal (automatic
transmission).
2. Press the push button start to
switch the ignition position.
The ignition switches in the
order of ACC, ON, and off
each time the push button
start is pressed. To switch the
ignition position again,
perform the operation from
the beginning.
▼Emergency Operation for Starting
the Engine
If the KEY warning indication (red) is
displayed, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon as
When Driving
Start/Stop Engine
4-9

possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine
starts. Other procedures necessary for
starting the engine such as having the
key in the cabin, and depressing the
clutch pedal (manual transmission) or
the brake pedal (automatic
transmission) are required.Turning the Engine Off
▼Turning the Engine
Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking ,
which could cause an accident and
serious injury.
1. Stop the vehicle completely.
2.(Manual transmission)
Shift into neutral and set the
parking brake.
(Automatic transmission)
Shift the selector lever to the P
position and set the parking brake.
3. Press the push button start to turn
off the engine. The ignition position
is off.
CAUTION
¾When leaving the vehicle, make sure
the push button start is off.
¾(SKYACTIV-D 1.8)
If the engine is started and stopped
repeatedly before it warms up, the
engine may speed up while the
vehicle is stopped to clean the
engine internally. Do not stop the
engine until the engine returns to
running at its normal speed.
When Driving
Start/Stop Engine
4-10

Manual transmission
Engine idle stopping and restarting
while vehicle is stopped
(AUTOHOLD operation turned off)
1. Stop the vehicle by depressing the
brake pedal and then the clutch
pedal.
2. While depressing the clutch pedal,
shift the shift lever to the neutral
position. Engine idling stops after
the clutch pedal is released.
3.(Without M Hybrid)
The engine restarts automatically
when the clutch pedal is depressed.
(With M Hybrid)
Depress the clutch pedal and shift
the shift lever to a position other
than neutral.
The engine restarts automatically
after releasing the brake pedal or
starting to release the clutch pedal.
(When the vehicle is stopped by the
AUTOHOLD function)
1. Bring the vehicle to a complete stop
by depressing the brake pedal first
and then the clutch pedal.
2. While depressing the clutch pedal,
shift the shift lever to neutral. After
releasing your foot from the clutch
pedal, engine idling stops and
continues to be stopped even if the
brake pedal is released.
3.(Without M Hybrid)
The engine restarts automatically
when the clutch pedal is depressed.
(With M Hybrid)
The engine restarts automatically
when the clutch pedal is depressed
with the shift lever in a position
other than neutral.
Engine idle stopping and restarting
while driving (With M Hybrid)
1. The gear shift indicator (GSI)
displays N when engine idling can
be stopped while the shift lever is in
a position other than neutral.
2. Depress the brake pedal.
3. Shift the shift lever to the neutral
position.
4. Engine idling is stopped after
releasing the clutch pedal.
5. The engine restarts automatically
when the clutch pedal is depressed.
Automatic transmission
Engine idle stopping and restarting
while vehicle is stopped
(AUTOHOLD operation turned off and
When not using Mazda Radar Cruise
Control with Stop & Go function
(MRCC with Stop & Go function)/
Cruising & Traffic Support (CTS))
1. Engine idling stops when the brake
pedal is depressed while the vehicle
is driven (except for driving in the R
or M position second gear
fixed
mode) and the vehicle is stopped.
2. The engine restarts automatically
when the brake pedal is released
with the selector lever in the D or
M position (not in second gear
fixed mode).
3. If the selector lever is in the N or P
position, the engine does not
restart when the brake pedal is
released. The engine restarts when
the brake pedal is depressed again
or the selector lever is shifted to the
D, M (not in second gear fixed
mode) or the R position. (For the
purposes of safety, always keep the
brake pedal depressed when
shifting the selector lever while
engine idling is stopped.)
(When the vehicle is stopped by the
MRCC with Stop & Go function/CTS
stop hold control)
1. When the vehicle is stopped by the
MRCC with Stop & Go function/
CTS, engine idling stops and
continues to be stopped without
depressing the brake pedal.
When Driving
Start/Stop Engine
4-12

xThe i-stop warning light (amber) is
not turned on/flashing.
xThe keyless entry & push button start
system functions are normal.
x(With M Hybrid)
xThe temperature and charge
condition of the M Hybrid battery
is good.
xThe Integrated Starter-Generator
(ISG) is in good condition.
x(Without M Hybrid)
xThe brake vacuum is
sufficiently
high.
xThe battery is in good condition.x(Manual transmission)
While vehicle is stopped
xThe vehicle speed is 3 km/h (1.8
mph) or less.
xThe shift lever is in the neutral
position.
xThe clutch pedal is not depressed.
While driving (With M Hybrid)
xThe vehicle speed is 17 km/h (11
mph) or less.
xThe gear shift indicator (GSI)
displays N.
xThe brake pedal is depressed.xThe shift lever is in the neutral
position.
xThe clutch pedal is not depressed.xThe steering wheel is almost in the
straight-ahead position (idling may
not stop even with the steering
wheel in the straight-ahead
position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is not driven on a
slope.
x(Automatic transmission)
While vehicle is stopped
xThe selector lever is in the D or M
position (not in second gear fixed
mode).
xThe automatic transmission
fluid
has warmed up sufficiently.
xThe automatic transmission
fluid
temperature is not abnormally
high.
xThe steering wheel is almost in the
straight-ahead position (idling may
not stop even with the steering
wheel in the straight-ahead
position if force is applied to the
steering wheel. Release the force
applied to the steering wheel to
stop engine idling).
xThe vehicle is stopped by
depressing the brake pedal.
xThe vehicle is not on a steep slope.xThe vehicle is not stopped
suddenly.
While driving (With M Hybrid)
xThe selector lever is in the D
position (not in second gear fixed
mode).
xThe vehicle is driven at a vehicle
speed of about 20 km/h (12 mph)
or faster after engine idling stops
while the vehicle is stopped.
xThe vehicle is driven at a vehicle
speed of about 30 km/h (19 mph)
or faster after engine idling stops
while driving.
xThe vehicle is not driven in sport
mode.
xThe automatic transmission fluid
has warmed up sufficiently.
xThe automatic transmission fluid
temperature is not abnormally
high.
xThe steering wheel is almost in the
straight-ahead position (idling may
not stop even with the steering
wheel in the straight-ahead
When Driving
Start/Stop Engine
4-14

xThe steering wheel is operated
with the selector lever in the D or
M (not in second gear fixed mode)
position.
xThe selector lever is in the M
position and the second gear fixed
mode is selected.
xThe steering wheel is operated.
Engine idling is stopped while
driving
xThe selector lever is in a position
other than the D position.
xThe accelerator pedal is depressed.xSport mode is selected.xThe steering wheel is operated.x(Manual transmission (With M
Hybrid))
xThe shift lever is shifted to the R
position.
xThe brake pedal is depressed with
the shift lever in the neutral
position.
xThe accelerator pedal is depressed.xThe shift lever is shifted to a
position other than neutral with
the brake pedal released and the
clutch pedal depressed.
xThe driver's seat belt is unfastened.
x(Except European model)
x(Manual transmission)
With the shift lever in the neutral
position, the driver's seat belt is
unfastened, the driver's door is
opened, or the bonnet is opened.
x(Automatic transmission)
With the selector lever in the P or
N position, or the D/M range, the
driver's seat belt is unfastened, the
driver's door is opened, or the
bonnet is opened.
Selector lever is operated while
engine idling is stopped and the
vehicle is stopped (automatic
transmission)
If the selector lever is shifted from D or
M (not in second gear fixed mode)
position to N or P position while
engine idling is stopped, the engine
does not restart even when the brake
pedal is released. The engine will
restart if the brake pedal is depressed
again or the selector lever is shifted to
the D, M (not in second gear fixed
mode), or R position. (For the
purposes of safety, always keep the
brake pedal depressed when shifting
the selector lever.)
If the selector lever is shifted from the
D or M (not in second gear fixed
mode) to the N or P position, and the
driver's seat belt is unfastened or the
driver's door is opened, the engine
restarts.
Battery terminals are disconnected
Engine idling may not stop right after
the battery terminals are disconnected.
In addition, if the battery is replaced,
the i-stop functions must be verified.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
▼i-stop OFF Switch
When pressing the switch, the i-stop
function stops and the i-stop OFF
switch indicator light turns on. If the
switch is pressed again, the i-stop
function becomes operational and the
When Driving
Start/Stop Engine
4-16

automatically to ensure safety. Start
the engine using the normal method.
xThe bonnet is opened.xThe driver's seat belt is unfastened
and the driver's door is opened.
x(Except European model)
x(Manual transmission)
A sound is activated when the
door is opened while the engine
idling is stopped with the shift
lever in a position other than
neutral. In this case, the engine
does not restart automatically to
ensure safety. Shift the shift lever to
neutral and start the engine.
xIf the i-stop warning light (amber)
remains on while the engine is
running, the battery performance
may have decreased. Have your
vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
NOTE
A problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when the
ignition is switched ON.
xThe light continues to remain on
while the engine is running.
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected by an expert repairer
(we recommend an Authorised Mazda
Repairer).
i-stop indicator light (green)
When the light is turned on
xThe light turns on while engine idling
is stopped and turns off when the
engine is restarted.
When the light is flashing
x(Manual transmission)
xThe light flashes when the shift
lever is shifted to a position other
than the neutral while engine
idling is stopped to notify the
driver that engine idling is stopped.
xBy depressing the clutch pedal, the
engine restarts automatically and
the light turns off.
x(European model)
The light flashes when the driver's
door is opened while engine idling is
stopped to notify the driver that
engine idling is stopped. It turns off
when the driver's door is closed.
When Driving
Start/Stop Engine
4-19